/* * This program reads various mode pages and bits of other
* information from a scsi device and interprets the raw data for you
* with a report written to stdout. Usage:
*
* ./sginfo [options] /dev/sg2 [replace parameters]
*
* Options are:
* -6 do 6 byte mode sense + select (default: 10 byte)
* -a display all mode pages reported by the device: equivalent to '-t 63'.
* -A display all mode pages and subpages reported by the device: equivalent
* to '-t 63,255'.
* -c access Cache control page.
* -C access Control Page.
* -d display defect lists (default format: index).
* -D access disconnect-reconnect page.
* -e access Read-Write error recovery page.
* -E access Control Extension page.
* -f access Format Device Page.
* -Farg defect list format (-Flogical, -flba64, -Fphysical, -Findex, -Fhead)
* -g access rigid disk geometry page.
* -G display only "grown" defect list (default format: index)
* -i display information from Inquiry command.
* -I access Informational Exceptions page.
* -l list known scsi devices on the system [deprecated]
* -n access notch parameters page.
* -N Negate (stop) storing to saved page (active with -R)
* -P access Power Condition Page.
* -r list known raw scsi devices on the system
* -s display serial number (from INQUIRY VPD page)
* -t <n[,spn]> access page number <n> [and subpage <spn>], try to decode
* -u <n[,spn]> access page number <n> [and subpage <spn>], output in hex
* -v show this program's version number
* -V access Verify Error Recovery Page.
* -T trace commands (for debugging, double for more debug)
* -z do a single fetch for mode pages (rather than double fetch)
*
* Only one of the following three options can be specified.
* None of these three implies the current values are returned.
* -m Display modifiable fields instead of current values
* -M Display manufacturer defaults instead of current values
* -S Display saved defaults instead of current values
*
* -X Display output values in a list.
* -R Replace parameters - best used with -X
*
* Eric Youngdale - 11/1/93. Version 1.0.
*
* Version 1.1: Ability to change parameters on cache page, support for
* X front end.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2, or (at your option)
* any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*
* Michael Weller (eowmob at exp-math dot uni-essen dot de)
* 11/23/94 massive extensions from 1.4a
* 08/23/97 fix problems with defect lists
*
* Douglas Gilbert (dgilbert at interlog dot com)
* 990628 port to sg .... (version 1.81)
* up 4KB limit on defect list to 32KB
* 'sginfo -l' also shows sg devices and mapping to other
* scsi devices
* 'sginfo' commands can take either an sd, sr (scd), st
* or an sg device (all non-sg devices converted to a
* sg device)
*
* 001208 Add Kurt Garloff's "-uno" flag for displaying info
* from a page number. <garloff at suse dot de> [version 1.90]
*
* Kurt Garloff <garloff at suse dot de>
* 20000715 allow displaying and modification of vendor specific pages
* (unformatted - @ hexdatafield)
* accept vendor lengths for those pages
* enabled page saving
* cleaned parameter parsing a bit (it's still a terrible mess!)
* Use sr (instead of scd) and sg%d (instead of sga,b,...) in -l
* and support much more devs in -l (incl. nosst)
* Fix segfault in defect list (len=0xffff) and adapt formatting
* to large disks. Support up to 256kB defect lists with
* 0xB7 (12byte) command if necessary and fallback to 0x37
* (10byte) in case of failure. Report truncation.
* sizeof(buffer) (which is sizeof(char*) == 4 or 32 bit archs)
* was used incorrectly all over the place. Fixed.
* [version 1.95]
* Douglas Gilbert (dgilbert at interlog dot com)
* 20020113 snprintf() type cleanup [version 1.96]
* 20021211 correct sginfo MODE_SELECT, protect against block devices
* that answer sg's ioctls. [version 1.97]
* 20021228 scan for some "scd<n>" as well as "sr<n>" device names [1.98]
* 20021020 Update control page [1.99]
*
* Thomas Steudten (thomas at steudten dot com)
* 20040521 add -Fhead feature [version 2.04]
*
* Tim Hunt (tim at timhunt dot net)
* 20050427 increase number of mapped SCSI disks devices
*
* Dave Johnson (djj at ccv dot brown dot edu)
* 20051218 improve disk defect list handling
*/
/*
* N.B. This utility is in maintenance mode only. This means that serious
* bugs will be fixed but no new features or mode page changes will be
* added. Please use the sdparm utility. D. Gilbert 20090316
*/
#define _XOPEN_SOURCE 500
#ifndef _GNU_SOURCE
#define _GNU_SOURCE 1
#endif
static const char * version_str = "2.42 [20180811]";
#include <stdio.h>
#include <string.h>
#include <getopt.h>
#include <unistd.h>
#include <stdlib.h>
#include <fcntl.h>
#include <errno.h>
#include <stdlib.h>
#include <ctype.h>
#define __STDC_FORMAT_MACROS 1
#include <inttypes.h>
#include <sys/ioctl.h>
#include <sys/types.h>
#include <sys/stat.h>
#include <dirent.h>
#ifdef HAVE_CONFIG_H
#include "config.h"
#endif
#include "sg_io_linux.h"
static int glob_fd;
static char *device_name;
#define MAX_SG_DEVS 8192
#define MAX_RESP6_SIZE 252
#define MAX_RESP10_SIZE (4*1024)
#define MAX_BUFFER_SIZE MAX_RESP10_SIZE
#define INQUIRY_RESP_INITIAL_LEN 36
#define MAX_INQFIELD_LEN 17
#define MAX_HEADS 127
#define HEAD_SORT_TOKEN 0x55
#define SIZEOF_BUFFER (16*1024)
#define SIZEOF_BUFFER1 (16*1024)
static uint8_t cbuffer[SIZEOF_BUFFER];
static uint8_t cbuffer1[SIZEOF_BUFFER1];
static uint8_t cbuffer2[SIZEOF_BUFFER1];
static char defect = 0;
static char defectformat = 0x4;
static char grown_defect = 0;
static char negate_sp_bit = 0;
static char replace = 0;
static char serial_number = 0;
static char x_interface = 0;
static char single_fetch = 0;
static char mode6byte = 0; /* defaults to 10 byte mode sense + select */
static char trace_cmd = 0;
struct mpage_info {
int page;
int subpage;
int page_control;
int peri_type;
int inq_byte6; /* EncServ and MChngr bits of interest */
int resp_len;
};
/* declarations of functions decoding known mode pages */
static int common_disconnect_reconnect(struct mpage_info * mpi,
const char * prefix);
static int common_control(struct mpage_info * mpi, const char * prefix);
static int common_control_extension(struct mpage_info * mpi,
const char * prefix);
static int common_proto_spec_lu(struct mpage_info * mpi, const char * prefix);
static int common_proto_spec_port(struct mpage_info * mpi,
const char * prefix);
static int common_proto_spec_port_sp1(struct mpage_info * mpi,
const char * prefix);
static int common_proto_spec_port_sp2(struct mpage_info * mpi,
const char * prefix);
static int common_power_condition(struct mpage_info * mpi,
const char * prefix);
static int common_informational(struct mpage_info * mpi, const char * prefix);
static int disk_error_recovery(struct mpage_info * mpi, const char * prefix);
static int disk_format(struct mpage_info * mpi, const char * prefix);
static int disk_verify_error_recovery(struct mpage_info * mpi,
const char * prefix);
static int disk_geometry(struct mpage_info * mpi, const char * prefix);
static int disk_notch_parameters(struct mpage_info * mpi, const char * prefix);
static int disk_cache(struct mpage_info * mpi, const char * prefix);
static int disk_xor_control(struct mpage_info * mpi, const char * prefix);
static int disk_background(struct mpage_info * mpi, const char * prefix);
static int optical_memory(struct mpage_info * mpi, const char * prefix);
static int cdvd_error_recovery(struct mpage_info * mpi, const char * prefix);
static int cdvd_mrw(struct mpage_info * mpi, const char * prefix);
static int cdvd_write_param(struct mpage_info * mpi, const char * prefix);
static int cdvd_audio_control(struct mpage_info * mpi, const char * prefix);
static int cdvd_timeout(struct mpage_info * mpi, const char * prefix);
static int cdvd_device_param(struct mpage_info * mpi, const char * prefix);
static int cdvd_cache(struct mpage_info * mpi, const char * prefix);
static int cdvd_mm_capab(struct mpage_info * mpi, const char * prefix);
static int cdvd_feature(struct mpage_info * mpi, const char * prefix);
static int tape_data_compression(struct mpage_info * mpi, const char * prefix);
static int tape_dev_config(struct mpage_info * mpi, const char * prefix);
static int tape_medium_part1(struct mpage_info * mpi, const char * prefix);
static int tape_medium_part2_4(struct mpage_info * mpi, const char * prefix);
static int ses_services_manag(struct mpage_info * mpi, const char * prefix);
static int spi4_training_config(struct mpage_info * mpi, const char * prefix);
static int spi4_negotiated(struct mpage_info * mpi, const char * prefix);
static int spi4_report_xfer(struct mpage_info * mpi, const char * prefix);
enum page_class {PC_COMMON, PC_DISK, PC_TAPE, PC_CDVD, PC_SES, PC_SMC};
struct mpage_name_func {
int page;
int subpage;
enum page_class pg_class;
const char * name;
int (*func)(struct mpage_info *, const char *);
};
#define MP_LIST_PAGES 0x3f
#define MP_LIST_SUBPAGES 0xff
static struct mpage_name_func mpage_common[] =
{
{ 0, 0, PC_COMMON, "Vendor (non-page format)", NULL},
{ 2, 0, PC_COMMON, "Disconnect-Reconnect", common_disconnect_reconnect},
{ 9, 0, PC_COMMON, "Peripheral device (obsolete)", NULL},
{ 0xa, 0, PC_COMMON, "Control", common_control},
{ 0xa, 1, PC_COMMON, "Control Extension", common_control_extension},
{ 0x15, 0, PC_COMMON, "Extended", NULL},
{ 0x16, 0, PC_COMMON, "Extended, device-type specific", NULL},
{ 0x18, 0, PC_COMMON, "Protocol specific lu", common_proto_spec_lu},
{ 0x19, 0, PC_COMMON, "Protocol specific port", common_proto_spec_port},
{ 0x19, 1, PC_COMMON, "Protocol specific port, subpage 1 overload",
common_proto_spec_port_sp1},
{ 0x19, 2, PC_COMMON, "Protocol specific port, subpage 2 overload",
common_proto_spec_port_sp2},
/* { 0x19, 2, PC_COMMON, "SPI-4 Saved Training configuration",
spi4_training_config}, */
{ 0x19, 3, PC_COMMON, "SPI-4 Negotiated Settings", spi4_negotiated},
{ 0x19, 4, PC_COMMON, "SPI-4 Report transfer capabilities",
spi4_report_xfer},
{ 0x1a, 0, PC_COMMON, "Power Condition", common_power_condition},
{ 0x1c, 0, PC_COMMON, "Informational Exceptions", common_informational},
{ MP_LIST_PAGES, 0, PC_COMMON, "Return all pages", NULL},
};
static const int mpage_common_len = sizeof(mpage_common) /
sizeof(mpage_common[0]);
static struct mpage_name_func mpage_disk[] =
{
{ 1, 0, PC_DISK, "Read-Write Error Recovery", disk_error_recovery},
{ 3, 0, PC_DISK, "Format Device", disk_format},
{ 4, 0, PC_DISK, "Rigid Disk Geometry", disk_geometry},
{ 5, 0, PC_DISK, "Flexible Disk", NULL},
{ 6, 0, PC_DISK, "Optical memory", optical_memory},
{ 7, 0, PC_DISK, "Verify Error Recovery", disk_verify_error_recovery},
{ 8, 0, PC_DISK, "Caching", disk_cache},
{ 0xa, 0xf1, PC_DISK, "Parallel ATA control (SAT)", NULL},
{ 0xb, 0, PC_DISK, "Medium Types Supported", NULL},
{ 0xc, 0, PC_DISK, "Notch and Partition", disk_notch_parameters},
{ 0x10, 0, PC_DISK, "XOR control", disk_xor_control},
{ 0x1c, 1, PC_DISK, "Background control", disk_background},
};
static const int mpage_disk_len = sizeof(mpage_disk) / sizeof(mpage_disk[0]);
static struct mpage_name_func mpage_cdvd[] =
{
{ 1, 0, PC_CDVD, "Read-Write Error Recovery (cdvd)",
cdvd_error_recovery},
{ 3, 0, PC_CDVD, "MRW", cdvd_mrw},
{ 5, 0, PC_CDVD, "Write parameters", cdvd_write_param},
{ 8, 0, PC_CDVD, "Caching", cdvd_cache},
{ 0xd, 0, PC_CDVD, "CD device parameters", cdvd_device_param},
{ 0xe, 0, PC_CDVD, "CD audio control", cdvd_audio_control},
{ 0x18, 0, PC_CDVD, "Feature set support & version", cdvd_feature},
{ 0x1a, 0, PC_CDVD, "Power Condition", common_power_condition},
{ 0x1c, 0, PC_CDVD, "Fault/failure reporting control",
common_informational},
{ 0x1d, 0, PC_CDVD, "Time-out & protect", cdvd_timeout},
{ 0x2a, 0, PC_CDVD, "MM capabilities & mechanical status", cdvd_mm_capab},
};
static const int mpage_cdvd_len = sizeof(mpage_cdvd) / sizeof(mpage_cdvd[0]);
static struct mpage_name_func mpage_tape[] =
{
{ 1, 0, PC_TAPE, "Read-Write Error Recovery", disk_error_recovery},
{ 0xf, 0, PC_TAPE, "Data compression", tape_data_compression},
{ 0x10, 0, PC_TAPE, "Device configuration", tape_dev_config},
{ 0x10, 1, PC_TAPE, "Device configuration extension", NULL},
{ 0x11, 0, PC_TAPE, "Medium partition(1)", tape_medium_part1},
{ 0x12, 0, PC_TAPE, "Medium partition(2)", tape_medium_part2_4},
{ 0x13, 0, PC_TAPE, "Medium partition(3)", tape_medium_part2_4},
{ 0x14, 0, PC_TAPE, "Medium partition(4)", tape_medium_part2_4},
{ 0x1c, 0, PC_TAPE, "Informational Exceptions", common_informational},
{ 0x1d, 0, PC_TAPE, "Medium configuration", NULL},
};
static const int mpage_tape_len = sizeof(mpage_tape) / sizeof(mpage_tape[0]);
static struct mpage_name_func mpage_ses[] =
{
{ 0x14, 0, PC_SES, "Enclosure services management", ses_services_manag},
};
static const int mpage_ses_len = sizeof(mpage_ses) / sizeof(mpage_ses[0]);
static struct mpage_name_func mpage_smc[] =
{
{ 0x1d, 0, PC_SMC, "Element address assignment", NULL},
{ 0x1e, 0, PC_SMC, "Transport geometry parameters", NULL},
{ 0x1f, 0, PC_SMC, "Device capabilities", NULL},
{ 0x1f, 1, PC_SMC, "Extended device capabilities", NULL},
};
static const int mpage_smc_len = sizeof(mpage_smc) / sizeof(mpage_smc[0]);
#define MAXPARM 64
static int next_parameter;
static int n_replacement_values;
static uint64_t replacement_values[MAXPARM];
static char is_hex[MAXPARM];
#define SMODE_SENSE 0x1a
#define SMODE_SENSE_10 0x5a
#define SMODE_SELECT 0x15
#define SMODE_SELECT_10 0x55
#define MPHEADER6_LEN 4
#define MPHEADER10_LEN 8
/* forward declarations */
static void usage(const char *);
static void dump(void *buffer, unsigned int length);
#define DXFER_NONE 0
#define DXFER_FROM_DEVICE 1
#define DXFER_TO_DEVICE 2
struct scsi_cmnd_io
{
uint8_t * cmnd; /* ptr to SCSI command block (cdb) */
size_t cmnd_len; /* number of bytes in SCSI command */
int dxfer_dir; /* DXFER_NONE, DXFER_FROM_DEVICE, or
DXFER_TO_DEVICE */
uint8_t * dxferp; /* ptr to outgoing/incoming data */
size_t dxfer_len; /* bytes to be transferred to/from dxferp */
};
#define SENSE_BUFF_LEN 64
#define CMD_TIMEOUT 60000 /* 60,000 milliseconds (60 seconds) */
#define EBUFF_SZ 512
#define GENERAL_ERROR 1
#define UNKNOWN_OPCODE 2
#define BAD_CDB_FIELD 3
#define UNSUPPORTED_PARAM 4
#define DEVICE_ATTENTION 5
#define DEVICE_NOT_READY 6
#define DECODE_FAILED_TRY_HEX 9999
/* Returns 0 -> ok, 1 -> general error, 2 -> unknown opcode,
3 -> unsupported field in cdb, 4 -> unsupported param in data-in */
static int
do_scsi_io(struct scsi_cmnd_io * sio)
{
uint8_t sense_b[SENSE_BUFF_LEN];
struct sg_io_hdr io_hdr;
struct sg_scsi_sense_hdr ssh;
int res;
memset(&io_hdr, 0, sizeof(struct sg_io_hdr));
io_hdr.interface_id = 'S';
io_hdr.cmd_len = sio->cmnd_len;
io_hdr.mx_sb_len = sizeof(sense_b);
if (DXFER_NONE == sio->dxfer_dir)
io_hdr.dxfer_direction = SG_DXFER_NONE;
else
io_hdr.dxfer_direction = (DXFER_TO_DEVICE == sio->dxfer_dir) ?
SG_DXFER_TO_DEV : SG_DXFER_FROM_DEV;
io_hdr.dxfer_len = sio->dxfer_len;
io_hdr.dxferp = sio->dxferp;
io_hdr.cmdp = sio->cmnd;
io_hdr.sbp = sense_b;
io_hdr.timeout = CMD_TIMEOUT;
if (trace_cmd) {
printf(" cdb:");
dump(sio->cmnd, sio->cmnd_len);
}
if ((trace_cmd > 1) && (DXFER_TO_DEVICE == sio->dxfer_dir)) {
printf(" additional data:\n");
dump(sio->dxferp, sio->dxfer_len);
}
if (ioctl(glob_fd, SG_IO, &io_hdr) < 0) {
perror("do_scsi_cmd: SG_IO error");
return GENERAL_ERROR;
}
res = sg_err_category3(&io_hdr);
switch (res) {
case SG_LIB_CAT_RECOVERED:
sg_chk_n_print3("do_scsi_cmd, continuing", &io_hdr, true);
#if defined(__GNUC__)
#if (__GNUC__ >= 7)
__attribute__((fallthrough));
/* FALL THROUGH */
#endif
#endif
case SG_LIB_CAT_CLEAN:
return 0;
default:
if (trace_cmd) {
char ebuff[EBUFF_SZ];
snprintf(ebuff, EBUFF_SZ, "do_scsi_io: opcode=0x%x", sio->cmnd[0]);
sg_chk_n_print3(ebuff, &io_hdr, true);
}
if (sg_normalize_sense(&io_hdr, &ssh)) {
if (ILLEGAL_REQUEST == ssh.sense_key) {
if (0x20 == ssh.asc)
return UNKNOWN_OPCODE;
else if (0x24 == ssh.asc)
return BAD_CDB_FIELD;
else if (0x26 == ssh.asc)
return UNSUPPORTED_PARAM;
} else if (UNIT_ATTENTION == ssh.sense_key)
return DEVICE_ATTENTION;
else if (NOT_READY == ssh.sense_key)
return DEVICE_NOT_READY;
}
return GENERAL_ERROR;
}
}
struct mpage_name_func * get_mpage_info(int page_no, int subpage_no,
struct mpage_name_func * mpp, int elems)
{
int k;
for (k = 0; k < elems; ++k, ++mpp) {
if ((mpp->page == page_no) && (mpp->subpage == subpage_no))
return mpp;
if (mpp->page > page_no)
break;
}
return NULL;
}
enum page_class get_page_class(struct mpage_info * mpi)
{
switch (mpi->peri_type)
{
case 0:
case 4:
case 7:
case 0xe: /* should be RBC */
return PC_DISK;
case 1:
case 2:
return PC_TAPE;
case 8:
return PC_SMC;
case 5:
return PC_CDVD;
case 0xd:
return PC_SES;
default:
return PC_COMMON;
}
}
struct mpage_name_func * get_mpage_name_func(struct mpage_info * mpi)
{
struct mpage_name_func * mpf = NULL;
switch (get_page_class(mpi))
{
case PC_DISK:
mpf = get_mpage_info(mpi->page, mpi->subpage, mpage_disk,
mpage_disk_len);
break;
case PC_CDVD:
mpf = get_mpage_info(mpi->page, mpi->subpage, mpage_cdvd,
mpage_cdvd_len);
break;
case PC_TAPE:
mpf = get_mpage_info(mpi->page, mpi->subpage, mpage_tape,
mpage_tape_len);
break;
case PC_SES:
mpf = get_mpage_info(mpi->page, mpi->subpage, mpage_ses,
mpage_ses_len);
break;
case PC_SMC:
mpf = get_mpage_info(mpi->page, mpi->subpage, mpage_smc,
mpage_smc_len);
break;
case PC_COMMON:
/* picked up it catch all next */
break;
}
if (NULL == mpf) {
if ((PC_SES != get_page_class(mpi)) && (mpi->inq_byte6 & 0x40)) {
/* check for attached enclosure services processor */
mpf = get_mpage_info(mpi->page, mpi->subpage, mpage_ses,
mpage_ses_len);
}
if ((PC_SMC != get_page_class(mpi)) && (mpi->inq_byte6 & 0x8)) {
/* check for attached medium changer device */
mpf = get_mpage_info(mpi->page, mpi->subpage, mpage_smc,
mpage_smc_len);
}
}
if (NULL == mpf)
mpf = get_mpage_info(mpi->page, mpi->subpage, mpage_common,
mpage_common_len);
return mpf;
}
static char unkn_page_str[64];
static const char *
get_page_name(struct mpage_info * mpi)
{
struct mpage_name_func * mpf;
if (MP_LIST_PAGES == mpi->page) {
if (MP_LIST_SUBPAGES == mpi->subpage)
return "List supported pages and subpages";
else
return "List supported pages";
}
mpf = get_mpage_name_func(mpi);
if ((NULL == mpf) || (NULL == mpf->name)) {
if (mpi->subpage)
snprintf(unkn_page_str, sizeof(unkn_page_str),
"page number=0x%x, subpage number=0x%x",
mpi->page, mpi->subpage);
else
snprintf(unkn_page_str, sizeof(unkn_page_str),
"page number=0x%x", mpi->page);
return unkn_page_str;
}
return mpf->name;
}
static void
dump(void *buffer, unsigned int length)
{
unsigned int i;
printf(" ");
for (i = 0; i < length; i++) {
#if 0
if (((uint8_t *) buffer)[i] > 0x20)
printf(" %c ", (unsigned int) ((uint8_t *) buffer)[i]);
else
#endif
printf("%02x ", (unsigned int) ((uint8_t *) buffer)[i]);
if ((i % 16 == 15) && (i < (length - 1))) {
printf("\n ");
}
}
printf("\n");
}
static int
getnbyte(const uint8_t *pnt, int nbyte)
{
unsigned int result;
int i;
if (nbyte > 4)
fprintf(stderr, "getnbyte() limited to 32 bits, nbyte=%d\n", nbyte);
result = 0;
for (i = 0; i < nbyte; i++)
result = (result << 8) | (pnt[i] & 0xff);
return result;
}
static int64_t
getnbyte_ll(const uint8_t *pnt, int nbyte)
{
int64_t result;
int i;
if (nbyte > 8)
fprintf(stderr, "getnbyte_ll() limited to 64 bits, nbyte=%d\n",
nbyte);
result = 0;
for (i = 0; i < nbyte; i++)
result = (result << 8) + (pnt[i] & 0xff);
return result;
}
static int
putnbyte(uint8_t *pnt, unsigned int value,
unsigned int nbyte)
{
int i;
for (i = nbyte - 1; i >= 0; i--) {
pnt[i] = value & 0xff;
value = value >> 8;
}
return 0;
}
#define REASON_SZ 128
static void
check_parm_type(int i)
{
char reason[REASON_SZ];
if (i == 1 && is_hex[next_parameter] != 1) {
snprintf(reason, REASON_SZ,
"simple number (pos %i) instead of @ hexdatafield: %"
PRIu64 , next_parameter, replacement_values[next_parameter]);
usage(reason);
}
if (i != 1 && is_hex[next_parameter]) {
snprintf(reason, REASON_SZ,
"@ hexdatafield (pos %i) instead of a simple number: %"
PRIu64 , next_parameter, replacement_values[next_parameter]);
usage(reason);
}
}
static void
bitfield(uint8_t *pageaddr, const char * text, int mask, int shift)
{
if (x_interface && replace) {
check_parm_type(0);
*pageaddr = (*pageaddr & ~(mask << shift)) |
((replacement_values[next_parameter++] & mask) << shift);
} else if (x_interface)
printf("%d ", (*pageaddr >> shift) & mask);
else
printf("%-35s%d\n", text, (*pageaddr >> shift) & mask);
}
#if 0
static void
notbitfield(uint8_t *pageaddr, char * text, int mask,
int shift)
{
if (modifiable) {
bitfield(pageaddr, text, mask, shift);
return;
}
if (x_interface && replace) {
check_parm_type(0);
*pageaddr = (*pageaddr & ~(mask << shift)) |
(((!replacement_values[next_parameter++]) & mask) << shift);
} else if (x_interface)
printf("%d ", !((*pageaddr >> shift) & mask));
else
printf("%-35s%d\n", text, !((*pageaddr >> shift) & mask));
}
#endif
static void
intfield(uint8_t * pageaddr, int nbytes, const char * text)
{
if (x_interface && replace) {
check_parm_type(0);
putnbyte(pageaddr, replacement_values[next_parameter++], nbytes);
} else if (x_interface)
printf("%d ", getnbyte(pageaddr, nbytes));
else
printf("%-35s%d\n", text, getnbyte(pageaddr, nbytes));
}
static void
hexfield(uint8_t * pageaddr, int nbytes, const char * text)
{
if (x_interface && replace) {
check_parm_type(0);
putnbyte(pageaddr, replacement_values[next_parameter++], nbytes);
} else if (x_interface)
printf("%d ", getnbyte(pageaddr, nbytes));
else
printf("%-35s0x%x\n", text, getnbyte(pageaddr, nbytes));
}
static void
hexdatafield(uint8_t * pageaddr, int nbytes, const char * text)
{
if (x_interface && replace) {
uint8_t *ptr;
unsigned tmp;
/* Though in main we ensured that a @string has the right format,
we have to check that we are working on a @ hexdata field */
check_parm_type(1);
ptr = (uint8_t *) (unsigned long)
(replacement_values[next_parameter++]);
ptr++; /* Skip @ */
while (*ptr) {
if (!nbytes)
goto illegal;
tmp = (*ptr >= 'a') ? (*ptr - 'a' + 'A') : *ptr;
tmp -= (tmp >= 'A') ? 'A' - 10 : '0';
*pageaddr = tmp << 4;
ptr++;
tmp = (*ptr >= 'a') ? (*ptr - 'a' + 'A') : *ptr;
tmp -= (tmp >= 'A') ? 'A' - 10 : '0';
*pageaddr++ += tmp;
ptr++;
nbytes--;
}
if (nbytes) {
illegal:
fputs("sginfo: incorrect number of bytes in @hexdatafield.\n",
stdout);
exit(2);
}
} else if (x_interface) {
putchar('@');
while (nbytes-- > 0)
printf("%02x", *pageaddr++);
putchar(' ');
} else {
printf("%-35s0x", text);
while (nbytes-- > 0)
printf("%02x", *pageaddr++);
putchar('\n');
}
}
/* Offset into mode sense (6 or 10 byte) response that actual mode page
* starts at (relative to resp[0]). Returns -1 if problem */
static int
modePageOffset(const uint8_t * resp, int len, int modese_6)
{
int bd_len;
int resp_len = 0;
int offset = -1;
if (resp) {
if (modese_6) {
resp_len = resp[0] + 1;
bd_len = resp[3];
offset = bd_len + MPHEADER6_LEN;
} else {
resp_len = (resp[0] << 8) + resp[1] + 2;
bd_len = (resp[6] << 8) + resp[7];
/* LongLBA doesn't change this calculation */
offset = bd_len + MPHEADER10_LEN;
}
if ((offset + 2) > len) {
printf("modePageOffset: raw_curr too small, offset=%d "
"resp_len=%d bd_len=%d\n", offset, resp_len, bd_len);
offset = -1;
} else if ((offset + 2) > resp_len) {
printf("modePageOffset: response length too short, resp_len=%d"
" offset=%d bd_len=%d\n", resp_len, offset, bd_len);
offset = -1;
}
}
return offset;
}
/* Reads mode (sub-)page via 6 byte MODE SENSE, returns 0 if ok */
static int
get_mode_page6(struct mpage_info * mpi, int dbd, uint8_t * resp,
int sngl_fetch)
{
int status, off;
uint8_t cmd[6];
struct scsi_cmnd_io sci;
int initial_len = (sngl_fetch ? MAX_RESP6_SIZE : 4);
memset(resp, 0, 4);
cmd[0] = SMODE_SENSE; /* MODE SENSE (6) */
cmd[1] = 0x00 | (dbd ? 0x8 : 0); /* disable block descriptors bit */
cmd[2] = (mpi->page_control << 6) | mpi->page;
cmd[3] = mpi->subpage; /* subpage code */
cmd[4] = initial_len;
cmd[5] = 0x00; /* control */
sci.cmnd = cmd;
sci.cmnd_len = sizeof(cmd);
sci.dxfer_dir = DXFER_FROM_DEVICE;
sci.dxfer_len = initial_len;
sci.dxferp = resp;
status = do_scsi_io(&sci);
if (status) {
if (mpi->subpage)
fprintf(stdout, ">>> Unable to read %s mode page 0x%x, subpage "
"0x%x [mode_sense_6]\n", get_page_name(mpi), mpi->page,
mpi->subpage);
else
fprintf(stdout, ">>> Unable to read %s mode page (0x%x) "
"[mode_sense_6]\n", get_page_name(mpi), mpi->page);
return status;
}
mpi->resp_len = resp[0] + 1;
if (sngl_fetch) {
if (trace_cmd > 1) {
off = modePageOffset(resp, mpi->resp_len, 1);
if (off >= 0) {
printf(" cdb response:\n");
dump(resp, mpi->resp_len);
}
}
return status;
}
cmd[4] = mpi->resp_len;
sci.cmnd = cmd;
sci.cmnd_len = sizeof(cmd);
sci.dxfer_dir = DXFER_FROM_DEVICE;
sci.dxfer_len = mpi->resp_len;
sci.dxferp = resp;
status = do_scsi_io(&sci);
if (status) {
if (mpi->subpage)
fprintf(stdout, ">>> Unable to read %s mode page 0x%x, subpage "
"0x%x [mode_sense_6]\n", get_page_name(mpi), mpi->page,
mpi->subpage);
else
fprintf(stdout, ">>> Unable to read %s mode page (0x%x) "
"[mode_sense_6]\n", get_page_name(mpi), mpi->page);
} else if (trace_cmd > 1) {
off = modePageOffset(resp, mpi->resp_len, 1);
if (off >= 0) {
printf(" cdb response:\n");
dump(resp, mpi->resp_len);
}
}
return status;
}
/* Reads mode (sub-)page via 10 byte MODE SENSE, returns 0 if ok */
static int
get_mode_page10(struct mpage_info * mpi, int llbaa, int dbd,
uint8_t * resp, int sngl_fetch)
{
int status, off;
uint8_t cmd[10];
struct scsi_cmnd_io sci;
int initial_len = (sngl_fetch ? MAX_RESP10_SIZE : 4);
memset(resp, 0, 4);
cmd[0] = SMODE_SENSE_10; /* MODE SENSE (10) */
cmd[1] = 0x00 | (llbaa ? 0x10 : 0) | (dbd ? 0x8 : 0);
cmd[2] = (mpi->page_control << 6) | mpi->page;
cmd[3] = mpi->subpage;
cmd[4] = 0x00; /* (reserved) */
cmd[5] = 0x00; /* (reserved) */
cmd[6] = 0x00; /* (reserved) */
cmd[7] = (initial_len >> 8) & 0xff;
cmd[8] = initial_len & 0xff;
cmd[9] = 0x00; /* control */
sci.cmnd = cmd;
sci.cmnd_len = sizeof(cmd);
sci.dxfer_dir = DXFER_FROM_DEVICE;
sci.dxfer_len = initial_len;
sci.dxferp = resp;
status = do_scsi_io(&sci);
if (status) {
if (mpi->subpage)
fprintf(stdout, ">>> Unable to read %s mode page 0x%x, subpage "
"0x%x [mode_sense_10]\n", get_page_name(mpi), mpi->page,
mpi->subpage);
else {
fprintf(stdout, ">>> Unable to read %s mode page (0x%x) "
"[mode_sense_10]\n", get_page_name(mpi), mpi->page);
return status;
}
}
mpi->resp_len = (resp[0] << 8) + resp[1] + 2;
if (sngl_fetch) {
if (trace_cmd > 1) {
off = modePageOffset(resp, mpi->resp_len, 0);
if (off >= 0) {
printf(" cdb response:\n");
dump(resp, mpi->resp_len);
}
}
return status;
}
cmd[7] = (mpi->resp_len >> 8) & 0xff;
cmd[8] = (mpi->resp_len & 0xff);
sci.cmnd = cmd;
sci.cmnd_len = sizeof(cmd);
sci.dxfer_dir = DXFER_FROM_DEVICE;
sci.dxfer_len = mpi->resp_len;
sci.dxferp = resp;
status = do_scsi_io(&sci);
if (status) {
if (mpi->subpage)
fprintf(stdout, ">>> Unable to read %s mode page 0x%x, subpage "
"0x%x [mode_sense_10]\n", get_page_name(mpi), mpi->page,
mpi->subpage);
else
fprintf(stdout, ">>> Unable to read %s mode page (0x%x) "
"[mode_sense_10]\n", get_page_name(mpi), mpi->page);
} else if (trace_cmd > 1) {
off = modePageOffset(resp, mpi->resp_len, 0);
if (off >= 0) {
printf(" cdb response:\n");
dump(resp, mpi->resp_len);
}
}
return status;
}
static int
get_mode_page(struct mpage_info * mpi, int dbd, uint8_t * resp)
{
int res;
if (mode6byte)
res = get_mode_page6(mpi, dbd, resp, single_fetch);
else
res = get_mode_page10(mpi, 0, dbd, resp, single_fetch);
if (UNKNOWN_OPCODE == res)
fprintf(stdout, ">>>>> Try command again with%s '-6' "
"argument\n", (mode6byte ? "out the" : " a"));
else if (mpi->subpage && (BAD_CDB_FIELD == res))
fprintf(stdout, ">>>>> device doesn't seem to support "
"subpages\n");
else if (DEVICE_ATTENTION == res)
fprintf(stdout, ">>>>> device reports UNIT ATTENTION, check it or"
" just try again\n");
else if (DEVICE_NOT_READY == res)
fprintf(stdout, ">>>>> device NOT READY, does it need media?\n");
return res;
}
/* Contents should point to the mode parameter header that we obtained
in a prior read operation. This way we do not have to work out the
format of the beast. Assume 0 or 1 block descriptors. */
static int
put_mode_page6(struct mpage_info * mpi, const uint8_t * msense6_resp,
int sp_bit)
{
int status;
int bdlen, resplen;
uint8_t cmd[6];
struct scsi_cmnd_io sci;
bdlen = msense6_resp[3];
resplen = msense6_resp[0] + 1;
cmd[0] = SMODE_SELECT;
cmd[1] = 0x10 | (sp_bit ? 1 : 0); /* always set PF bit */
cmd[2] = 0x00;
cmd[3] = 0x00; /* (reserved) */
cmd[4] = resplen; /* parameter list length */
cmd[5] = 0x00; /* (reserved) */
memcpy(cbuffer1, msense6_resp, resplen);
cbuffer1[0] = 0; /* Mask off the mode data length
- reserved field */
cbuffer1[2] = 0; /* device-specific parameter is not defined
and/or reserved for mode select */
#if 0 /* leave block descriptor alone */
if (bdlen > 0) {
memset(cbuffer1 + MPHEADER6_LEN, 0, 4); /* clear 'number of blocks'
for DAD device */
cbuffer1[MPHEADER6_LEN + 4] = 0; /* clear DAD density code. Why? */
/* leave DAD block length */
}
#endif
cbuffer1[MPHEADER6_LEN + bdlen] &= 0x7f; /* Mask PS bit */
sci.cmnd = cmd;
sci.cmnd_len = sizeof(cmd);
sci.dxfer_dir = DXFER_TO_DEVICE;
sci.dxfer_len = resplen;
sci.dxferp = cbuffer1;
status = do_scsi_io(&sci);
if (status) {
if (mpi->subpage)
fprintf(stdout, ">>> Unable to store %s mode page 0x%x,"
" subpage 0x%x [msel_6]\n", get_page_name(mpi),
mpi->page, mpi->subpage);
else
fprintf(stdout, ">>> Unable to store %s mode page 0x%x [msel_6]\n",
get_page_name(mpi), mpi->page);
}
return status;
}
/* Contents should point to the mode parameter header that we obtained
in a prior read operation. This way we do not have to work out the
format of the beast. Assume 0 or 1 block descriptors. */
static int
put_mode_page10(struct mpage_info * mpi, const uint8_t * msense10_resp,
int sp_bit)
{
int status;
int bdlen, resplen;
uint8_t cmd[10];
struct scsi_cmnd_io sci;
bdlen = (msense10_resp[6] << 8) + msense10_resp[7];
resplen = (msense10_resp[0] << 8) + msense10_resp[1] + 2;
cmd[0] = SMODE_SELECT_10;
cmd[1] = 0x10 | (sp_bit ? 1 : 0); /* always set PF bit */
cmd[2] = 0x00; /* (reserved) */
cmd[3] = 0x00; /* (reserved) */
cmd[4] = 0x00; /* (reserved) */
cmd[5] = 0x00; /* (reserved) */
cmd[6] = 0x00; /* (reserved) */
cmd[7] = (resplen >> 8) & 0xff;
cmd[8] = resplen & 0xff;
cmd[9] = 0x00; /* (reserved) */
memcpy(cbuffer1, msense10_resp, resplen);
cbuffer1[0] = 0; /* Mask off the mode data length */
cbuffer1[1] = 0; /* Mask off the mode data length */
cbuffer1[3] = 0; /* device-specific parameter is not defined
and/or reserved for mode select */
#if 0 /* leave block descriptor alone */
if (bdlen > 0) {
memset(cbuffer1 + MPHEADER10_LEN, 0, 4); /* clear 'number of blocks'
for DAD device */
cbuffer1[MPHEADER10_LEN + 4] = 0; /* clear DAD density code. Why? */
/* leave DAD block length */
}
#endif
cbuffer1[MPHEADER10_LEN + bdlen] &= 0x7f; /* Mask PS bit */
sci.cmnd = cmd;
sci.cmnd_len = sizeof(cmd);
sci.dxfer_dir = DXFER_TO_DEVICE;
sci.dxfer_len = resplen;
sci.dxferp = cbuffer1;
status = do_scsi_io(&sci);
if (status) {
if (mpi->subpage)
fprintf(stdout, ">>> Unable to store %s mode page 0x%x,"
" subpage 0x%x [msel_10]\n", get_page_name(mpi),
mpi->page, mpi->subpage);
else
fprintf(stdout, ">>> Unable to store %s mode page 0x%x "
"[msel_10]\n", get_page_name(mpi), mpi->page);
}
return status;
}
static int
put_mode_page(struct mpage_info * mpi, const uint8_t * msense_resp)
{
if (mode6byte)
return put_mode_page6(mpi, msense_resp, ! negate_sp_bit);
else
return put_mode_page10(mpi, msense_resp, ! negate_sp_bit);
}
static int
setup_mode_page(struct mpage_info * mpi, int nparam, uint8_t * buff,
uint8_t ** o_pagestart)
{
int status, offset, rem_pglen;
uint8_t * pgp;
status = get_mode_page(mpi, 0, buff);
if (status) {
printf("\n");
return status;
}
offset = modePageOffset(buff, mpi->resp_len, mode6byte);
if (offset < 0) {
fprintf(stdout, "mode page=0x%x has bad page format\n", mpi->page);
fprintf(stdout, " perhaps '-z' switch may help\n");
return -1;
}
pgp = buff + offset;
*o_pagestart = pgp;
rem_pglen = (0x40 & pgp[0]) ? ((pgp[2] << 8) + pgp[3]) : pgp[1];
if (x_interface && replace) {
if ((nparam && (n_replacement_values != nparam)) ||
((! nparam) && (n_replacement_values != rem_pglen))) {
fprintf(stdout, "Wrong number of replacement values (%i instead "
"of %i)\n", n_replacement_values,
nparam ? nparam : rem_pglen);
return 1;
}
next_parameter = 1;
}
return 0;
}
static int
get_protocol_id(int port_not_lu, uint8_t * buff, int * proto_idp,
int * offp)
{
int status, off, proto_id, spf;
struct mpage_info mp_i;
char b[64];
memset(&mp_i, 0, sizeof(mp_i));
mp_i.page = (port_not_lu ? 0x19 : 0x18);
/* N.B. getting port or lu specific mode page (not subpage) */
status = get_mode_page(&mp_i, 0, buff);
if (status)
return status;
off = modePageOffset(buff, mp_i.resp_len, mode6byte);
if (off < 0)
return off;
spf = (buff[off] & 0x40) ? 1 : 0; /* subpages won't happen here */
proto_id = buff[off + (spf ? 5 : 2)] & 0xf;
if (trace_cmd > 0)
printf("Protocol specific %s, protocol_id=%s\n",
(port_not_lu ? "port" : "lu"),
sg_get_trans_proto_str(proto_id, sizeof(b), b));
if (proto_idp)
*proto_idp = proto_id;
if (offp)
*offp = off;
return 0;
}
static int
disk_geometry(struct mpage_info * mpi, const char * prefix)
{
int status;
uint8_t *pagestart;
status = setup_mode_page(mpi, 9, cbuffer, &pagestart);
if (status)
return status;
if (prefix[0])
printf("%s", prefix);
if (!x_interface && !replace) {
printf("%s mode page (0x%x)\n", get_page_name(mpi), mpi->page);
printf("-----------------------------------\n");
};
intfield(pagestart + 2, 3, "Number of cylinders");
intfield(pagestart + 5, 1, "Number of heads");
intfield(pagestart + 6, 3, "Starting cyl. write precomp");
intfield(pagestart + 9, 3, "Starting cyl. reduced current");
intfield(pagestart + 12, 2, "Device step rate");
intfield(pagestart + 14, 3, "Landing Zone Cylinder");
bitfield(pagestart + 17, "RPL", 3, 0);
intfield(pagestart + 18, 1, "Rotational Offset");
intfield(pagestart + 20, 2, "Rotational Rate");
if (x_interface && replace)
return put_mode_page(mpi, cbuffer);
else
printf("\n");
return 0;
}
static int
common_disconnect_reconnect(struct mpage_info * mpi,
const char * prefix)
{
int status;
uint8_t *pagestart;
status = setup_mode_page(mpi, 11, cbuffer, &pagestart);
if (status)
return status;
if (prefix[0])
printf("%s", prefix);
if (!x_interface && !replace) {
printf("%s mode page (0x%x)\n", get_page_name(mpi), mpi->page);
printf("------------------------------------\n");
};
intfield(pagestart + 2, 1, "Buffer full ratio");
intfield(pagestart + 3, 1, "Buffer empty ratio");
intfield(pagestart + 4, 2, "Bus Inactivity Limit (SAS: 100us)");
intfield(pagestart + 6, 2, "Disconnect Time Limit");
intfield(pagestart + 8, 2, "Connect Time Limit (SAS: 100us)");
intfield(pagestart + 10, 2, "Maximum Burst Size");
bitfield(pagestart + 12, "EMDP", 1, 7);
bitfield(pagestart + 12, "Fair Arbitration (fcp:faa,fab,fac)", 0x7, 4);
bitfield(pagestart + 12, "DIMM", 1, 3);
bitfield(pagestart + 12, "DTDC", 0x7, 0);
intfield(pagestart + 14, 2, "First Burst Size");
if (x_interface && replace)
return put_mode_page(mpi, cbuffer);
else
printf("\n");
return 0;
}
static int
common_control(struct mpage_info * mpi, const char * prefix)
{
int status;
uint8_t *pagestart;
status = setup_mode_page(mpi, 21, cbuffer, &pagestart);
if (status)
return status;
if (prefix[0])
printf("%s", prefix);
if (!x_interface && !replace) {
printf("%s mode page (0x%x)\n", get_page_name(mpi), mpi->page);
printf("-----------------------\n");
}
bitfield(pagestart + 2, "TST", 0x7, 5);
bitfield(pagestart + 2, "TMF_ONLY", 1, 4);
bitfield(pagestart + 2, "D_SENSE", 1, 2);
bitfield(pagestart + 2, "GLTSD", 1, 1);
bitfield(pagestart + 2, "RLEC", 1, 0);
bitfield(pagestart + 3, "Queue Algorithm Modifier", 0xf, 4);
bitfield(pagestart + 3, "QErr", 0x3, 1);
bitfield(pagestart + 3, "DQue [obsolete]", 1, 0);
bitfield(pagestart + 4, "TAS", 1, 7);
bitfield(pagestart + 4, "RAC", 1, 6);
bitfield(pagestart + 4, "UA_INTLCK_CTRL", 0x3, 4);
bitfield(pagestart + 4, "SWP", 1, 3);
bitfield(pagestart + 4, "RAERP [obs.]", 1, 2);
bitfield(pagestart + 4, "UAAERP [obs.]", 1, 1);
bitfield(pagestart + 4, "EAERP [obs.]", 1, 0);
bitfield(pagestart + 5, "ATO", 1, 7);
bitfield(pagestart + 5, "TAS", 1, 6);
bitfield(pagestart + 5, "AUTOLOAD MODE", 0x7, 0);
intfield(pagestart + 6, 2, "Ready AER Holdoff Period [obs.]");
intfield(pagestart + 8, 2, "Busy Timeout Period");
intfield(pagestart + 10, 2, "Extended self-test completion time");
if (x_interface && replace)
return put_mode_page(mpi, cbuffer);
else
printf("\n");
return 0;
}
static int
common_control_extension(struct mpage_info * mpi, const char * prefix)
{
int status;
uint8_t *pagestart;
status = setup_mode_page(mpi, 4, cbuffer, &pagestart);
if (status)
return status;
if (prefix[0])
printf("%s", prefix);
if (!x_interface && !replace) {
printf("%s mode subpage (0x%x,0x%x)\n", get_page_name(mpi), mpi->page,
mpi->subpage);
printf("--------------------------------------------\n");
}
bitfield(pagestart + 4, "TCMOS", 1, 2);
bitfield(pagestart + 4, "SCSIP", 1, 1);
bitfield(pagestart + 4, "IALUAE", 1, 0);
bitfield(pagestart + 5, "Initial Priority", 0xf, 0);
if (x_interface && replace)
return put_mode_page(mpi, cbuffer);
else
printf("\n");
return 0;
}
static int
common_informational(struct mpage_info * mpi, const char * prefix)
{
int status;
uint8_t *pagestart;
status = setup_mode_page(mpi, 10, cbuffer, &pagestart);
if (status)
return status;
if (prefix[0])
printf("%s", prefix);
if (!x_interface && !replace) {
printf("%s mode page (0x%x)\n", get_page_name(mpi), mpi->page);
printf("-----------------------------------------\n");
}
bitfield(pagestart + 2, "PERF", 1, 7);
bitfield(pagestart + 2, "EBF", 1, 5);
bitfield(pagestart + 2, "EWASC", 1, 4);
bitfield(pagestart + 2, "DEXCPT", 1, 3);
bitfield(pagestart + 2, "TEST", 1, 2);
bitfield(pagestart + 2, "EBACKERR", 1, 1);
bitfield(pagestart + 2, "LOGERR", 1, 0);
bitfield(pagestart + 3, "MRIE", 0xf, 0);
intfield(pagestart + 4, 4, "Interval Timer");
intfield(pagestart + 8, 4, "Report Count");
if (x_interface && replace)
return put_mode_page(mpi, cbuffer);
else
printf("\n");
return 0;
}
static int
disk_error_recovery(struct mpage_info * mpi, const char * prefix)
{
int status;
uint8_t *pagestart;
status = setup_mode_page(mpi, 14, cbuffer, &pagestart);
if (status)
return status;
if (prefix[0])
printf("%s", prefix);
if (!x_interface && !replace) {
printf("%s mode page (0x%x)\n", get_page_name(mpi), mpi->page);
printf("-----------------------------------------\n");
}
bitfield(pagestart + 2, "AWRE", 1, 7);
bitfield(pagestart + 2, "ARRE", 1, 6);
bitfield(pagestart + 2, "TB", 1, 5);
bitfield(pagestart + 2, "RC", 1, 4);
bitfield(pagestart + 2, "EER", 1, 3);
bitfield(pagestart + 2, "PER", 1, 2);
bitfield(pagestart + 2, "DTE", 1, 1);
bitfield(pagestart + 2, "DCR", 1, 0);
intfield(pagestart + 3, 1, "Read Retry Count");
intfield(pagestart + 4, 1, "Correction Span");
intfield(pagestart + 5, 1, "Head Offset Count");
intfield(pagestart + 6, 1, "Data Strobe Offset Count");
intfield(pagestart + 8, 1, "Write Retry Count");
intfield(pagestart + 10, 2, "Recovery Time Limit (ms)");
if (x_interface && replace)
return put_mode_page(mpi, cbuffer);
else
printf("\n");
return 0;
}
static int
cdvd_error_recovery(struct mpage_info * mpi, const char * prefix)
{
int status;
uint8_t *pagestart;
status = setup_mode_page(mpi, 10, cbuffer, &pagestart);
if (status)
return status;
if (prefix[0])
printf("%s", prefix);
if (!x_interface && !replace) {
printf("%s mode page (0x%x)\n", get_page_name(mpi), mpi->page);
printf("------------------------------------------------\n");
}
bitfield(pagestart + 2, "AWRE", 1, 7);
bitfield(pagestart + 2, "ARRE", 1, 6);
bitfield(pagestart + 2, "TB", 1, 5);
bitfield(pagestart + 2, "RC", 1, 4);
bitfield(pagestart + 2, "PER", 1, 2);
bitfield(pagestart + 2, "DTE", 1, 1);
bitfield(pagestart + 2, "DCR", 1, 0);
intfield(pagestart + 3, 1, "Read Retry Count");
bitfield(pagestart + 7, "EMCDR", 3, 0);
intfield(pagestart + 8, 1, "Write Retry Count");
if (x_interface && replace)
return put_mode_page(mpi, cbuffer);
else
printf("\n");
return 0;
}
static int
cdvd_mrw(struct mpage_info * mpi, const char * prefix)
{
int status;
uint8_t *pagestart;
status = setup_mode_page(mpi, 1, cbuffer, &pagestart);
if (status)
return status;
if (prefix[0])
printf("%s", prefix);
if (!x_interface && !replace) {
printf("%s mode page (0x%x)\n", get_page_name(mpi), mpi->page);
printf("------------------------------------------------\n");
}
bitfield(pagestart + 3, "LBA space", 1, 0);
if (x_interface && replace)
return put_mode_page(mpi, cbuffer);
else
printf("\n");
return 0;
}
static int
disk_notch_parameters(struct mpage_info * mpi, const char * prefix)
{
int status;
uint8_t *pagestart;
status = setup_mode_page(mpi, 6, cbuffer, &pagestart);
if (status) {
fprintf(stdout, "Special case: only give 6 fields to '-XR' since"
" 'Pages Notched' is unchangeable\n");
return status;
}
if (prefix[0])
printf("%s", prefix);
if (!x_interface && !replace) {
printf("%s mode page (0x%x)\n", get_page_name(mpi), mpi->page);
printf("-----------------------------------\n");
};
bitfield(pagestart + 2, "Notched Drive", 1, 7);
bitfield(pagestart + 2, "Logical or Physical Notch", 1, 6);
intfield(pagestart + 4, 2, "Max # of notches");
intfield(pagestart + 6, 2, "Active Notch");
if (pagestart[2] & 0x40) {
intfield(pagestart + 8, 4, "Starting Boundary");
intfield(pagestart + 12, 4, "Ending Boundary");
} else { /* Hex is more meaningful for physical notches */
hexfield(pagestart + 8, 4, "Starting Boundary");
hexfield(pagestart + 12, 4, "Ending Boundary");
}
if (x_interface && !replace) {
#if 1
; /* do nothing, skip this field */
#else
if (1 == mpi->page_control) /* modifiable */
printf("0");
else
printf("0x%8.8x%8.8x", getnbyte(pagestart + 16, 4),
getnbyte(pagestart + 20, 4));
#endif
};
if (!x_interface)
printf("Pages Notched %8.8x %8.8x\n",
getnbyte(pagestart + 16, 4), getnbyte(pagestart + 20, 4));
if (x_interface && replace)
return put_mode_page(mpi, cbuffer);
else
printf("\n");
return 0;
}
static const char *
formatname(int format)
{
switch(format) {
case 0x0: return "logical block addresses (32 bit)";
case 0x3: return "logical block addresses (64 bit)";
case 0x4: return "bytes from index [Cyl:Head:Off]\n"
"Offset -1 marks whole track as bad.\n";
case 0x5: return "physical blocks [Cyl:Head:Sect]\n"
"Sector -1 marks whole track as bad.\n";
}
return "Weird, unknown format";
}
static int
read_defect_list(int grown_only)
{
int i, len, reallen, table, k, defect_format;
int status = 0;
int header = 1;
int sorthead = 0;
uint8_t cmd[10];
uint8_t cmd12[12];
uint8_t *df = NULL;
uint8_t *bp = NULL;
uint8_t *heapp = NULL;
unsigned int *headsp = NULL;
int trunc;
struct scsi_cmnd_io sci;
if (defectformat == HEAD_SORT_TOKEN) {
defectformat = 0x04;
sorthead = 1;
headsp = (unsigned int *)malloc(sizeof(unsigned int) * MAX_HEADS);
if (headsp == NULL) {
perror("malloc failed");
return status;
}
memset(headsp,0,sizeof(unsigned int) * MAX_HEADS);
}
for (table = grown_only; table < 2; table++) {
if (heapp) {
free(heapp);
heapp = NULL;
}
bp = cbuffer;
memset(bp, 0, 4);
trunc = 0;
reallen = -1;
cmd[0] = 0x37; /* READ DEFECT DATA (10) */
cmd[1] = 0x00;
cmd[2] = (table ? 0x08 : 0x10) | defectformat; /* List, Format */
cmd[3] = 0x00; /* (reserved) */
cmd[4] = 0x00; /* (reserved) */
cmd[5] = 0x00; /* (reserved) */
cmd[6] = 0x00; /* (reserved) */
cmd[7] = 0x00; /* Alloc len */
cmd[8] = 0x04; /* Alloc len (size finder) */
cmd[9] = 0x00; /* control */
sci.cmnd = cmd;
sci.cmnd_len = sizeof(cmd);
sci.dxfer_dir = DXFER_FROM_DEVICE;
sci.dxfer_len = 4;
sci.dxferp = bp;
i = do_scsi_io(&sci);
if (i) {
fprintf(stdout, ">>> Unable to read %s defect data.\n",
(table ? "grown (GLIST)" : "primary (PLIST)"));
status |= i;
continue;
}
if (trace_cmd > 1) {
printf(" cdb response:\n");
dump(bp, 4);
}
/*
* Check validity of response:
* bp[0] reserved, must be zero
* bp[1] bits 7-5 reserved, must be zero
* bp[1] bits 4-3 should match table requested
*/
if (0 != bp[0] || (table ? 0x08 : 0x10) != (bp[1] & 0xf8)) {
fprintf(stdout, ">>> Invalid header for %s defect list.\n",
(table ? "grown (GLIST)" : "primary (PLIST)"));
status |= 1;
continue;
}
if (header) {
printf("Defect Lists\n"
"------------\n");
header = 0;
}
len = (bp[2] << 8) + bp[3];
if (len < 0xfff8)
reallen = len;
else {
/*
* List length is at or over capacity of READ DEFECT DATA (10)
* Try to get actual length with READ DEFECT DATA (12)
*/
bp = cbuffer;
memset(bp, 0, 8);
cmd12[0] = 0xB7; /* READ DEFECT DATA (12) */
cmd12[1] = (table ? 0x08 : 0x10) | defectformat;/* List, Format */
cmd12[2] = 0x00; /* (reserved) */
cmd12[3] = 0x00; /* (reserved) */
cmd12[4] = 0x00; /* (reserved) */
cmd12[5] = 0x00; /* (reserved) */
cmd12[6] = 0x00; /* Alloc len */
cmd12[7] = 0x00; /* Alloc len */
cmd12[8] = 0x00; /* Alloc len */
cmd12[9] = 0x08; /* Alloc len (size finder) */
cmd12[10] = 0x00; /* reserved */
cmd12[11] = 0x00; /* control */
sci.cmnd = cmd12;
sci.cmnd_len = sizeof(cmd12);
sci.dxfer_dir = DXFER_FROM_DEVICE;
sci.dxfer_len = 8;
sci.dxferp = bp;
i = do_scsi_io(&sci);
if (i) {
if (trace_cmd) {
fprintf(stdout, ">>> No 12 byte command support, "
"but list is too long for 10 byte version.\n"
"List will be truncated at 8191 elements\n");
}
goto trytenbyte;
}
if (trace_cmd > 1) {
printf(" cdb response:\n");
dump(bp, 8);
}
/*
* Check validity of response:
* bp[0], bp[2] and bp[3] reserved, must be zero
* bp[1] bits 7-5 reserved, must be zero
* bp[1] bits 4-3 should match table we requested
*/
if (0 != bp[0] || 0 != bp[2] || 0 != bp[3] ||
((table ? 0x08 : 0x10) != (bp[1] & 0xf8))) {
if (trace_cmd)
fprintf(stdout,
">>> Invalid header for %s defect list.\n",
(table ? "grown (GLIST)" : "primary (PLIST)"));
goto trytenbyte;
}
len = (bp[4] << 24) + (bp[5] << 16) + (bp[6] << 8) + bp[7];
reallen = len;
}
if (len > 0) {
k = len + 8; /* length of defect list + header */
if (k > (int)sizeof(cbuffer)) {
heapp = (uint8_t *)malloc(k);
if (len > 0x80000 && NULL == heapp) {
len = 0x80000; /* go large: 512 KB */
k = len + 8;
heapp = (uint8_t *)malloc(k);
}
if (heapp != NULL)
bp = heapp;
}
if (len > 0xfff0 && heapp != NULL) {
cmd12[0] = 0xB7; /* READ DEFECT DATA (12) */
cmd12[1] = (table ? 0x08 : 0x10) | defectformat;
/* List, Format */
cmd12[2] = 0x00; /* (reserved) */
cmd12[3] = 0x00; /* (reserved) */
cmd12[4] = 0x00; /* (reserved) */
cmd12[5] = 0x00; /* (reserved) */
cmd12[6] = 0x00; /* Alloc len */
cmd12[7] = (k >> 16) & 0xff; /* Alloc len */
cmd12[8] = (k >> 8) & 0xff; /* Alloc len */
cmd12[9] = (k & 0xff); /* Alloc len */
cmd12[10] = 0x00; /* reserved */
cmd12[11] = 0x00; /* control */
sci.cmnd = cmd12;
sci.cmnd_len = sizeof(cmd12);
sci.dxfer_dir = DXFER_FROM_DEVICE;
sci.dxfer_len = k;
sci.dxferp = bp;
i = do_scsi_io(&sci);
if (i)
goto trytenbyte;
if (trace_cmd > 1) {
printf(" cdb response:\n");
dump(bp, 8);
}
reallen = (bp[4] << 24) + (bp[5] << 16) + (bp[6] << 8) +
bp[7];
if (reallen > len) {
trunc = 1;
}
df = (uint8_t *) (bp + 8);
}
else {
trytenbyte:
if (len > 0xfff8) {
len = 0xfff8;
trunc = 1;
}
k = len + 4; /* length of defect list + header */
if (k > (int)sizeof(cbuffer) && NULL == heapp) {
heapp = (uint8_t *)malloc(k);
if (heapp != NULL)
bp = heapp;
}
if (k > (int)sizeof(cbuffer) && NULL == heapp) {
bp = cbuffer;
k = sizeof(cbuffer);
len = k - 4;
trunc = 1;
}
cmd[0] = 0x37; /* READ DEFECT DATA (10) */
cmd[1] = 0x00;
cmd[2] = (table ? 0x08 : 0x10) | defectformat;
/* List, Format */
cmd[3] = 0x00; /* (reserved) */
cmd[4] = 0x00; /* (reserved) */
cmd[5] = 0x00; /* (reserved) */
cmd[6] = 0x00; /* (reserved) */
cmd[7] = (k >> 8); /* Alloc len */
cmd[8] = (k & 0xff); /* Alloc len */
cmd[9] = 0x00; /* control */
sci.cmnd = cmd;
sci.cmnd_len = sizeof(cmd);
sci.dxfer_dir = DXFER_FROM_DEVICE;
sci.dxfer_len = k;
sci.dxferp = bp;
i = do_scsi_io(&sci);
df = (uint8_t *) (bp + 4);
}
}
if (i) {
fprintf(stdout, ">>> Unable to read %s defect data.\n",
(table ? "grown (GLIST)" : "primary (PLIST)"));
status |= i;
continue;
}
else {
if (table && !status && !sorthead)
printf("\n");
defect_format = (bp[1] & 0x7);
if (-1 == reallen) {
printf("at least ");
reallen = len;
}
printf("%d entries (%d bytes) in %s table.\n",
reallen / ((0 == defect_format) ? 4 : 8), reallen,
table ? "grown (GLIST)" : "primary (PLIST)");
if (!sorthead)
printf("Format (%x) is: %s\n", defect_format,
formatname(defect_format));
i = 0;
switch (defect_format) {
case 4: /* bytes from index */
while (len > 0) {
snprintf((char *)cbuffer1, 40, "%6d:%3u:%8d",
getnbyte(df, 3), df[3], getnbyte(df + 4, 4));
if (sorthead == 0)
printf("%19s", (char *)cbuffer1);
else
if (df[3] < MAX_HEADS) headsp[df[3]]++;
len -= 8;
df += 8;
i++;
if (i >= 4 && !sorthead) {
printf("\n");
i = 0;
}
else if (!sorthead) printf("|");
}
case 5: /* physical sector */
while (len > 0) {
snprintf((char *)cbuffer1, 40, "%6d:%2u:%5d",
getnbyte(df, 3),
df[3], getnbyte(df + 4, 4));
if (sorthead == 0)
printf("%15s", (char *)cbuffer1);
else
if (df[3] < MAX_HEADS) headsp[df[3]]++;
len -= 8;
df += 8;
i++;
if (i >= 5 && !sorthead) {
printf("\n");
i = 0;
}
else if (!sorthead) printf("|");
}
case 0: /* lba (32 bit) */
while (len > 0) {
printf("%10d", getnbyte(df, 4));
len -= 4;
df += 4;
i++;
if (i >= 7) {
printf("\n");
i = 0;
}
else
printf("|");
}
case 3: /* lba (64 bit) */
while (len > 0) {
printf("%15" PRId64 , getnbyte_ll(df, 8));
len -= 8;
df += 8;
i++;
if (i >= 5) {
printf("\n");
i = 0;
}
else
printf("|");
}
break;
default:
printf("unknown defect list format: %d\n", defect_format);
break;
}
if (i && !sorthead)
printf("\n");
}
if (trunc)
printf("[truncated]\n");
}
if (heapp) {
free(heapp);
heapp = NULL;
}
if (sorthead) {
printf("Format is: [head:# entries for this head in list]\n\n");
for (i=0; i<MAX_HEADS; i++) {
if (headsp[i] > 0) {
printf("%3d: %u\n", i, headsp[i]);
}
}
}
printf("\n");
return status;
}
static int
disk_cache(struct mpage_info * mpi, const char * prefix)
{
int status;
uint8_t *pagestart;
status = setup_mode_page(mpi, 21, cbuffer, &pagestart);
if (status)
return status;
if (prefix[0])
printf("%s", prefix);
if (!x_interface && !replace) {
printf("%s mode page (0x%x)\n", get_page_name(mpi), mpi->page);
printf("-----------------------\n");
};
bitfield(pagestart + 2, "Initiator Control", 1, 7);
bitfield(pagestart + 2, "ABPF", 1, 6);
bitfield(pagestart + 2, "CAP", 1, 5);
bitfield(pagestart + 2, "DISC", 1, 4);
bitfield(pagestart + 2, "SIZE", 1, 3);
bitfield(pagestart + 2, "Write Cache Enabled", 1, 2);
bitfield(pagestart + 2, "MF", 1, 1);
bitfield(pagestart + 2, "Read Cache Disabled", 1, 0);
bitfield(pagestart + 3, "Demand Read Retention Priority", 0xf, 4);
bitfield(pagestart + 3, "Demand Write Retention Priority", 0xf, 0);
intfield(pagestart + 4, 2, "Disable Pre-fetch Transfer Length");
intfield(pagestart + 6, 2, "Minimum Pre-fetch");
intfield(pagestart + 8, 2, "Maximum Pre-fetch");
intfield(pagestart + 10, 2, "Maximum Pre-fetch Ceiling");
bitfield(pagestart + 12, "FSW", 1, 7);
bitfield(pagestart + 12, "LBCSS", 1, 6);
bitfield(pagestart + 12, "DRA", 1, 5);
bitfield(pagestart + 12, "NV_DIS", 1, 0);
intfield(pagestart + 13, 1, "Number of Cache Segments");
intfield(pagestart + 14, 2, "Cache Segment size");
intfield(pagestart + 17, 3, "Non-Cache Segment size");
if (x_interface && replace)
return put_mode_page(mpi, cbuffer);
else
printf("\n");
return 0;
}
static int
disk_format(struct mpage_info * mpi, const char * prefix)
{
int status;
uint8_t *pagestart;
status = setup_mode_page(mpi, 13, cbuffer, &pagestart);
if (status)
return status;
if (prefix[0])
printf("%s", prefix);
if (!x_interface && !replace) {
printf("%s mode page (0x%x)\n", get_page_name(mpi), mpi->page);
printf("-----------------------------\n");
};
intfield(pagestart + 2, 2, "Tracks per Zone");
intfield(pagestart + 4, 2, "Alternate sectors per zone");
intfield(pagestart + 6, 2, "Alternate tracks per zone");
intfield(pagestart + 8, 2, "Alternate tracks per lu");
intfield(pagestart + 10, 2, "Sectors per track");
intfield(pagestart + 12, 2, "Data bytes per physical sector");
intfield(pagestart + 14, 2, "Interleave");
intfield(pagestart + 16, 2, "Track skew factor");
intfield(pagestart + 18, 2, "Cylinder skew factor");
bitfield(pagestart + 20, "Supports Soft Sectoring", 1, 7);
bitfield(pagestart + 20, "Supports Hard Sectoring", 1, 6);
bitfield(pagestart + 20, "Removable Medium", 1, 5);
bitfield(pagestart + 20, "Surface", 1, 4);
if (x_interface && replace)
return put_mode_page(mpi, cbuffer);
else
printf("\n");
return 0;
}
static int
disk_verify_error_recovery(struct mpage_info * mpi, const char * prefix)
{
int status;
uint8_t *pagestart;
status = setup_mode_page(mpi, 7, cbuffer, &pagestart);
if (status)
return status;
if (prefix[0])
printf("%s", prefix);
if (!x_interface && !replace) {
printf("%s mode page (0x%x)\n", get_page_name(mpi), mpi->page);
printf("-------------------------------------\n");
}
bitfield(pagestart + 2, "EER", 1, 3);
bitfield(pagestart + 2, "PER", 1, 2);
bitfield(pagestart + 2, "DTE", 1, 1);
bitfield(pagestart + 2, "DCR", 1, 0);
intfield(pagestart + 3, 1, "Verify Retry Count");
intfield(pagestart + 4, 1, "Verify Correction Span (bits)");
intfield(pagestart + 10, 2, "Verify Recovery Time Limit (ms)");
if (x_interface && replace)
return put_mode_page(mpi, cbuffer);
else
printf("\n");
return 0;
}
#if 0
static int
peripheral_device_page(struct mpage_info * mpi, const char * prefix)
{
static char *idents[] =
{
"X3.131: Small Computer System Interface",
"X3.91M-1987: Storage Module Interface",
"X3.170: Enhanced Small Device Interface",
"X3.130-1986; X3T9.3/87-002: IPI-2",
"X3.132-1987; X3.147-1988: IPI-3"
};
int status;
unsigned ident;
uint8_t *pagestart;
char *name;
status = setup_mode_page(mpi, 2, cbuffer, &pagestart);
if (status)
return status;
if (prefix[0])
printf("%s", prefix);
if (!x_interface && !replace) {
printf("%s mode page (0x%x)\n", get_page_name(mpi), mpi->page);
printf("---------------------------------\n");
};
#if 0
dump(pagestart, 20);
pagestart[1] += 2; /*TEST */
cbuffer[8] += 2; /*TEST */
#endif
ident = getnbyte(pagestart + 2, 2);
if (ident < (sizeof(idents) / sizeof(char *)))
name = idents[ident];
else if (ident < 0x8000)
name = "Reserved";
else
name = "Vendor Specific";
#ifdef DPG_CHECK_THIS_OUT
bdlen = pagestart[1] - 6;
if (bdlen < 0)
bdlen = 0;
else {
status = setup_mode_page(mpi, 2, cbuffer, &bdlen,
&pagestart);
if (status)
return status;
}
hexfield(pagestart + 2, 2, "Interface Identifier");
if (!x_interface) {
for (ident = 0; ident < 35; ident++)
putchar(' ');
puts(name);
}
hexdatafield(pagestart + 8, bdlen, "Vendor Specific Data");
#endif
if (x_interface && replace)
return put_mode_page(mpi, cbuffer);
else
printf("\n");
if (x_interface)
puts(name);
return 0;
}
#endif
static int
common_power_condition(struct mpage_info * mpi, const char * prefix)
{
int status;
uint8_t *pagestart;
status = setup_mode_page(mpi, 4, cbuffer, &pagestart);
if (status)
return status;
if (prefix[0])
printf("%s", prefix);
if (!x_interface && !replace) {
printf("%s mode page (0x%x)\n", get_page_name(mpi), mpi->page);
printf("--------------------------------\n");
}
bitfield(pagestart + 3, "Idle", 1, 1);
bitfield(pagestart + 3, "Standby", 1, 0);
intfield(pagestart + 4, 4, "Idle Condition counter (100ms)");
intfield(pagestart + 8, 4, "Standby Condition counter (100ms)");
if (x_interface && replace)
return put_mode_page(mpi, cbuffer);
else
printf("\n");
return 0;
}
static int
disk_xor_control(struct mpage_info * mpi, const char * prefix)
{
int status;
uint8_t *pagestart;
status = setup_mode_page(mpi, 5, cbuffer, &pagestart);
if (status)
return status;
if (prefix[0])
printf("%s", prefix);
if (!x_interface && !replace) {
printf("%s mode page (0x%x)\n", get_page_name(mpi), mpi->page);
printf("--------------------------------\n");
}
bitfield(pagestart + 2, "XORDS", 1, 1);
intfield(pagestart + 4, 4, "Maximum XOR write size");
intfield(pagestart + 12, 4, "Maximum regenerate size");
intfield(pagestart + 16, 4, "Maximum rebuild transfer size");
intfield(pagestart + 22, 2, "Rebuild delay");
if (x_interface && replace)
return put_mode_page(mpi, cbuffer);
else
printf("\n");
return 0;
}
static int
disk_background(struct mpage_info * mpi, const char * prefix)
{
int status;
uint8_t *pagestart;
status = setup_mode_page(mpi, 4, cbuffer, &pagestart);
if (status)
return status;
if (prefix[0])
printf("%s", prefix);
if (!x_interface && !replace) {
printf("%s mode subpage (0x%x,0x%x)\n", get_page_name(mpi), mpi->page,
mpi->subpage);
printf("--------------------------------------------\n");
}
bitfield(pagestart + 4, "Enable background medium scan", 1, 0);
bitfield(pagestart + 5, "Enable pre-scan", 1, 0);
intfield(pagestart + 6, 2, "BMS interval time (hour)");
intfield(pagestart + 8, 2, "Pre-scan timeout value (hour)");
if (x_interface && replace)
return put_mode_page(mpi, cbuffer);
else
printf("\n");
return 0;
}
static int
optical_memory(struct mpage_info * mpi, const char * prefix)
{
int status;
uint8_t *pagestart;
status = setup_mode_page(mpi, 1, cbuffer, &pagestart);
if (status)
return status;
if (prefix[0])
printf("%s", prefix);
if (!x_interface && !replace) {
printf("%s mode page (0x%x)\n", get_page_name(mpi), mpi->page);
printf("--------------------------------\n");
}
bitfield(pagestart + 2, "RUBR", 1, 0);
if (x_interface && replace)
return put_mode_page(mpi, cbuffer);
else
printf("\n");
return 0;
}
static int
cdvd_write_param(struct mpage_info * mpi, const char * prefix)
{
int status;
uint8_t *pagestart;
status = setup_mode_page(mpi, 20, cbuffer, &pagestart);
if (status)
return status;
if (prefix[0])
printf("%s", prefix);
if (!x_interface && !replace) {
printf("%s mode page (0x%x)\n", get_page_name(mpi), mpi->page);
printf("--------------------------------\n");
}
bitfield(pagestart + 2, "BUFE", 1, 6);
bitfield(pagestart + 2, "LS_V", 1, 5);
bitfield(pagestart + 2, "Test Write", 1, 4);
bitfield(pagestart + 2, "Write Type", 0xf, 0);
bitfield(pagestart + 3, "MultiSession", 3, 6);
bitfield(pagestart + 3, "FP", 1, 5);
bitfield(pagestart + 3, "Copy", 1, 4);
bitfield(pagestart + 3, "Track Mode", 0xf, 0);
bitfield(pagestart + 4, "Data Block type", 0xf, 0);
intfield(pagestart + 5, 1, "Link size");
bitfield(pagestart + 7, "Initiator app. code", 0x3f, 0);
intfield(pagestart + 8, 1, "Session Format");
intfield(pagestart + 10, 4, "Packet size");
intfield(pagestart + 14, 2, "Audio Pause Length");
hexdatafield(pagestart + 16, 16, "Media Catalog number");
hexdatafield(pagestart + 32, 16, "Int. standard recording code");
hexdatafield(pagestart + 48, 1, "Subheader byte 1");
hexdatafield(pagestart + 49, 1, "Subheader byte 2");
hexdatafield(pagestart + 50, 1, "Subheader byte 3");
hexdatafield(pagestart + 51, 1, "Subheader byte 4");
if (x_interface && replace)
return put_mode_page(mpi, cbuffer);
else
printf("\n");
return 0;
}
static int
cdvd_audio_control(struct mpage_info * mpi, const char * prefix)
{
int status;
uint8_t *pagestart;
status = setup_mode_page(mpi, 10, cbuffer, &pagestart);
if (status)
return status;
if (prefix[0])
printf("%s", prefix);
if (!x_interface && !replace) {
printf("%s mode page (0x%x)\n", get_page_name(mpi), mpi->page);
printf("--------------------------------\n");
}
bitfield(pagestart + 2, "IMMED", 1, 2);
bitfield(pagestart + 2, "SOTC", 1, 1);
bitfield(pagestart + 8, "CDDA out port 0, channel select", 0xf, 0);
intfield(pagestart + 9, 1, "Channel port 0 volume");
bitfield(pagestart + 10, "CDDA out port 1, channel select", 0xf, 0);
intfield(pagestart + 11, 1, "Channel port 1 volume");
bitfield(pagestart + 12, "CDDA out port 2, channel select", 0xf, 0);
intfield(pagestart + 13, 1, "Channel port 2 volume");
bitfield(pagestart + 14, "CDDA out port 3, channel select", 0xf, 0);
intfield(pagestart + 15, 1, "Channel port 3 volume");
if (x_interface && replace)
return put_mode_page(mpi, cbuffer);
else
printf("\n");
return 0;
}
static int
cdvd_timeout(struct mpage_info * mpi, const char * prefix)
{
int status;
uint8_t *pagestart;
status = setup_mode_page(mpi, 6, cbuffer, &pagestart);
if (status)
return status;
if (prefix[0])
printf("%s", prefix);
if (!x_interface && !replace) {
printf("%s mode page (0x%x)\n", get_page_name(mpi), mpi->page);
printf("-----------------------------------\n");
}
bitfield(pagestart + 4, "G3Enable", 1, 3);
bitfield(pagestart + 4, "TMOE", 1, 2);
bitfield(pagestart + 4, "DISP", 1, 1);
bitfield(pagestart + 4, "SWPP", 1, 0);
intfield(pagestart + 6, 2, "Group 1 minimum time-out");
intfield(pagestart + 8, 2, "Group 2 minimum time-out");
if (x_interface && replace)
return put_mode_page(mpi, cbuffer);
else
printf("\n");
return 0;
}
static int
cdvd_device_param(struct mpage_info * mpi, const char * prefix)
{
int status;
uint8_t *pagestart;
status = setup_mode_page(mpi, 3, cbuffer, &pagestart);
if (status)
return status;
if (prefix[0])
printf("%s", prefix);
if (!x_interface && !replace) {
printf("%s mode page (0x%x)\n", get_page_name(mpi), mpi->page);
printf("------------------------------------\n");
}
bitfield(pagestart + 3, "Inactivity timer multiplier", 0xf, 0);
intfield(pagestart + 4, 2, "MSF-S units per MSF_M unit");
intfield(pagestart + 6, 2, "MSF-F units per MSF_S unit");
if (x_interface && replace)
return put_mode_page(mpi, cbuffer);
else
printf("\n");
return 0;
}
/* This is not a standard t10.org MMC mode page (it is now "protocol specific
lu" mode page). This definition was found in Hitachi GF-2050/GF-2055
DVD-RAM drive SCSI reference manual. */
static int
cdvd_feature(struct mpage_info * mpi, const char * prefix)
{
int status;
uint8_t *pagestart;
status = setup_mode_page(mpi, 12, cbuffer, &pagestart);
if (status)
return status;
if (prefix[0])
printf("%s", prefix);
if (!x_interface && !replace) {
printf("%s mode page (0x%x)\n", get_page_name(mpi), mpi->page);
printf("----------------------------------------------\n");
}
intfield(pagestart + 2, 2, "DVD feature set");
intfield(pagestart + 4, 2, "CD audio");
intfield(pagestart + 6, 2, "Embedded changer");
intfield(pagestart + 8, 2, "Packet SMART");
intfield(pagestart + 10, 2, "Persistent prevent(MESN)");
intfield(pagestart + 12, 2, "Event status notification");
intfield(pagestart + 14, 2, "Digital output");
intfield(pagestart + 16, 2, "CD sequential recordable");
intfield(pagestart + 18, 2, "DVD sequential recordable");
intfield(pagestart + 20, 2, "Random recordable");
intfield(pagestart + 22, 2, "Key management");
intfield(pagestart + 24, 2, "Partial recorded CD media read");
if (x_interface && replace)
return put_mode_page(mpi, cbuffer);
else
printf("\n");
return 0;
}
static int
cdvd_mm_capab(struct mpage_info * mpi, const char * prefix)
{
int status;
uint8_t *pagestart;
status = setup_mode_page(mpi, 49, cbuffer, &pagestart);
if (status)
return status;
if (prefix[0])
printf("%s", prefix);
if (!x_interface && !replace) {
printf("%s mode page (0x%x)\n", get_page_name(mpi), mpi->page);
printf("----------------------------------------------------\n");
}
bitfield(pagestart + 2, "DVD-RAM read", 1, 5);
bitfield(pagestart + 2, "DVD-R read", 1, 4);
bitfield(pagestart + 2, "DVD-ROM read", 1, 3);
bitfield(pagestart + 2, "Method 2", 1, 2);
bitfield(pagestart + 2, "CD-RW read", 1, 1);
bitfield(pagestart + 2, "CD-R read", 1, 0);
bitfield(pagestart + 3, "DVD-RAM write", 1, 5);
bitfield(pagestart + 3, "DVD-R write", 1, 4);
bitfield(pagestart + 3, "DVD-ROM write", 1, 3);
bitfield(pagestart + 3, "Test Write", 1, 2);
bitfield(pagestart + 3, "CD-RW write", 1, 1);
bitfield(pagestart + 3, "CD-R write", 1, 0);
bitfield(pagestart + 4, "BUF", 1, 7);
bitfield(pagestart + 4, "MultiSession", 1, 6);
bitfield(pagestart + 4, "Mode 2 Form 2", 1, 5);
bitfield(pagestart + 4, "Mode 2 Form 1", 1, 4);
bitfield(pagestart + 4, "Digital port (2)", 1, 3);
bitfield(pagestart + 4, "Digital port (1)", 1, 2);
bitfield(pagestart + 4, "Composite", 1, 1);
bitfield(pagestart + 4, "Audio play", 1, 0);
bitfield(pagestart + 5, "Read bar code", 1, 7);
bitfield(pagestart + 5, "UPC", 1, 6);
bitfield(pagestart + 5, "ISRC", 1, 5);
bitfield(pagestart + 5, "C2 pointers supported", 1, 4);
bitfield(pagestart + 5, "R-W de-interleaved & corrected", 1, 3);
bitfield(pagestart + 5, "R-W supported", 1, 2);
bitfield(pagestart + 5, "CD-DA stream is accurate", 1, 1);
bitfield(pagestart + 5, "CD-DA commands supported", 1, 0);
bitfield(pagestart + 6, "Loading mechanism type", 7, 5);
bitfield(pagestart + 6, "Eject (individual or magazine)", 1, 3);
bitfield(pagestart + 6, "Prevent jumper", 1, 2);
bitfield(pagestart + 6, "Lock state", 1, 1);
bitfield(pagestart + 6, "Lock", 1, 0);
bitfield(pagestart + 7, "R-W in lead-in", 1, 5);
bitfield(pagestart + 7, "Side change capable", 1, 4);
bitfield(pagestart + 7, "S/W slot selection", 1, 3);
bitfield(pagestart + 7, "Changer supports disc present", 1, 2);
bitfield(pagestart + 7, "Separate channel mute", 1, 1);
bitfield(pagestart + 7, "Separate volume levels", 1, 0);
intfield(pagestart + 10, 2, "number of volume level supported");
intfield(pagestart + 12, 2, "Buffer size supported");
bitfield(pagestart + 17, "Length", 3, 4);
bitfield(pagestart + 17, "LSBF", 1, 3);
bitfield(pagestart + 17, "RCK", 1, 2);
bitfield(pagestart + 17, "BCKF", 1, 1);
intfield(pagestart + 22, 2, "Copy management revision supported");
bitfield(pagestart + 27, "Rotation control selected", 3, 0);
intfield(pagestart + 28, 2, "Current write speed selected");
intfield(pagestart + 30, 2, "# of lu speed performance tables");
if (x_interface && replace)
return put_mode_page(mpi, cbuffer);
else
printf("\n");
return 0;
}
static int
cdvd_cache(struct mpage_info * mpi, const char * prefix)
{
int status;
uint8_t *pagestart;
status = setup_mode_page(mpi, 2, cbuffer, &pagestart);
if (status)
return status;
if (prefix[0])
printf("%s", prefix);
if (!x_interface && !replace) {
printf("%s mode page (0x%x)\n", get_page_name(mpi), mpi->page);
printf("-----------------------\n");
};
bitfield(pagestart + 2, "Write Cache Enabled", 1, 2);
bitfield(pagestart + 2, "Read Cache Disabled", 1, 0);
if (x_interface && replace)
return put_mode_page(mpi, cbuffer);
else
printf("\n");
return 0;
}
static int
tape_data_compression(struct mpage_info * mpi, const char * prefix)
{
int status;
uint8_t *pagestart;
status = setup_mode_page(mpi, 6, cbuffer, &pagestart);
if (status)
return status;
if (prefix[0])
printf("%s", prefix);
if (!x_interface && !replace) {
printf("%s mode page (0x%x)\n", get_page_name(mpi), mpi->page);
printf("----------------------------------------------------\n");
}
bitfield(pagestart + 2, "DCE", 1, 7);
bitfield(pagestart + 2, "DCC", 1, 6);
bitfield(pagestart + 3, "DDE", 1, 7);
bitfield(pagestart + 3, "RED", 3, 5);
intfield(pagestart + 4, 4, "Compression algorithm");
intfield(pagestart + 8, 4, "Decompression algorithm");
if (x_interface && replace)
return put_mode_page(mpi, cbuffer);
else
printf("\n");
return 0;
}
static int
tape_dev_config(struct mpage_info * mpi, const char * prefix)
{
int status;
uint8_t *pagestart;
status = setup_mode_page(mpi, 25, cbuffer, &pagestart);
if (status)
return status;
if (prefix[0])
printf("%s", prefix);
if (!x_interface && !replace) {
printf("%s mode page (0x%x)\n", get_page_name(mpi), mpi->page);
printf("----------------------------------------------------\n");
}
bitfield(pagestart + 2, "CAF", 1, 5);
bitfield(pagestart + 2, "Active format", 0x1f, 0);
intfield(pagestart + 3, 1, "Active partition");
intfield(pagestart + 4, 1, "Write object cbuffer full ratio");
intfield(pagestart + 5, 1, "Read object cbuffer full ratio");
intfield(pagestart + 6, 2, "Wire delay time");
bitfield(pagestart + 8, "OBR", 1, 7);
bitfield(pagestart + 8, "LOIS", 1, 6);
bitfield(pagestart + 8, "RSMK", 1, 5);
bitfield(pagestart + 8, "AVC", 1, 4);
bitfield(pagestart + 8, "SOCF", 3, 2);
bitfield(pagestart + 8, "ROBO", 1, 1);
bitfield(pagestart + 8, "REW", 1, 0);
intfield(pagestart + 9, 1, "Gap size");
bitfield(pagestart + 10, "EOD defined", 7, 5);
bitfield(pagestart + 10, "EEG", 1, 4);
bitfield(pagestart + 10, "SEW", 1, 3);
bitfield(pagestart + 10, "SWP", 1, 2);
bitfield(pagestart + 10, "BAML", 1, 1);
bitfield(pagestart + 10, "BAM", 1, 0);
intfield(pagestart + 11, 3, "Object cbuffer size at early warning");
intfield(pagestart + 14, 1, "Select data compression algorithm");
bitfield(pagestart + 15, "ASOCWP", 1, 2);
bitfield(pagestart + 15, "PERSWO", 1, 1);
bitfield(pagestart + 15, "PRMWP", 1, 0);
if (x_interface && replace)
return put_mode_page(mpi, cbuffer);
else
printf("\n");
return 0;
}
static int
tape_medium_part1(struct mpage_info * mpi, const char * prefix)
{
int status, off, len;
uint8_t *pagestart;
/* variable length mode page, need to know its response length */
status = get_mode_page(mpi, 0, cbuffer);
if (status)
return status;
off = modePageOffset(cbuffer, mpi->resp_len, mode6byte);
if (off < 0)
return off;
len = mpi->resp_len - off;
status = setup_mode_page(mpi, 12 + ((len - 10) / 2), cbuffer, &pagestart);
if (status)
return status;
if (prefix[0])
printf("%s", prefix);
if (!x_interface && !replace) {
printf("%s mode page (0x%x)\n", get_page_name(mpi), mpi->page);
printf("----------------------------------------------------\n");
}
intfield(pagestart + 2, 1, "Maximum additional partitions");
intfield(pagestart + 3, 1, "Additional partitions defined");
bitfield(pagestart + 4, "FDP", 1, 7);
bitfield(pagestart + 4, "SDP", 1, 6);
bitfield(pagestart + 4, "IDP", 1, 5);
bitfield(pagestart + 4, "PSUM", 3, 3);
bitfield(pagestart + 4, "POFM", 1, 2);
bitfield(pagestart + 4, "CLEAR", 1, 1);
bitfield(pagestart + 4, "ADDP", 1, 0);
intfield(pagestart + 5, 1, "Medium format recognition");
bitfield(pagestart + 6, "Partition units", 0xf, 0);
intfield(pagestart + 8, 2, "Partition size");
for (off = 10; off < len; off += 2)
intfield(pagestart + off, 2, "Partition size");
if (x_interface && replace)
return put_mode_page(mpi, cbuffer);
else
printf("\n");
return 0;
}
static int
tape_medium_part2_4(struct mpage_info * mpi, const char * prefix)
{
int status, off, len;
uint8_t *pagestart;
/* variable length mode page, need to know its response length */
status = get_mode_page(mpi, 0, cbuffer);
if (status)
return status;
off = modePageOffset(cbuffer, mpi->resp_len, mode6byte);
if (off < 0)
return off;
len = mpi->resp_len - off;
status = setup_mode_page(mpi, 1 + ((len - 4) / 2), cbuffer, &pagestart);
if (status)
return status;
if (prefix[0])
printf("%s", prefix);
if (!x_interface && !replace) {
printf("%s mode page (0x%x)\n", get_page_name(mpi), mpi->page);
printf("----------------------------------------------------\n");
}
intfield(pagestart + 2, 2, "Partition size");
for (off = 4; off < len; off += 2)
intfield(pagestart + off, 2, "Partition size");
if (x_interface && replace)
return put_mode_page(mpi, cbuffer);
else
printf("\n");
return 0;
}
static int
ses_services_manag(struct mpage_info * mpi, const char * prefix)
{
int status;
uint8_t *pagestart;
status = setup_mode_page(mpi, 2, cbuffer, &pagestart);
if (status)
return status;
if (prefix[0])
printf("%s", prefix);
if (!x_interface && !replace) {
printf("%s mode page (0x%x)\n", get_page_name(mpi), mpi->page);
printf("----------------------------------------------------\n");
}
bitfield(pagestart + 5, "ENBLTC", 1, 0);
intfield(pagestart + 6, 2, "Maximum time to completion (100 ms units)");
if (x_interface && replace)
return put_mode_page(mpi, cbuffer);
else
printf("\n");
return 0;
}
static int
fcp_proto_spec_lu(struct mpage_info * mpi, const char * prefix)
{
int status;
uint8_t *pagestart;
status = setup_mode_page(mpi, 1, cbuffer, &pagestart);
if (status)
return status;
if (prefix[0])
printf("%s", prefix);
if (!x_interface && !replace) {
printf("%s mode page (0x%x)\n", "Fibre Channel logical unit",
mpi->page);
printf("----------------------------------------------------\n");
}
bitfield(pagestart + 3, "EPDC", 1, 0);
if (x_interface && replace)
return put_mode_page(mpi, cbuffer);
else
printf("\n");
return 0;
}
static int
sas_proto_spec_lu(struct mpage_info * mpi, const char * prefix)
{
int status;
uint8_t *pagestart;
status = setup_mode_page(mpi, 1, cbuffer, &pagestart);
if (status)
return status;
if (prefix[0])
printf("%s", prefix);
if (!x_interface && !replace) {
printf("%s mode page (0x%x)\n", "SAS logical unit", mpi->page);
printf("----------------------------------------------------\n");
}
bitfield(pagestart + 2, "Transport Layer Retries", 1, 4);
if (x_interface && replace)
return put_mode_page(mpi, cbuffer);
else
printf("\n");
return 0;
}
static int
common_proto_spec_lu(struct mpage_info * mpi, const char * prefix)
{
int status;
int proto_id = 0;
status = get_protocol_id(0, cbuffer, &proto_id, NULL);
if (status)
return status;
if (0 == proto_id)
return fcp_proto_spec_lu(mpi, prefix);
else if (6 == proto_id)
return sas_proto_spec_lu(mpi, prefix);
else
return DECODE_FAILED_TRY_HEX;
}
static int
fcp_proto_spec_port(struct mpage_info * mpi, const char * prefix)
{
int status;
uint8_t *pagestart;
status = setup_mode_page(mpi, 10, cbuffer, &pagestart);
if (status)
return status;
if (prefix[0])
printf("%s", prefix);
if (!x_interface && !replace) {
printf("%s mode page (0x%x)\n", "Fibre Channel port control",
mpi->page);
printf("----------------------------------------------------\n");
}
bitfield(pagestart + 3, "DTFD", 1, 7);
bitfield(pagestart + 3, "PLPB", 1, 6);
bitfield(pagestart + 3, "DDIS", 1, 5);
bitfield(pagestart + 3, "DLM", 1, 4);
bitfield(pagestart + 3, "RHA", 1, 3);
bitfield(pagestart + 3, "ALWI", 1, 2);
bitfield(pagestart + 3, "DTIPE", 1, 1);
bitfield(pagestart + 3, "DTOLI", 1, 0);
bitfield(pagestart + 6, "RR_TOV units", 7, 0);
intfield(pagestart + 7, 1, "Resource recovery time-out");
if (x_interface && replace)
return put_mode_page(mpi, cbuffer);
else
printf("\n");
return 0;
}
static int
spi4_proto_spec_port(struct mpage_info * mpi, const char * prefix)
{
int status;
uint8_t *pagestart;
status = setup_mode_page(mpi, 1, cbuffer, &pagestart);
if (status)
return status;
if (prefix[0])
printf("%s", prefix);
if (!x_interface && !replace) {
printf("%s mode page (0x%x)\n", "SPI-4 port control", mpi->page);
printf("-----------------------------------\n");
}
intfield(pagestart + 4, 2, "Synchronous transfer time-out");
if (x_interface && replace)
return put_mode_page(mpi, cbuffer);
else
printf("\n");
return 0;
}
/* Protocol specific mode page for SAS, short format (subpage 0) */
static int
sas_proto_spec_port(struct mpage_info * mpi, const char * prefix)
{
int status;
uint8_t *pagestart;
status = setup_mode_page(mpi, 3, cbuffer, &pagestart);
if (status)
return status;
if (prefix[0])
printf("%s", prefix);
if (!x_interface && !replace) {
printf("%s mode page (0x%x)\n", "SAS SSP port control", mpi->page);
printf("-------------------------------------\n");
}
bitfield(pagestart + 2, "Ready LED meaning", 0x1, 4);
intfield(pagestart + 4, 2, "I_T Nexus Loss time");
intfield(pagestart + 6, 2, "Initiator response time-out");
if (x_interface && replace)
return put_mode_page(mpi, cbuffer);
else
printf("\n");
return 0;
}
static int
common_proto_spec_port(struct mpage_info * mpi, const char * prefix)
{
int status;
int proto_id = 0;
status = get_protocol_id(1, cbuffer, &proto_id, NULL);
if (status)
return status;
if (0 == proto_id)
return fcp_proto_spec_port(mpi, prefix);
else if (1 == proto_id)
return spi4_proto_spec_port(mpi, prefix);
else if (6 == proto_id)
return sas_proto_spec_port(mpi, prefix);
else
return DECODE_FAILED_TRY_HEX;
}
static int
spi4_margin_control(struct mpage_info * mpi, const char * prefix)
{
int status;
uint8_t *pagestart;
status = setup_mode_page(mpi, 5, cbuffer, &pagestart);
if (status)
return status;
if (prefix[0])
printf("%s", prefix);
if (!x_interface && !replace) {
printf("%s mode subpage (0x%x,0x%x)\n", "SPI-4 Margin control",
mpi->page, mpi->subpage);
printf("--------------------------------------------\n");
}
bitfield(pagestart + 5, "Protocol identifier", 0xf, 0);
bitfield(pagestart + 7, "Driver Strength", 0xf, 4);
bitfield(pagestart + 8, "Driver Asymmetry", 0xf, 4);
bitfield(pagestart + 8, "Driver Precompensation", 0xf, 0);
bitfield(pagestart + 9, "Driver Slew rate", 0xf, 4);
if (x_interface && replace)
return put_mode_page(mpi, cbuffer);
else
printf("\n");
return 0;
}
/* Protocol specific mode page for SAS, phy control + discover (subpage 1) */
static int
sas_phy_control_discover(struct mpage_info * mpi, const char * prefix)
{
int status, off, num_phys, k;
uint8_t *pagestart;
uint8_t *p;
/* variable length mode page, need to know its response length */
status = get_mode_page(mpi, 0, cbuffer);
if (status)
return status;
off = modePageOffset(cbuffer, mpi->resp_len, mode6byte);
if (off < 0)
return off;
num_phys = cbuffer[off + 7];
status = setup_mode_page(mpi, 1 + (16 * num_phys), cbuffer, &pagestart);
if (status)
return status;
if (prefix[0])
printf("%s", prefix);
if (!x_interface && !replace) {
printf("%s mode subpage (0x%x,0x%x)\n", "SAS Phy Control and "
"Discover", mpi->page, mpi->subpage);
printf("--------------------------------------------\n");
}
intfield(pagestart + 7, 1, "Number of phys");
for (k = 0, p = pagestart + 8; k < num_phys; ++k, p += 48) {
intfield(p + 1, 1, "Phy Identifier");
bitfield(p + 4, "Attached Device type", 0x7, 4);
bitfield(p + 5, "Negotiated Logical Link rate", 0xf, 0);
bitfield(p + 6, "Attached SSP Initiator port", 0x1, 3);
bitfield(p + 6, "Attached STP Initiator port", 0x1, 2);
bitfield(p + 6, "Attached SMP Initiator port", 0x1, 1);
bitfield(p + 7, "Attached SSP Target port", 0x1, 3);
bitfield(p + 7, "Attached STP Target port", 0x1, 2);
bitfield(p + 7, "Attached SMP Target port", 0x1, 1);
hexdatafield(p + 8, 8, "SAS address");
hexdatafield(p + 16, 8, "Attached SAS address");
intfield(p + 24, 1, "Attached Phy identifier");
bitfield(p + 32, "Programmed Min Physical Link rate", 0xf, 4);
bitfield(p + 32, "Hardware Min Physical Link rate", 0xf, 0);
bitfield(p + 33, "Programmed Max Physical Link rate", 0xf, 4);
bitfield(p + 33, "Hardware Max Physical Link rate", 0xf, 0);
}
if (x_interface && replace)
return put_mode_page(mpi, cbuffer);
else
printf("\n");
return 0;
}
static int
common_proto_spec_port_sp1(struct mpage_info * mpi, const char * prefix)
{
int status;
int proto_id = 0;
status = get_protocol_id(1, cbuffer, &proto_id, NULL);
if (status)
return status;
if (1 == proto_id)
return spi4_margin_control(mpi, prefix);
else if (6 == proto_id)
return sas_phy_control_discover(mpi, prefix);
else
return DECODE_FAILED_TRY_HEX;
}
static int
spi4_training_config(struct mpage_info * mpi, const char * prefix)
{
int status;
uint8_t *pagestart;
status = setup_mode_page(mpi, 27, cbuffer, &pagestart);
if (status)
return status;
if (prefix[0])
printf("%s", prefix);
if (!x_interface && !replace) {
printf("%s mode subpage (0x%x,0x%x)\n", "training configuration",
mpi->page, mpi->subpage);
printf("----------------------------------------------------------\n");
}
hexdatafield(pagestart + 10, 4, "DB(0) value");
hexdatafield(pagestart + 14, 4, "DB(1) value");
hexdatafield(pagestart + 18, 4, "DB(2) value");
hexdatafield(pagestart + 22, 4, "DB(3) value");
hexdatafield(pagestart + 26, 4, "DB(4) value");
hexdatafield(pagestart + 30, 4, "DB(5) value");
hexdatafield(pagestart + 34, 4, "DB(6) value");
hexdatafield(pagestart + 38, 4, "DB(7) value");
hexdatafield(pagestart + 42, 4, "DB(8) value");
hexdatafield(pagestart + 46, 4, "DB(9) value");
hexdatafield(pagestart + 50, 4, "DB(10) value");
hexdatafield(pagestart + 54, 4, "DB(11) value");
hexdatafield(pagestart + 58, 4, "DB(12) value");
hexdatafield(pagestart + 62, 4, "DB(13) value");
hexdatafield(pagestart + 66, 4, "DB(14) value");
hexdatafield(pagestart + 70, 4, "DB(15) value");
hexdatafield(pagestart + 74, 4, "P_CRCA value");
hexdatafield(pagestart + 78, 4, "P1 value");
hexdatafield(pagestart + 82, 4, "BSY value");
hexdatafield(pagestart + 86, 4, "SEL value");
hexdatafield(pagestart + 90, 4, "RST value");
hexdatafield(pagestart + 94, 4, "REQ value");
hexdatafield(pagestart + 98, 4, "ACK value");
hexdatafield(pagestart + 102, 4, "ATN value");
hexdatafield(pagestart + 106, 4, "C/D value");
hexdatafield(pagestart + 110, 4, "I/O value");
hexdatafield(pagestart + 114, 4, "MSG value");
if (x_interface && replace)
return put_mode_page(mpi, cbuffer);
else
printf("\n");
return 0;
}
/* SAS(2) SSP, shared protocol specific port mode subpage (subpage 2) */
static int
sas_shared_spec_port(struct mpage_info * mpi, const char * prefix)
{
int status;
uint8_t *pagestart;
status = setup_mode_page(mpi, 1, cbuffer, &pagestart);
if (status)
return status;
if (prefix[0])
printf("%s", prefix);
if (!x_interface && !replace) {
printf("%s mode subpage (0x%x,0x%x)\n", "SAS SSP shared protocol "
"specific port", mpi->page, mpi->subpage);
printf("-----------------------------------------------------\n");
}
intfield(pagestart + 6, 2, "Power loss timeout(ms)");
if (x_interface && replace)
return put_mode_page(mpi, cbuffer);
else
printf("\n");
return 0;
}
static int
common_proto_spec_port_sp2(struct mpage_info * mpi, const char * prefix)
{
int status;
int proto_id = 0;
status = get_protocol_id(1, cbuffer, &proto_id, NULL);
if (status)
return status;
if (1 == proto_id)
return spi4_training_config(mpi, prefix);
else if (6 == proto_id)
return sas_shared_spec_port(mpi, prefix);
else
return DECODE_FAILED_TRY_HEX;
}
static int
spi4_negotiated(struct mpage_info * mpi, const char * prefix)
{
int status;
uint8_t *pagestart;
status = setup_mode_page(mpi, 7, cbuffer, &pagestart);
if (status)
return status;
if (prefix[0])
printf("%s", prefix);
if (!x_interface && !replace) {
printf("%s mode subpage (0x%x,0x%x)\n", get_page_name(mpi), mpi->page,
mpi->subpage);
printf("--------------------------------------------\n");
}
intfield(pagestart + 6, 1, "Transfer period");
intfield(pagestart + 8, 1, "REQ/ACK offset");
intfield(pagestart + 9, 1, "Transfer width exponent");
bitfield(pagestart + 10, "Protocol option bits", 0x7f, 0);
bitfield(pagestart + 11, "Transceiver mode", 3, 2);
bitfield(pagestart + 11, "Sent PCOMP_EN", 1, 1);
bitfield(pagestart + 11, "Received PCOMP_EN", 1, 0);
if (x_interface && replace)
return put_mode_page(mpi, cbuffer);
else
printf("\n");
return 0;
}
static int
spi4_report_xfer(struct mpage_info * mpi, const char * prefix)
{
int status;
uint8_t *pagestart;
status = setup_mode_page(mpi, 4, cbuffer, &pagestart);
if (status)
return status;
if (prefix[0])
printf("%s", prefix);
if (!x_interface && !replace) {
printf("%s mode subpage (0x%x,0x%x)\n", get_page_name(mpi), mpi->page,
mpi->subpage);
printf("--------------------------------------------\n");
}
intfield(pagestart + 6, 1, "Mimimum transfer period factor");
intfield(pagestart + 8, 1, "Maximum REQ/ACK offset");
intfield(pagestart + 9, 1, "Maximum transfer width exponent");
bitfield(pagestart + 10, "Protocol option bits supported", 0xff, 0);
if (x_interface && replace)
return put_mode_page(mpi, cbuffer);
else
printf("\n");
return 0;
}
static void
print_hex_page(struct mpage_info * mpi, const char * prefix,
uint8_t *pagestart, int off, int len)
{
int k;
const char * pg_name;
if (prefix[0])
printf("%s", prefix);
if (! x_interface) {
pg_name = get_page_name(mpi);
if (mpi->subpage) {
if (pg_name && (unkn_page_str != pg_name))
printf("mode page: 0x%02x subpage: 0x%02x [%s]\n",
mpi->page, mpi->subpage, pg_name);
else
printf("mode page: 0x%02x subpage: 0x%02x\n", mpi->page,
mpi->subpage);
printf("------------------------------\n");
} else {
if (pg_name && (unkn_page_str != pg_name))
printf("mode page: 0x%02x [%s]\n", mpi->page,
pg_name);
else
printf("mode page: 0x%02x\n", mpi->page);
printf("---------------\n");
}
}
for (k = off; k < len; k++)
{
char nm[8];
snprintf(nm, sizeof(nm), "0x%02x", k);
hexdatafield(pagestart + k, 1, nm);
}
printf("\n");
}
static int
do_user_page(struct mpage_info * mpi, int decode_in_hex)
{
int status = 0;
int len, off, res, done;
int offset = 0;
uint8_t *pagestart;
char prefix[96];
struct mpage_info local_mp_i;
struct mpage_name_func * mpf;
int multiple = ((MP_LIST_PAGES == mpi->page) ||
(MP_LIST_SUBPAGES == mpi->subpage));
if (replace && multiple) {
printf("Can't list all (sub)pages and use replace (-R) together\n");
return 1;
}
status = get_mode_page(mpi, 0, cbuffer2);
if (status) {
printf("\n");
return status;
} else {
offset = modePageOffset(cbuffer2, mpi->resp_len, mode6byte);
if (offset < 0) {
fprintf(stdout, "mode page=0x%x has bad page format\n",
mpi->page);
fprintf(stdout, " perhaps '-z' switch may help\n");
return -1;
}
pagestart = cbuffer2 + offset;
}
memset(&local_mp_i, 0, sizeof(local_mp_i));
local_mp_i.page_control = mpi->page_control;
local_mp_i.peri_type = mpi->peri_type;
local_mp_i.inq_byte6 = mpi->inq_byte6;
local_mp_i.resp_len = mpi->resp_len;
do {
local_mp_i.page = (pagestart[0] & 0x3f);
local_mp_i.subpage = (pagestart[0] & 0x40) ? pagestart[1] : 0;
if(0 == local_mp_i.page) { /* page==0 vendor (unknown) format */
off = 0;
len = mpi->resp_len - offset; /* should be last listed page */
} else if (local_mp_i.subpage) {
off = 4;
len = (pagestart[2] << 8) + pagestart[3] + 4;
} else {
off = 2;
len = pagestart[1] + 2;
}
prefix[0] = '\0';
done = 0;
if ((! decode_in_hex) && ((mpf = get_mpage_name_func(&local_mp_i))) &&
mpf->func) {
if (multiple && x_interface && !replace) {
if (local_mp_i.subpage)
snprintf(prefix, sizeof(prefix), "sginfo -t 0x%x,0x%x"
" -XR %s ", local_mp_i.page, local_mp_i.subpage,
device_name);
else
snprintf(prefix, sizeof(prefix), "sginfo -t 0x%x -XR %s ",
local_mp_i.page, device_name);
}
res = mpf->func(&local_mp_i, prefix);
if (DECODE_FAILED_TRY_HEX != res) {
done = 1;
status |= res;
}
}
if (! done) {
if (x_interface && replace)
return put_mode_page(&local_mp_i, cbuffer2);
else {
if (multiple && x_interface && !replace) {
if (local_mp_i.subpage)
snprintf(prefix, sizeof(prefix), "sginfo -u 0x%x,0x%x"
" -XR %s ", local_mp_i.page,
local_mp_i.subpage, device_name);
else
snprintf(prefix, sizeof(prefix), "sginfo -u 0x%x -XR "
"%s ", local_mp_i.page, device_name);
}
print_hex_page(&local_mp_i, prefix, pagestart, off, len);
}
}
offset += len;
pagestart = cbuffer2 + offset;
} while (multiple && (offset < mpi->resp_len));
return status;
}
static void
inqfieldname(uint8_t *deststr, const uint8_t *srcbuf, int maxlen)
{
int i;
memset(deststr, '\0', MAX_INQFIELD_LEN);
for (i = maxlen - 1; i >= 0 && isspace(srcbuf[i]); --i)
;
memcpy(deststr, srcbuf, i + 1);
}
static int
do_inquiry(int * peri_type, int * resp_byte6, int inquiry_verbosity)
{
int status;
uint8_t cmd[6];
uint8_t fieldname[MAX_INQFIELD_LEN];
uint8_t *pagestart;
struct scsi_cmnd_io sci;
memset(cbuffer, 0, INQUIRY_RESP_INITIAL_LEN);
cbuffer[0] = 0x7f;
cmd[0] = 0x12; /* INQUIRY */
cmd[1] = 0x00; /* evpd=0 */
cmd[2] = 0x00; /* page code = 0 */
cmd[3] = 0x00; /* (reserved) */
cmd[4] = INQUIRY_RESP_INITIAL_LEN; /* allocation length */
cmd[5] = 0x00; /* control */
sci.cmnd = cmd;
sci.cmnd_len = sizeof(cmd);
sci.dxfer_dir = DXFER_FROM_DEVICE;
sci.dxfer_len = INQUIRY_RESP_INITIAL_LEN;
sci.dxferp = cbuffer;
status = do_scsi_io(&sci);
if (status) {
printf("Error doing INQUIRY (1)\n");
return status;
}
if (trace_cmd > 1) {
printf(" inquiry response:\n");
dump(cbuffer, INQUIRY_RESP_INITIAL_LEN);
}
pagestart = cbuffer;
if (peri_type)
*peri_type = pagestart[0] & 0x1f;
if (resp_byte6)
*resp_byte6 = pagestart[6];
if (0 == inquiry_verbosity)
return 0;
if ((pagestart[4] + 5) < INQUIRY_RESP_INITIAL_LEN) {
printf("INQUIRY response too short: expected 36 bytes, got %d\n",
pagestart[4] + 5);
return -EINVAL;
}
if (!x_interface && !replace) {
printf("INQUIRY response (cmd: 0x12)\n");
printf("----------------------------\n");
};
bitfield(pagestart + 0, "Device Type", 0x1f, 0);
if (2 == inquiry_verbosity) {
bitfield(pagestart + 0, "Peripheral Qualifier", 0x7, 5);
bitfield(pagestart + 1, "Removable", 1, 7);
bitfield(pagestart + 2, "Version", 0xff, 0);
bitfield(pagestart + 3, "NormACA", 1, 5);
bitfield(pagestart + 3, "HiSup", 1, 4);
bitfield(pagestart + 3, "Response Data Format", 0xf, 0);
bitfield(pagestart + 5, "SCCS", 1, 7);
bitfield(pagestart + 5, "ACC", 1, 6);
bitfield(pagestart + 5, "ALUA", 3, 4);
bitfield(pagestart + 5, "3PC", 1, 3);
bitfield(pagestart + 5, "Protect", 1, 0);
bitfield(pagestart + 6, "BQue", 1, 7);
bitfield(pagestart + 6, "EncServ", 1, 6);
bitfield(pagestart + 6, "MultiP", 1, 4);
bitfield(pagestart + 6, "MChngr", 1, 3);
bitfield(pagestart + 6, "Addr16", 1, 0);
bitfield(pagestart + 7, "Relative Address", 1, 7);
bitfield(pagestart + 7, "Wide bus 16", 1, 5);
bitfield(pagestart + 7, "Synchronous neg.", 1, 4);
bitfield(pagestart + 7, "Linked Commands", 1, 3);
bitfield(pagestart + 7, "Command Queueing", 1, 1);
}
if (x_interface)
printf("\n");
inqfieldname(fieldname, pagestart + 8, 8);
printf("%s%s\n", (!x_interface ? "Vendor: " : ""),
fieldname);
inqfieldname(fieldname, pagestart + 16, 16);
printf("%s%s\n", (!x_interface ? "Product: " : ""),
fieldname);
inqfieldname(fieldname, pagestart + 32, 4);
printf("%s%s\n", (!x_interface ? "Revision level: " : ""),
fieldname);
printf("\n");
return status;
}
static int
do_serial_number(void)
{
int status, pagelen;
uint8_t cmd[6];
uint8_t *pagestart;
struct scsi_cmnd_io sci;
const uint8_t serial_vpd = 0x80;
const uint8_t supported_vpd = 0x0;
/* check supported VPD pages + unit serial number well formed */
cmd[0] = 0x12; /* INQUIRY */
cmd[1] = 0x01; /* evpd=1 */
cmd[2] = supported_vpd;
cmd[3] = 0x00; /* (reserved) */
cmd[4] = 0x04; /* allocation length */
cmd[5] = 0x00; /* control */
sci.cmnd = cmd;
sci.cmnd_len = sizeof(cmd);
sci.dxfer_dir = DXFER_FROM_DEVICE;
sci.dxfer_len = 4;
sci.dxferp = cbuffer;
status = do_scsi_io(&sci);
if (status) {
printf("No serial number (error doing INQUIRY, supported VPDs)\n\n");
return status;
}
if (! ((supported_vpd == cbuffer[1]) && (0 == cbuffer[2]))) {
printf("No serial number (bad format for supported VPDs)\n\n");
return -1;
}
cmd[0] = 0x12; /* INQUIRY */
cmd[1] = 0x01; /* evpd=1 */
cmd[2] = serial_vpd;
cmd[3] = 0x00; /* (reserved) */
cmd[4] = 0x04; /* allocation length */
cmd[5] = 0x00; /* control */
sci.cmnd = cmd;
sci.cmnd_len = sizeof(cmd);
sci.dxfer_dir = DXFER_FROM_DEVICE;
sci.dxfer_len = 4;
sci.dxferp = cbuffer;
status = do_scsi_io(&sci);
if (status) {
printf("No serial number (error doing INQUIRY, serial number)\n\n");
return status;
}
if (! ((serial_vpd == cbuffer[1]) && (0 == cbuffer[2]))) {
printf("No serial number (bad format for serial number)\n\n");
return -1;
}
pagestart = cbuffer;
pagelen = 4 + pagestart[3];
cmd[0] = 0x12; /* INQUIRY */
cmd[1] = 0x01; /* evpd=1 */
cmd[2] = serial_vpd;
cmd[3] = 0x00; /* (reserved) */
cmd[4] = (uint8_t)pagelen; /* allocation length */
cmd[5] = 0x00; /* control */
sci.cmnd = cmd;
sci.cmnd_len = sizeof(cmd);
sci.dxfer_dir = DXFER_FROM_DEVICE;
sci.dxfer_len = pagelen;
sci.dxferp = cbuffer;
status = do_scsi_io(&sci);
if (status) {
printf("No serial number (error doing INQUIRY, serial number)\n\n");
return status;
}
if (trace_cmd > 1) {
printf(" inquiry (vpd page 0x80) response:\n");
dump(cbuffer, pagelen);
}
pagestart[pagestart[3] + 4] = '\0';
printf("Serial Number '%s'\n\n", pagestart + 4);
return status;
}
typedef struct sg_map {
int bus;
int channel;
int target_id;
int lun;
char * dev_name;
} Sg_map;
typedef struct my_scsi_idlun
{
int mux4;
int host_unique_id;
} My_scsi_idlun;
#define MDEV_NAME_SZ 256
static void
make_dev_name(char * fname, int k, int do_numeric)
{
char buff[MDEV_NAME_SZ];
size_t len;
strncpy(fname, "/dev/sg", MDEV_NAME_SZ);
fname[MDEV_NAME_SZ - 1] = '\0';
len = strlen(fname);
if (do_numeric)
snprintf(fname + len, MDEV_NAME_SZ - len, "%d", k);
else {
if (k <= 26) {
buff[0] = 'a' + (char)k;
buff[1] = '\0';
strcat(fname, buff);
}
else
strcat(fname, "xxxx");
}
}
static Sg_map sg_map_arr[MAX_SG_DEVS + 1];
#define MAX_HOLES 4
/* Print out a list of the known devices on the system */
static void
show_devices(int raw)
{
int k, j, fd, err, bus, n;
My_scsi_idlun m_idlun;
char name[MDEV_NAME_SZ];
char dev_name[MDEV_NAME_SZ + 6];
char ebuff[EBUFF_SZ];
int do_numeric = 1;
int max_holes = MAX_HOLES;
DIR *dir_ptr;
struct dirent *entry;
char *tmpptr;
dir_ptr=opendir("/dev");
if ( dir_ptr == NULL ) {
perror("/dev");
exit(1);
}
j=0;
while ( (entry=readdir(dir_ptr)) != NULL ) {
switch(entry->d_type) {
case DT_LNK:
case DT_CHR:
case DT_BLK:
break;
default:
continue;
}
switch(entry->d_name[0]) {
case 's':
case 'n':
break;
default:
continue;
}
if ( strncmp("sg",entry->d_name,2) == 0 ) {
continue;
}
if ( strncmp("sd",entry->d_name,2) == 0 ) {
continue;
}
if ( isdigit(entry->d_name[strlen(entry->d_name)-1]) ) {
continue;
}
if ( strncmp("snapshot",entry->d_name,8) == 0 ) {
continue;
}
snprintf(dev_name, sizeof(dev_name),"/dev/%s",entry->d_name);
fd = open(dev_name, O_RDONLY | O_NONBLOCK);
if (fd < 0)
continue;
err = ioctl(fd, SCSI_IOCTL_GET_BUS_NUMBER, &(sg_map_arr[j].bus));
if (err < 0) {
#if 0
snprintf(ebuff, EBUFF_SZ,
"SCSI(1) ioctl on %s failed", dev_name);
perror(ebuff);
#endif
close(fd);
continue;
}
err = ioctl(fd, SCSI_IOCTL_GET_IDLUN, &m_idlun);
if (err < 0) {
snprintf(ebuff, EBUFF_SZ,
"SCSI(2) ioctl on %s failed", dev_name);
perror(ebuff);
close(fd);
continue;
}
sg_map_arr[j].channel = (m_idlun.mux4 >> 16) & 0xff;
sg_map_arr[j].lun = (m_idlun.mux4 >> 8) & 0xff;
sg_map_arr[j].target_id = m_idlun.mux4 & 0xff;
n = strlen(dev_name);
/* memory leak ... no free()s for this malloc() */
tmpptr = (char *)malloc(n + 1);
snprintf(tmpptr, n + 1, "%.*s", n, dev_name);
/* strncpy(tmpptr,dev_name,strlen(dev_name)+1); */
sg_map_arr[j].dev_name = tmpptr;
#if 0
printf("[scsi%d ch=%d id=%d lun=%d %s] ", sg_map_arr[j].bus,
sg_map_arr[j].channel, sg_map_arr[j].target_id, sg_map_arr[j].lun,
sg_map_arr[j].dev_name);
#endif
printf("%s ", dev_name);
close(fd);
if (++j >= MAX_SG_DEVS)
break;
}
closedir(dir_ptr);
printf("\n"); /* <<<<<<<<<<<<<<<<<<<<< */
for (k = 0; k < MAX_SG_DEVS; k++) {
if ( raw ) {
sprintf(name,"/dev/raw/raw%d",k);
fd = open(name, O_RDWR | O_NONBLOCK);
if (fd < 0) {
continue;
}
}
else {
make_dev_name(name, k, do_numeric);
fd = open(name, O_RDWR | O_NONBLOCK);
if (fd < 0) {
if ((ENOENT == errno) && (0 == k)) {
do_numeric = 0;
make_dev_name(name, k, do_numeric);
fd = open(name, O_RDWR | O_NONBLOCK);
}
if (fd < 0) {
if (EBUSY == errno)
continue; /* step over if O_EXCL already on it */
else {
#if 0
snprintf(ebuff, EBUFF_SZ,
"open on %s failed (%d)", name, errno);
perror(ebuff);
#endif
if (max_holes-- > 0)
continue;
else
break;
}
}
}
}
max_holes = MAX_HOLES;
err = ioctl(fd, SCSI_IOCTL_GET_BUS_NUMBER, &bus);
if (err < 0) {
if ( ! raw ) {
snprintf(ebuff, EBUFF_SZ, "SCSI(3) ioctl on %s failed", name);
perror(ebuff);
}
close(fd);
continue;
}
err = ioctl(fd, SCSI_IOCTL_GET_IDLUN, &m_idlun);
if (err < 0) {
if ( ! raw ) {
snprintf(ebuff, EBUFF_SZ, "SCSI(3) ioctl on %s failed", name);
perror(ebuff);
}
close(fd);
continue;
}
#if 0
printf("[scsi%d ch=%d id=%d lun=%d %s]", bus,
(m_idlun.mux4 >> 16) & 0xff, m_idlun.mux4 & 0xff,
(m_idlun.mux4 >> 8) & 0xff, name);
#endif
for (j = 0; sg_map_arr[j].dev_name; ++j) {
if ((bus == sg_map_arr[j].bus) &&
((m_idlun.mux4 & 0xff) == sg_map_arr[j].target_id) &&
(((m_idlun.mux4 >> 16) & 0xff) == sg_map_arr[j].channel) &&
(((m_idlun.mux4 >> 8) & 0xff) == sg_map_arr[j].lun)) {
printf("%s [=%s scsi%d ch=%d id=%d lun=%d]\n", name,
sg_map_arr[j].dev_name, bus,
((m_idlun.mux4 >> 16) & 0xff), m_idlun.mux4 & 0xff,
((m_idlun.mux4 >> 8) & 0xff));
break;
}
}
if (NULL == sg_map_arr[j].dev_name)
printf("%s [scsi%d ch=%d id=%d lun=%d]\n", name, bus,
((m_idlun.mux4 >> 16) & 0xff), m_idlun.mux4 & 0xff,
((m_idlun.mux4 >> 8) & 0xff));
close(fd);
}
printf("\n");
}
#define DEVNAME_SZ 256
static int
open_sg_io_dev(char * devname)
{
int fd, fdrw, err, bus, bbus, k, v;
My_scsi_idlun m_idlun, mm_idlun;
int do_numeric = 1;
char name[DEVNAME_SZ];
struct stat a_st;
int block_dev = 0;
strncpy(name, devname, DEVNAME_SZ);
name[DEVNAME_SZ - 1] = '\0';
fd = open(name, O_RDONLY | O_NONBLOCK);
if (fd < 0)
return fd;
if ((ioctl(fd, SG_GET_VERSION_NUM, &v) >= 0) && (v >= 30000)) {
fdrw = open(name, O_RDWR | O_NONBLOCK);
if (fdrw >= 0) {
close(fd);
return fdrw;
}
return fd;
}
if (fstat(fd, &a_st) < 0) {
fprintf(stderr, "could do fstat() on fd ??\n");
close(fd);
return -9999;
}
if (S_ISBLK(a_st.st_mode))
block_dev = 1;
if (block_dev || (ioctl(fd, SG_GET_TIMEOUT, 0) < 0)) {
err = ioctl(fd, SCSI_IOCTL_GET_BUS_NUMBER, &bus);
if (err < 0) {
fprintf(stderr, "A device name that understands SCSI commands "
"is required\n");
close(fd);
return -9999;
}
err = ioctl(fd, SCSI_IOCTL_GET_IDLUN, &m_idlun);
if (err < 0) {
fprintf(stderr, "A SCSI device name is required(2)\n");
close(fd);
return -9999;
}
close(fd);
for (k = 0; k < MAX_SG_DEVS; k++) {
make_dev_name(name, k, do_numeric);
fd = open(name, O_RDWR | O_NONBLOCK);
if (fd < 0) {
if ((ENOENT == errno) && (0 == k)) {
do_numeric = 0;
make_dev_name(name, k, do_numeric);
fd = open(name, O_RDWR | O_NONBLOCK);
}
if (fd < 0) {
if (EBUSY == errno)
continue; /* step over if O_EXCL already on it */
else
break;
}
}
err = ioctl(fd, SCSI_IOCTL_GET_BUS_NUMBER, &bbus);
if (err < 0) {
perror("sg ioctl failed");
close(fd);
fd = -9999;
}
err = ioctl(fd, SCSI_IOCTL_GET_IDLUN, &mm_idlun);
if (err < 0) {
perror("sg ioctl failed");
close(fd);
fd = -9999;
}
if ((bus == bbus) &&
((m_idlun.mux4 & 0xff) == (mm_idlun.mux4 & 0xff)) &&
(((m_idlun.mux4 >> 8) & 0xff) ==
((mm_idlun.mux4 >> 8) & 0xff)) &&
(((m_idlun.mux4 >> 16) & 0xff) ==
((mm_idlun.mux4 >> 16) & 0xff)))
break;
else {
close(fd);
fd = -9999;
}
}
}
if (fd >= 0) {
if ((ioctl(fd, SG_GET_VERSION_NUM, &v) < 0) || (v < 30000)) {
fprintf(stderr, "requires lk 2.4 (sg driver), lk 2.6 or lk 3 "
"series\n");
close(fd);
return -9999;
}
close(fd);
return open(name, O_RDWR | O_NONBLOCK);
}
else
return fd;
}
static void
usage(const char *errtext)
{
if (errtext)
fprintf(stderr, "Error: sginfo: %s\n", errtext);
fprintf(stderr, "Usage: sginfo [-options] [device] "
"[replacement_values]\n");
fputs("\tAllowed options are:\n"
"\t-6 Do 6 byte mode sense and select commands (def: 10 "
"bytes).\n"
"\t-a Display inquiry info, serial # and all mode pages.\n"
"\t-A Similar to '-a' but displays all subpages as well.\n"
"\t-c Access Caching Page.\n"
"\t-C Access Control Mode Page.\n"
"\t-d Display defect lists (default format: index).\n"
"\t-D Access Disconnect-Reconnect Page.\n"
"\t-e Access Read-Write Error Recovery page.\n"
"\t-E Access Control Extension page.\n"
"\t-f Access Format Device Page.\n"
"\t-Farg Format of the defect list:\n"
"\t\t-Flogical - logical block addresses (32 bit)\n"
"\t\t-Flba64 - logical block addresses (64 bit)\n"
"\t\t-Fphysical - physical blocks\n"
"\t\t-Findex - defect bytes from index\n"
"\t\t-Fhead - sort by head\n", stdout);
fputs("\t-g Access Rigid Disk Drive Geometry Page.\n"
"\t-G Display 'grown' defect list (default format: index).\n"
"\t-i Display information from INQUIRY command.\n"
"\t-I Access Informational Exception page.\n"
"\t-l List known scsi devices on the system [DEPRECATED]\n"
"\t-n Access Notch and Partition Page.\n"
"\t-N Negate (stop) storing to saved page (active with -R).\n"
"\t-P Access Power Condition Page.\n"
"\t-r List known raw scsi devices on the system\n"
"\t-s Display serial number (from INQUIRY VPD page).\n"
"\t-t<pn[,sp]> Access mode page <pn> [subpage <sp>] and decode.\n"
"\t-T Trace commands (for debugging, double for more)\n"
"\t-u<pn[,sp]> Access mode page <pn> [subpage <sp>], output in hex\n"
"\t-v Show version number\n"
"\t-V Access Verify Error Recovery Page.\n"
"\t-z single fetch mode pages (rather than double fetch)\n"
"\n", stdout);
fputs("\tOnly one of the following three options can be specified.\n"
"\tNone of these three implies the current values are returned.\n", stdout);
fputs("\t-m Access modifiable fields instead of current values\n"
"\t-M Access manufacturer defaults instead of current values\n"
"\t-S Access saved defaults instead of current values\n\n"
"\t-X Use list (space separated values) rather than table.\n"
"\t-R Replace parameters - best used with -X (expert use only)\n"
"\t [replacement parameters placed after device on command line]\n\n",
stdout);
printf("\t sginfo version: %s; See man page for more details.\n",
version_str);
exit(2);
}
int main(int argc, char *argv[])
{
int k, j, n;
unsigned int unum, unum2;
int decode_in_hex = 0;
char c;
char * cp;
int status = 0;
long tmp;
struct mpage_info mp_i;
int inquiry_verbosity = 0;
int show_devs = 0, show_raw = 0;
int found = 0;
if (argc < 2)
usage(NULL);
memset(&mp_i, 0, sizeof(mp_i));
while ((k = getopt(argc, argv, "6aAcCdDeEfgGiIlmMnNPrRsSTvVXzF:t:u:")) !=
EOF) {
c = (char)k;
switch (c) {
case '6':
mode6byte = 1;
break;
case 'a':
inquiry_verbosity = 1;
serial_number = 1;
mp_i.page = MP_LIST_PAGES;
break;
case 'A':
inquiry_verbosity = 1;
serial_number = 1;
mp_i.page = MP_LIST_PAGES;
mp_i.subpage = MP_LIST_SUBPAGES;
break;
case 'c':
mp_i.page = 0x8;
break;
case 'C':
mp_i.page = 0xa;
break;
case 'd':
defect = 1;
break;
case 'D':
mp_i.page = 0x2;
break;
case 'e':
mp_i.page = 0x1;
break;
case 'E':
mp_i.page = 0xa;
mp_i.subpage = 0x1;
break;
case 'f':
mp_i.page = 0x3;
break;
case 'F':
if (!strcasecmp(optarg, "logical"))
defectformat = 0x0;
else if (!strcasecmp(optarg, "lba64"))
defectformat = 0x3;
else if (!strcasecmp(optarg, "physical"))
defectformat = 0x5;
else if (!strcasecmp(optarg, "index"))
defectformat = 0x4;
else if (!strcasecmp(optarg, "head"))
defectformat = HEAD_SORT_TOKEN;
else
usage("Illegal -F parameter, must be one of logical, "
"physical, index or head");
break;
case 'g':
mp_i.page = 0x4;
break;
case 'G':
grown_defect = 1;
break;
case 'i': /* just vendor, product and revision for '-i -i' */
inquiry_verbosity = (2 == inquiry_verbosity) ? 1 : 2;
break;
case 'I':
mp_i.page = 0x1c;
break;
case 'l':
show_devs = 1;
break;
case 'm': /* modifiable page control */
if (0 == mp_i.page_control)
mp_i.page_control = 1;
else
usage("can only have one of 'm', 'M' and 'S'");
break;
case 'M': /* manufacturer's==default page control */
if (0 == mp_i.page_control)
mp_i.page_control = 2;
else
usage("can only have one of 'M', 'm' and 'S'");
break;
case 'n':
mp_i.page = 0xc;
break;
case 'N':
negate_sp_bit = 1;
break;
case 'P':
mp_i.page = 0x1a;
break;
case 'r':
show_raw = 1;
break;
case 'R':
replace = 1;
break;
case 's':
serial_number = 1;
break;
case 'S': /* saved page control */
if (0 == mp_i.page_control)
mp_i.page_control = 3;
else
usage("can only have one of 'S', 'm' and 'M'");
break;
case 'T':
trace_cmd++;
break;
case 't':
case 'u':
if ('u' == c)
decode_in_hex = 1;
while (' ' == *optarg)
optarg++;
if ('0' == *optarg) {
unum = 0;
unum2 = 0;
j = sscanf(optarg, "0x%x,0x%x", &unum, &unum2);
mp_i.page = unum;
if (1 == j) {
cp = strchr(optarg, ',');
if (cp && (1 == sscanf(cp, ",%d", &mp_i.subpage)))
j = 2;
} else
mp_i.subpage = unum2;
} else
j = sscanf(optarg, "%d,%d", &mp_i.page, &mp_i.subpage);
if (1 == j)
mp_i.subpage = 0;
else if (j < 1)
usage("argument following '-u' should be of form "
"<pg>[,<subpg>]");
if ((mp_i.page < 0) || (mp_i.page > MP_LIST_PAGES) ||
(mp_i.subpage < 0) || (mp_i.subpage > MP_LIST_SUBPAGES))
usage("mode pages range from 0 .. 63, subpages from "
"1 .. 255");
found = 1;
break;
case 'v':
fprintf(stdout, "sginfo version: %s\n", version_str);
return 0;
case 'V':
mp_i.page = 0x7;
break;
case 'X':
x_interface = 1;
break;
case 'z':
single_fetch = 1;
break;
case '?':
usage("Unknown option");
break;
default:
fprintf(stdout, "Unknown option '-%c' (ascii 0x%02x)\n", c, c);
usage("bad option");
}
}
if (replace && !x_interface)
usage("-R requires -X");
if (replace && mp_i.page_control)
usage("-R not allowed for -m, -M or -S");
if (x_interface && replace && ((MP_LIST_PAGES == mp_i.page) ||
(MP_LIST_SUBPAGES == mp_i.subpage)))
usage("-XR can be used only with exactly one page.");
if (replace && (3 != mp_i.page_control)) {
memset (is_hex, 0, 32);
for (j = 1; j < argc - optind; j++) {
if (strncmp(argv[optind + j], "0x", 2) == 0) {
char *pnt = argv[optind + j] + 2;
replacement_values[j] = 0;
/* This is a kluge, but we can handle 64 bit quantities this way. */
while (*pnt) {
if (*pnt >= 'a' && *pnt <= 'f')
*pnt -= 32;
replacement_values[j] = (replacement_values[j] << 4) |
(*pnt > '9' ? (*pnt - 'A' + 10) : (*pnt - '0'));
pnt++;
}
continue;
}
if (argv[optind + j][0] == '@') {
/*Ensure that this string contains an even number of hex-digits */
int len = strlen(argv[optind + j] + 1);
if ((len & 1) || (len != (int)strspn(argv[optind + j] + 1,
"0123456789ABCDEFabcdef")))
usage("Odd number of chars or non-hex digit in "
"@hexdatafield");
replacement_values[j] = (unsigned long) argv[optind + j];
is_hex[j] = 1;
continue;
}
/* Using a tmp here is silly but the most clean approach */
n = sscanf(argv[optind + j], "%ld", &tmp);
replacement_values[j] = ((1 == n) ? tmp : 0);
}
n_replacement_values = argc - optind - 1;
}
if (show_devs) {
show_devices(0);
exit(0);
}
if (show_raw) {
show_devices(1);
exit(0);
}
if (optind >= argc)
usage("no device name given");
glob_fd = open_sg_io_dev(device_name = argv[optind]);
if (glob_fd < 0) {
if (-9999 == glob_fd)
fprintf(stderr, "Couldn't find sg device corresponding to %s\n",
device_name);
else {
perror("sginfo(open)");
fprintf(stderr, "file=%s, or no corresponding sg device found\n",
device_name);
fprintf(stderr, "Is sg driver loaded?\n");
}
exit(1);
}
#if 0
if (!x_interface)
printf("\n");
#endif
if (! (found || mp_i.page || mp_i.subpage || inquiry_verbosity ||
serial_number)) {
if (trace_cmd > 0)
fprintf(stdout, "nothing selected so do a short INQUIRY\n");
inquiry_verbosity = 1;
}
status |= do_inquiry(&mp_i.peri_type, &mp_i.inq_byte6,
inquiry_verbosity);
if (serial_number)
do_serial_number(); /* ignore error */
if (mp_i.page > 0)
status |= do_user_page(&mp_i, decode_in_hex);
if (defect)
status |= read_defect_list(0);
if (grown_defect)
status |= read_defect_list(1);
return status ? 1 : 0;
}