DSMON-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE, Integer32,
Counter32, Gauge32
FROM SNMPv2-SMI
MODULE-COMPLIANCE, OBJECT-GROUP
FROM SNMPv2-CONF
RowStatus, TimeStamp, TEXTUAL-CONVENTION, TruthValue
FROM SNMPv2-TC
OwnerString, rmon
FROM RMON-MIB
protocolDirLocalIndex, LastCreateTime,
DataSource, ZeroBasedCounter32, TimeFilter
FROM RMON2-MIB
CounterBasedGauge64, ZeroBasedCounter64
FROM HCNUM-TC
SnmpAdminString
FROM SNMP-FRAMEWORK-MIB
Dscp
FROM DIFFSERV-DSCP-TC;
dsmonMIB MODULE-IDENTITY
LAST-UPDATED "200205310000Z"
ORGANIZATION "IETF RMONMIB Working Group"
CONTACT-INFO
" Andy Bierman
Cisco Systems, Inc.
RMONMIB WG Chair and DSMON MIB Editor
Postal: 170 West Tasman Drive
San Jose, CA USA 95134
Tel: +1 408 527-3711
E-mail: abierman@cisco.com
Send comments to <rmonmib@ietf.org>
Mailing list subscription info:
http://www.ietf.org/mailman/listinfo/rmonmib "
DESCRIPTION
"This module defines Remote Monitoring MIB extensions for
Differentiated Services enabled networks.
RMON DIFFSERV DSCP statistics
* Per Counter Aggregation Group
* Per Protocol Per Counter Aggregation Group
* Per Counter Aggregation Group Per Host
* Per Counter Aggregation Group Per Host-Pair
In order to maintain the RMON 'look-and-feel' and semantic
consistency, some of the text from the RMON-2 and HC-RMON
MIBs by Steve Waldbusser has been adapted for use in this
MIB."
REVISION "200205310000Z"
DESCRIPTION
"Initial version of the DSMON MIB module. This version
published as RFC 3287."
::= { rmon 26 }
dsmonObjects OBJECT IDENTIFIER ::= { dsmonMIB 1 }
dsmonNotifications OBJECT IDENTIFIER ::= { dsmonMIB 2 }
dsmonConformance OBJECT IDENTIFIER ::= { dsmonMIB 3 }
dsmonAggObjects OBJECT IDENTIFIER ::= { dsmonObjects 1 }
dsmonStatsObjects OBJECT IDENTIFIER ::= { dsmonObjects 2 }
dsmonPdistObjects OBJECT IDENTIFIER ::= { dsmonObjects 3 }
dsmonHostObjects OBJECT IDENTIFIER ::= { dsmonObjects 4 }
dsmonCapsObjects OBJECT IDENTIFIER ::= { dsmonObjects 5 }
dsmonMatrixObjects OBJECT IDENTIFIER ::= { dsmonObjects 6 }
--
-- Textual Convention to define a
-- DSMON Counter Aggregation Group Index
--
DsmonCounterAggGroupIndex ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This TC describes a data type which identifies a DSMON
counter aggregation group, which is an arbitrary grouping of
conceptual counters, for monitoring purposes only. The
range for this data type begins with zero (instead of
one), to allow for a direct mapping between counter
indexing schemes that start at zero (e.g. DSCP values in
packets) and counter aggregation group values."
SYNTAX Integer32 (0..2147483647)
--
-- Textual Convention to define a
-- DSMON Counter Aggregation Profile Index
--
DsmonCounterAggProfileIndex ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This TC describes a data type which identifies a DSMON
counter aggregation profile, which is a set of counter
aggregation group assignments for each of the 64 DSCP
values, for a particular statistical collection."
SYNTAX Integer32 (1..2147483647)
-- ***********************************************************
-- * *
-- * D S M O N C A P A B I L I T I E S *
-- * *
-- ***********************************************************
dsmonCapabilities OBJECT-TYPE
SYNTAX BITS {
dsmonCounterAggControl(0),
dsmonStats(1),
dsmonStatsOvfl(2),
dsmonStatsHC(3),
dsmonPdist(4),
dsmonPdistOvfl(5),
dsmonPdistHC(6),
dsmonHost(7),
dsmonHostOvfl(8),
dsmonHostHC(9),
dsmonCaps(10),
dsmonMatrix(11),
dsmonMatrixOvfl(12),
dsmonMatrixHC(13)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object provides an indication of the DSMON groups
supported by the agent. If a bit is set, then the agent
implements all of the objects in the DSMON object group,
where bit 'n' represents the MIB group identified by the
OBJECT IDENTIFIER value { dsmonGroups n+1 }."
::= { dsmonCapsObjects 1 }
-- ***********************************************************
-- * *
-- * A G G R E G A T I O N C O N T R O L G R O U P S *
-- * *
-- ***********************************************************
dsmonMaxAggGroups OBJECT-TYPE
SYNTAX Integer32 (2..64)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum number of counter aggregation groups that this
agent can support. The agent will allow this number of
distinct groups to be configured in the
dsmonAggProfileTable, numbered from '0' to
'dsmonMaxAggGroups - 1', for each counter aggregation
profile entry supported by the agent.
The agent MUST NOT lower this value during system operation,
and SHOULD set this object to an appropriate value during
system initialization."
::= { dsmonAggObjects 1 }
dsmonAggControlLocked OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Controls the setup of counter aggregation groups for this
agent.
If this object contains the value 'true', then write access
to the objects in the dsmonAggControlTable (except the
dsmonAggControlOwner object), dsmonAggProfileTable, and
dsmonAggGroupTable is not permitted, and data collection is
possible. This object only controls write access to these
MIB objects. The DSMON data collection control tables
(e.g., dsmonHostCtlTable) can be configured at any time,
regardless of the value of this object.
If this object contains the value 'false', write access to
the objects in the dsmonAggControlTable,
dsmonAggProfileTable, and dsmonAggGroupTable is permitted,
and data collection is not possible. In addition, all
objects in all DSMON data tables (e.g., dsmonStatsTable)
shall be deleted.
An agent is not required to process SNMP Set Requests for
this object in conjunction with other objects from this MIB.
This is intended to simplify the processing of Set Requests
for tables such as the dsmonAggProfileTable, by eliminating
the possibility that a single Set PDU will contain multiple
varbinds which are in conflict, such as a PDU which both
modifies the dsmonAggProfileTable and locks the
dsmonAggProfileTable at the same time.
Note that the agent is not required to validate the entire
counter aggregation configuration when an attempt is made to
transition an instance of this object from 'true' to
'false'. That validation is done if and when a DSMON data
collection is activated.
An agent is required to reactivate any suspended data
collections when this object transitions to 'true', Each
active data control entry (e.g., dsmonStatsControlEntry),
will be validated with respect to the new counter
aggregation configuration. If the counter aggregation
profile referenced in the data collection is valid, then
that collection will be restarted. Otherwise, the RowStatus
object (e.g., dsmonStatsControlStatus) will be set to
'notReady' for that collection control entry."
::= { dsmonAggObjects 2 }
dsmonAggControlChanges OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of times the value of the
dsmonAggControlLocked object has changed. A management
station can use this object to detect if counters in the
DSMON data tables (e.g., dsmonStatsEntry) have been deleted
and recreated between polls.
This object shall be incremented by one each time the
dsmonAggControlLocked object changes from 'false' to 'true',
or from 'true' to 'false'."
::= { dsmonAggObjects 3 }
dsmonAggControlLastChangeTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object identifies the value of sysUpTime at the moment
the dsmonAggControlLocked object was last modified. A
management station can use this object to detect if counters
in the DSMON data tables (e.g., dsmonStatsEntry) have been
deleted and recreated between polls.
This object shall be updated with the current value of
sysUpTime, if the dsmonAggControlLocked object changes from
'false' to 'true', or from 'true' to 'false'.
Upon system initialization, this object shall contain the
value zero."
::= { dsmonAggObjects 4 }
--
-- Counter Aggregation Control Table
--
dsmonAggControlTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonAggControlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides an overall description and control
point for all dsmonAggProfileEntries with the same
dsmonAggControlIndex value.
A management application SHOULD create a counter aggregation
profile by first creating and activating an entry in this
table. This will cause the agent to create a set of 64
dsmonAggProfileEntries on behalf of this control entry. An
application can then set the individual counter aggregation
group assignments for each of the 64 DSCP values,
This table MUST NOT be modified if the dsmonAggControlLocked
object is equal to 'true'.
Note that an agent MAY choose to limit the actual number of
entries which may be created in this table, and
(independently) the number of counter aggregation profiles
which may be applied to a particular data source. In this
case, the agent SHOULD return an error-status of
'resourceUnavailable(13)', as per section 4.2.5 of the
'Protocol Operations for SNMPv2' specification [RFC1905].
The agent SHOULD support non-volatile configuration of this
table, and upon system initialization, the table SHOULD be
initialized with the saved values. Otherwise, each
potential counter aggregation group description string
SHOULD contain the empty string."
::= { dsmonAggObjects 5 }
dsmonAggControlEntry OBJECT-TYPE
SYNTAX DsmonAggControlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in the dsmonAggControlTable."
INDEX { dsmonAggControlIndex }
::= { dsmonAggControlTable 1 }
DsmonAggControlEntry ::= SEQUENCE {
dsmonAggControlIndex DsmonCounterAggProfileIndex,
dsmonAggControlDescr SnmpAdminString,
dsmonAggControlOwner OwnerString,
dsmonAggControlStatus RowStatus
}
dsmonAggControlIndex OBJECT-TYPE
SYNTAX DsmonCounterAggProfileIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An arbitrary integer index value used to identify the
counter aggregation profile specified by this control
entry."
::= { dsmonAggControlEntry 1 }
dsmonAggControlDescr OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (0..64))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An administratively assigned description of the counter
aggregation profile identified by this entry.
Upon first creation of an instance of this object, the agent
SHOULD set this object to the empty string. If the agent
supports non-volatile storage, then this object SHOULD be
re-initialized with its stored value after a system reboot.
This object MUST NOT be modified if the associated
dsmonAggControlStatus object is equal to 'active', or the
dsmonAggControlLocked object is equal to 'true'."
::= { dsmonAggControlEntry 2 }
dsmonAggControlOwner OBJECT-TYPE
SYNTAX OwnerString
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The entity that configured this entry and is therefore
using the resources assigned to it."
::= { dsmonAggControlEntry 3 }
dsmonAggControlStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this row.
An entry MUST NOT exist in the active state unless all
objects in the entry have an appropriate value.
Upon setting this object to active(1), the agent will create
a complete set of 64 associated entries in the
dsmonAggProfileTable.
If this object is not equal to active(1), all associated
entries in the dsmonAggProfileTable shall be deleted.
This object MUST NOT be modified if the
dsmonAggControlLocked object is equal to 'true'."
::= { dsmonAggControlEntry 4 }
--
-- Counter Aggregation Profile Table
--
dsmonAggProfileTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonAggProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Controls the setup of counter aggregation profiles for this
agent. For each such profile, every DSCP value MUST be
configured into exactly one counter aggregation group.
This table MUST NOT be modified if the dsmonAggControlLocked
object is equal to 'true'.
The agent will create a set of 64 entries in this table
(with the same dsmonAggControlIndex value) when the
associated dsmonAggControlEntry is activated.
If the agent supports non-volatile configuration of this
table, then upon system initialization, this table SHOULD be
initialized with the saved values."
::= { dsmonAggObjects 6 }
dsmonAggProfileEntry OBJECT-TYPE
SYNTAX DsmonAggProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in the dsmonAggProfileTable. The
dsmonAggControlIndex value in the index identifies the
dsmonAggControlEntry associated with each entry in this
table."
INDEX { dsmonAggControlIndex, dsmonAggProfileDSCP }
::= { dsmonAggProfileTable 1 }
DsmonAggProfileEntry ::= SEQUENCE {
dsmonAggProfileDSCP Dscp,
dsmonAggGroupIndex DsmonCounterAggGroupIndex
}
dsmonAggProfileDSCP OBJECT-TYPE
SYNTAX Dscp
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The specific DSCP value for the DSCP counter which is
configured in a counter aggregation group by this entry."
::= { dsmonAggProfileEntry 1 }
dsmonAggGroupIndex OBJECT-TYPE
SYNTAX DsmonCounterAggGroupIndex
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The counter aggregation group which contains this DSCP
value. Upon creation of a new sub-tree (set of 64 entries
with the same dsmonAggControlIndex value) in this table, the
agent SHOULD initialize all related instances of this object
to the value zero.
This object MUST NOT be modified if the
dsmonAggControlLocked object is equal to 'true'."
DEFVAL { 0 }
::= { dsmonAggProfileEntry 2 }
--
-- Counter Aggregation Group Table
--
dsmonAggGroupTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonAggGroupEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides a description of each counter
aggregation group configured on this system. Note that the
semantics of a particular counter aggregation group are only
relevant within the scope of a particular counter
aggregation profile.
This table MUST NOT be modified if the dsmonAggControlLocked
object is equal to 'true'.
Note that an agent MAY choose to limit the actual number of
entries which may be created in this table, and
(independently) the number of counter aggregation profiles
which may be applied to a particular data source. In this
case, the agent SHOULD return an error-status of
'resourceUnavailable(13)', as per section 4.2.5 of the
'Protocol Operations for SNMPv2' specification [RFC1905].
If the agent supports non-volatile configuration of this
table, then upon system initialization, this table SHOULD be
initialized with the saved values. Otherwise, each
potential counter aggregation group description string
SHOULD contain the empty string.
An agent SHOULD allow entries to be created or modified in
this table, even if the specified dsmonAggControlIndex value
does not identify a valid dsmonAggControlEntry or a complete
set of valid dsmonAggProfileEntries, to reduce row creation
order dependencies."
::= { dsmonAggObjects 7 }
dsmonAggGroupEntry OBJECT-TYPE
SYNTAX DsmonAggGroupEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in the dsmonAggGroupTable. The
dsmonAggGroupIndex value in the INDEX identifies the counter
aggregation group associated with each entry.
The dsmonAggControlIndex in the index identifies the counter
aggregation profile associated with each entry, identified
by the dsmonAggControlEntry and dsmonAggProfileEntries with
the same index value.
The agent SHOULD support non-volatile configuration of this
table, and upon system initialization, the table SHOULD be
initialized with the saved values.
The dsmonAggGroupIndex in the index identifies the counter
aggregation group associated with each entry. This object
SHOULD be indexed from zero to 'N', where 'N' is less than
the value of the dsmonMaxAggGroups for this agent."
INDEX { dsmonAggControlIndex, dsmonAggGroupIndex }
::= { dsmonAggGroupTable 1 }
DsmonAggGroupEntry ::= SEQUENCE {
dsmonAggGroupDescr SnmpAdminString,
dsmonAggGroupStatus RowStatus
}
dsmonAggGroupDescr OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (0..64))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An administratively assigned description of the counter
aggregation group identified by this entry.
Upon first creation of an instance of this object, the agent
SHOULD set this object to the empty string.
This object MUST NOT be modified if the associated
dsmonAggGroupStatus object is equal to 'active', or the
dsmonAggControlLocked object is equal to 'true'."
::= { dsmonAggGroupEntry 1 }
dsmonAggGroupStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this row.
An entry MUST NOT exist in the active state unless all
objects in the entry have an appropriate value.
This object MUST NOT be modified if the
dsmonAggControlLocked object is equal to 'true'."
::= { dsmonAggGroupEntry 2 }
-- *************************************************************
-- * *
-- * P E R - D A T A S O U R C E C O L L E C T I O N S *
-- * *
-- *************************************************************
--
-- Per-DataSource Statistics Control Table
--
dsmonStatsControlTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonStatsControlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Controls the setup of per data source per counter
aggregation group distribution statistics.
Note that an agent MAY choose to limit the actual number of
entries which may be created in this table. In this case,
the agent SHOULD return an error-status of
'resourceUnavailable(13)', as per section 4.2.5 of the
'Protocol Operations for SNMPv2' specification [RFC1905]."
::= { dsmonStatsObjects 1 }
dsmonStatsControlEntry OBJECT-TYPE
SYNTAX DsmonStatsControlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in the dsmonStatsControlTable.
Entries are created and deleted from this table by
management action only, using the dsmonStatsControlStatus
RowStatus object.
The agent SHOULD support non-volatile configuration of this
table, and upon system initialization, the table SHOULD be
initialized with the saved values.
Activation of a control row in this table will cause an
associated dsmonStatsTable to be created and maintained by
the agent."
INDEX { dsmonStatsControlIndex }
::= { dsmonStatsControlTable 1 }
DsmonStatsControlEntry ::= SEQUENCE {
dsmonStatsControlIndex Integer32,
dsmonStatsControlDataSource DataSource,
dsmonStatsControlAggProfile DsmonCounterAggProfileIndex,
dsmonStatsControlDroppedFrames Counter32,
dsmonStatsControlCreateTime LastCreateTime,
dsmonStatsControlOwner OwnerString,
dsmonStatsControlStatus RowStatus
}
dsmonStatsControlIndex OBJECT-TYPE
SYNTAX Integer32 (1..65535)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An arbitrary and unique index for this
dsmonStatsControlEntry."
::= { dsmonStatsControlEntry 1 }
dsmonStatsControlDataSource OBJECT-TYPE
SYNTAX DataSource
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The data source of this per protocol per counter
aggregation group distribution.
Note that only packets that contain a network protocol
encapsulation which contains a DS field [RFC2474] will be
counted in this table.
This object MUST NOT be modified if the associated
dsmonStatsControlStatus object is equal to active(1)."
::= { dsmonStatsControlEntry 2 }
dsmonStatsControlAggProfile OBJECT-TYPE
SYNTAX DsmonCounterAggProfileIndex
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The dsmonAggControlIndex value identifying the counter
aggregation profile which should be used on behalf of this
dsmonStatsControlEntry.
The associated dsmonAggControlEntry and
dsmonAggProfileEntries, identified by the same
dsmonAggControlIndex index value, MUST be active in order
for this entry to remain active. It is possible for the
counter aggregation configuration to change from a valid to
invalid state for this dsmonStats collection. In this case,
the associated dsmonStatsControlStatus object will be
changed to the 'notReady' state, and data collection will
not occur on behalf of this control entry.
Note that an agent MAY choose to limit the actual number of
counter aggregation profiles which may be applied to a
particular data source.
This object MUST NOT be modified if the associated
dsmonStatsControlStatus object is equal to active(1)."
::= { dsmonStatsControlEntry 3 }
dsmonStatsControlDroppedFrames OBJECT-TYPE
SYNTAX Counter32
UNITS "frames"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of frames which were received by the probe
and therefore not accounted for in the *StatsDropEvents, but
for which the probe chose not to count for this entry for
whatever reason. Most often, this event occurs when the
probe is out of some resources and decides to shed load from
this collection.
This count does not include packets that were not counted
because they had MAC-layer errors.
Note that, unlike the dropEvents counter, this number is the
exact number of frames dropped."
::= { dsmonStatsControlEntry 4 }
dsmonStatsControlCreateTime OBJECT-TYPE
SYNTAX LastCreateTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime when this control entry was last
activated. This can be used by the management station to
detect if the table has been deleted and recreated between
polls."
::= { dsmonStatsControlEntry 5 }
dsmonStatsControlOwner OBJECT-TYPE
SYNTAX OwnerString
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The entity that configured this entry and is therefore
using the resources assigned to it."
::= { dsmonStatsControlEntry 6 }
dsmonStatsControlStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this row.
An entry MUST NOT exist in the active state unless all
objects in the entry have an appropriate value.
If this object is not equal to active(1), all associated
entries in the dsmonStatsTable shall be deleted."
::= { dsmonStatsControlEntry 7 }
--
-- Per-DataSource Statistics Table
--
dsmonStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of information on counter aggregation group usage
for each monitored data source.
The following table defines per counter aggregation group
statistics for full and/or half-duplex links as well as high
capacity links.
For half-duplex links, or full-duplex-capable links
operating in half-duplex mode, the dsmonStatsIn* objects
shall be used and the dsmonStatsOut* objects will not
increment.
For full-duplex links, the dsmonStatsOut* objects will be
present. Whenever possible, the probe SHOULD count packets
moving away from the closest terminating equipment as output
packets. Failing that, the probe SHOULD count packets
moving away from the DTE as output packets.
If the dsmonAggControlLocked object is equal to 'false',
then all entries in this table will be deleted and the agent
will not process packets on behalf of any
dsmonStatsControlEntry."
::= { dsmonStatsObjects 2 }
dsmonStatsEntry OBJECT-TYPE
SYNTAX DsmonStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of information on Differentiated Services DSCP
usage, containing inbound and outbound packet and octet
counters for each counter aggregation group configured for
collection.
The dsmonStatsControlIndex value in the index identifies the
dsmonStatsControlEntry on whose behalf this entry was
created.
The dsmonAggGroupIndex value in the index is determined by
examining the DSCP value in each monitored packet, and the
dsmonAggProfileTable entry for that DSCP value.
Note that only packets that contain a network protocol
encapsulation which contains a DS field [RFC2474] will be
counted in this table.
An example of the indexing of this entry is
dsmonStatsOutPkts.1.16"
INDEX { dsmonStatsControlIndex, dsmonAggGroupIndex }
::= { dsmonStatsTable 1 }
DsmonStatsEntry ::= SEQUENCE {
dsmonStatsInPkts ZeroBasedCounter32,
dsmonStatsInOctets ZeroBasedCounter32,
dsmonStatsInOvflPkts ZeroBasedCounter32,
dsmonStatsInOvflOctets ZeroBasedCounter32,
dsmonStatsInHCPkts ZeroBasedCounter64,
dsmonStatsInHCOctets ZeroBasedCounter64,
dsmonStatsOutPkts ZeroBasedCounter32,
dsmonStatsOutOctets ZeroBasedCounter32,
dsmonStatsOutOvflPkts ZeroBasedCounter32,
dsmonStatsOutOvflOctets ZeroBasedCounter32,
dsmonStatsOutHCPkts ZeroBasedCounter64,
dsmonStatsOutHCOctets ZeroBasedCounter64
}
dsmonStatsInPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of packets using one of the DSCP values in the
indicated counter aggregation group, received on a half-
duplex link or on the inbound connection of a full-duplex
link."
::= { dsmonStatsEntry 1 }
dsmonStatsInOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets in packets, using one of the DSCP
values in the indicated counter aggregation group, received
on a half-duplex link or on the inbound connection of a
full-duplex link."
::= { dsmonStatsEntry 2 }
dsmonStatsInOvflPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of times the associated dsmonStatsInPkts counter
has overflowed. Note that this object will only be
instantiated if the associated dsmonStatsInHCPkts object is
also instantiated for a particular dataSource."
::= { dsmonStatsEntry 3 }
dsmonStatsInOvflOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of times the associated dsmonStatsInOctets
counter has overflowed. Note that this object will only be
instantiated if the associated dsmonStatsInHCOctets object
is also instantiated for a particular dataSource."
::= { dsmonStatsEntry 4 }
dsmonStatsInHCPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter64
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 64-bit version of the dsmonStatsInPkts object.
Note that this object will only be instantiated if the RMON
agent supports High Capacity monitoring for a particular
dataSource."
::= { dsmonStatsEntry 5 }
dsmonStatsInHCOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter64
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 64-bit version of the dsmonStatsInOctets object.
Note that this object will only be instantiated if the RMON
agent supports High Capacity monitoring for a particular
dataSource."
::= { dsmonStatsEntry 6 }
dsmonStatsOutPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of packets using one of the DSCP values in the
indicated counter aggregation group, received on a full-
duplex link in the direction of the network."
::= { dsmonStatsEntry 7 }
dsmonStatsOutOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets in packets, using one of the DSCP
values in the indicated counter aggregation group, received
on a full-duplex link in the direction of the network."
::= { dsmonStatsEntry 8 }
dsmonStatsOutOvflPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of times the associated dsmonStatsOutPkts
counter has overflowed. Note that this object will only be
instantiated if the associated dsmonStatsOutHCPkts object is
also instantiated for a particular dataSource."
::= { dsmonStatsEntry 9 }
dsmonStatsOutOvflOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of times the associated dsmonStatsOutOctets
counter has overflowed. Note that this object will only be
instantiated if the associated dsmonStatsOutHCOctets object
is also instantiated for a particular dataSource."
::= { dsmonStatsEntry 10 }
dsmonStatsOutHCPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter64
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 64-bit version of the dsmonStatsOutPkts object.
Note that this object will only be instantiated if the RMON
agent supports High Capacity monitoring for a particular
dataSource."
::= { dsmonStatsEntry 11 }
dsmonStatsOutHCOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter64
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 64-bit version of the dsmonStatsOutOctets object.
Note that this object will only be instantiated if the RMON
agent supports High Capacity monitoring for a particular
dataSource."
::= { dsmonStatsEntry 12 }
-- ***********************************************************
-- * *
-- * P E R - P R O T O C O L C O L L E C T I O N S *
-- * *
-- ***********************************************************
--
-- DSCP Per-Protocol Statistics Control Table
--
dsmonPdistCtlTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonPdistCtlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Controls the setup of per application per counter
aggregation group distribution statistics.
Note that an agent MAY choose to limit the actual number of
entries which may be created in this table. In this case,
the agent SHOULD return an error-status of
'resourceUnavailable(13)', as per section 4.2.5 of the
'Protocol Operations for SNMPv2' specification [RFC1905]."
::= { dsmonPdistObjects 1 }
dsmonPdistCtlEntry OBJECT-TYPE
SYNTAX DsmonPdistCtlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in the dsmonPdistCtlTable.
Entries are created and deleted from this table by
management action only, using the dsmonPdistCtlStatus
RowStatus object.
The agent SHOULD support non-volatile configuration of this
table, and upon system initialization, the table SHOULD be
initialized with the saved values.
Activation of a control row in this table will cause an
associated dsmonPdistStatsTable to be created and maintained
by the agent."
INDEX { dsmonPdistCtlIndex }
::= { dsmonPdistCtlTable 1 }
DsmonPdistCtlEntry ::= SEQUENCE {
dsmonPdistCtlIndex Integer32,
dsmonPdistCtlDataSource DataSource,
dsmonPdistCtlAggProfile DsmonCounterAggProfileIndex,
dsmonPdistCtlMaxDesiredEntries Integer32,
dsmonPdistCtlDroppedFrames Counter32,
dsmonPdistCtlInserts Counter32,
dsmonPdistCtlDeletes Counter32,
dsmonPdistCtlCreateTime LastCreateTime,
dsmonPdistCtlOwner OwnerString,
dsmonPdistCtlStatus RowStatus
}
dsmonPdistCtlIndex OBJECT-TYPE
SYNTAX Integer32 (1..65535)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An arbitrary and unique index for this dsmonPdistCtlEntry."
::= { dsmonPdistCtlEntry 1 }
dsmonPdistCtlDataSource OBJECT-TYPE
SYNTAX DataSource
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The source of data for the this per protocol counter
aggregation group distribution.
This object MUST NOT be modified if the associated
dsmonPdistCtlStatus object is equal to active(1)."
::= { dsmonPdistCtlEntry 2 }
dsmonPdistCtlAggProfile OBJECT-TYPE
SYNTAX DsmonCounterAggProfileIndex
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The dsmonAggControlIndex value identifying the counter
aggregation profile which should be used on behalf of this
dsmonPdistCtlEntry.
The associated dsmonAggControlEntry and
dsmonAggProfileEntries, identified by the same
dsmonAggControlIndex index value, MUST be active in order
for this entry to remain active. It is possible for the
counter aggregation configuration to change from a valid to
invalid state for this dsmonPdist collection. In this case,
the associated dsmonPdistCtlStatus object will be changed to
the 'notReady' state, and data collection will not occur on
behalf of this control entry.
Note that an agent MAY choose to limit the actual number of
counter aggregation profiles which may be applied to a
particular data source.
This object MUST NOT be modified if the associated
dsmonPdistCtlStatus object is equal to active(1)."
::= { dsmonPdistCtlEntry 3 }
dsmonPdistCtlMaxDesiredEntries OBJECT-TYPE
SYNTAX Integer32 (-1 | 1..2147483647)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum number of entries that are desired in the
dsmonPdistStatsTable on behalf of this control entry. The
probe will not create more than this number of associated
entries in the table, but MAY choose to create fewer entries
in this table for any reason including the lack of
resources.
If this value is set to -1, the probe MAY create any number
of entries in this table.
This object MUST NOT be modified if the associated
dsmonPdistCtlStatus object is equal to active(1)."
::= { dsmonPdistCtlEntry 4 }
dsmonPdistCtlDroppedFrames OBJECT-TYPE
SYNTAX Counter32
UNITS "frames"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of frames which were received by the probe
and therefore not accounted for in the *StatsDropEvents, but
for which the probe chose not to count for this entry for
whatever reason. Most often, this event occurs when the
probe is out of some resources and decides to shed load from
this collection.
This count does not include packets that were not counted
because they had MAC-layer errors.
Note that, unlike the dropEvents counter, this number is the
exact number of frames dropped."
::= { dsmonPdistCtlEntry 5 }
dsmonPdistCtlInserts OBJECT-TYPE
SYNTAX Counter32
UNITS "table entries"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times a dsmonPdist entry has been inserted
into the dsmonPdistTable. If an entry is inserted, then
deleted, and then inserted, this counter will be incremented
by 2.
To allow for efficient implementation strategies, agents MAY
delay updating this object for short periods of time. For
example, an implementation strategy may allow internal data
structures to differ from those visible via SNMP for short
periods of time. This counter may reflect the internal data
structures for those short periods of time.
Note that the table size can be determined by subtracting
dsmonPdistCtlDeletes from dsmonPdistCtlInserts."
::= { dsmonPdistCtlEntry 6 }
dsmonPdistCtlDeletes OBJECT-TYPE
SYNTAX Counter32
UNITS "table entries"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times a dsmonPdist entry has been deleted
from the dsmonPdist table (for any reason). If an entry is
deleted, then inserted, and then deleted, this counter will
be incremented by 2.
To allow for efficient implementation strategies, agents MAY
delay updating this object for short periods of time. For
example, an implementation strategy may allow internal data
structures to differ from those visible via SNMP for short
periods of time. This counter may reflect the internal data
structures for those short periods of time.
Note that the table size can be determined by subtracting
dsmonPdistCtlDeletes from dsmonPdistCtlInserts."
::= { dsmonPdistCtlEntry 7 }
dsmonPdistCtlCreateTime OBJECT-TYPE
SYNTAX LastCreateTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime when this control entry was last
activated. This can be used by the management station to
detect if the table has been deleted and recreated between
polls."
::= { dsmonPdistCtlEntry 8 }
dsmonPdistCtlOwner OBJECT-TYPE
SYNTAX OwnerString
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The entity that configured this entry and is therefore
using the resources assigned to it."
::= { dsmonPdistCtlEntry 9 }
dsmonPdistCtlStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this row.
An entry MUST NOT exist in the active state unless all
objects in the entry have an appropriate value.
If this object is not equal to active(1), all associated
entries in the dsmonPdistStatsTable shall be deleted."
::= { dsmonPdistCtlEntry 10 }
--
-- Per-Protocol Statistics Table
--
dsmonPdistStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonPdistStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of information on a per protocol per counter
aggregation group usage.
If the dsmonAggControlLocked object is equal to 'false',
then all entries in this table will be deleted and the agent
will not process packets on behalf of any
dsmonPdistCtlEntry."
::= { dsmonPdistObjects 2 }
dsmonPdistStatsEntry OBJECT-TYPE
SYNTAX DsmonPdistStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of information on Differentiated Services DSCP
usage, containing packet and octet counters for each counter
aggregation group configured for collection, and each
protocol (as identified by the protocolDirLocalIndex for the
protocol) identified in each monitored packet.
The dsmonPdistCtlIndex value in the index identifies the
dsmonPdistCtlEntry on whose behalf this entry was created.
Note that only packets that contain a network protocol
encapsulation which contains a DS field [RFC2474] will be
counted in this table.
The dsmonAggGroupIndex value in the index is determined by
examining the DSCP value in each monitored packet, and the
dsmonAggProfileTable entry for that value.
The protocolDirLocalIndex in the index identifies the
protocolDirEntry for the protocol encapsulation of each
monitored packet. The agent will include only application
layer protocols in the associated dsmonPdistStatsTable. Any
'terminal' protocol is considered to be an application
protocol.
An example of the indexing of this entry is
dsmonPdistStatsPkts.9.29943.0.42."
INDEX { dsmonPdistCtlIndex,
dsmonPdistTimeMark,
dsmonAggGroupIndex,
protocolDirLocalIndex }
::= { dsmonPdistStatsTable 1 }
DsmonPdistStatsEntry ::= SEQUENCE {
dsmonPdistTimeMark TimeFilter,
dsmonPdistStatsPkts ZeroBasedCounter32,
dsmonPdistStatsOctets ZeroBasedCounter32,
dsmonPdistStatsOvflPkts ZeroBasedCounter32,
dsmonPdistStatsOvflOctets ZeroBasedCounter32,
dsmonPdistStatsHCPkts ZeroBasedCounter64,
dsmonPdistStatsHCOctets ZeroBasedCounter64,
dsmonPdistStatsCreateTime LastCreateTime
}
dsmonPdistTimeMark OBJECT-TYPE
SYNTAX TimeFilter
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Time Filter index for this table. This object may be
used by a management station to retrieve only rows which
have been created or modified since a particular time. Note
that the current value for a row are always returned and the
TimeFilter is not a historical data archiving mechanism.
Refer to RFC 2021 [RFC2021] for a detailed description of
TimeFilter operation."
::= { dsmonPdistStatsEntry 1 }
dsmonPdistStatsPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of packets, using one of the DSCP values in the
indicated counter aggregation group, for the protocol
identified by the associated protocolDirLocalIndex value."
::= { dsmonPdistStatsEntry 2 }
dsmonPdistStatsOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets in packets, using one of the DSCP
values in the indicated counter aggregation group, for the
protocol identified by the associated protocolDirLocalIndex
value.
Note that this object doesn't count just those octets in the
particular protocol frames, but includes the entire packet
that contained the protocol."
::= { dsmonPdistStatsEntry 3 }
dsmonPdistStatsOvflPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of times the associated dsmonPdistStatsPkts
counter has overflowed. Note that this object will only be
instantiated if the associated dsmonPdistStatsHCPkts object
is also instantiated for a particular dataSource."
::= { dsmonPdistStatsEntry 4 }
dsmonPdistStatsOvflOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of times the associated dsmonPdistStatsOctets
counter has overflowed. Note that this object will only be
instantiated if the associated dsmonPdistStatsHCOctets
object is also instantiated for a particular dataSource."
::= { dsmonPdistStatsEntry 5 }
dsmonPdistStatsHCPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter64
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 64-bit version of the dsmonPdistStatsPkts object.
Note that this object will only be instantiated if the RMON
agent supports High Capacity monitoring for a particular
dataSource."
::= { dsmonPdistStatsEntry 6 }
dsmonPdistStatsHCOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter64
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 64-bit version of the dsmonPdistStatsOctets object.
Note that this object will only be instantiated if the RMON
agent supports High Capacity monitoring for a particular
dataSource."
::= { dsmonPdistStatsEntry 7 }
dsmonPdistStatsCreateTime OBJECT-TYPE
SYNTAX LastCreateTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime when this dsmonPdistStats entry was
last instantiated by the agent. This can be used by the
management station to detect if the entry has been deleted
and recreated between polls."
::= { dsmonPdistStatsEntry 8 }
--
-- Per-Protocol Statistics TopN Control Table
--
dsmonPdistTopNCtlTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonPdistTopNCtlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A set of parameters that control the creation of a report
of the top N dsmonPdist entries according to a particular
metric.
Note that an agent MAY choose to limit the actual number of
entries which may be created in this table. In this case,
the agent SHOULD return an error-status of
'resourceUnavailable(13)', as per section 4.2.5 of the
'Protocol Operations for SNMPv2' specification [RFC1905]."
::= { dsmonPdistObjects 3 }
dsmonPdistTopNCtlEntry OBJECT-TYPE
SYNTAX DsmonPdistTopNCtlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in the dsmonPdistTopNCtlTable.
Entries are created and deleted from this table by
management action only, using the dsmonPdistTopNCtlStatus
RowStatus object.
The agent SHOULD support non-volatile configuration of this
table, and upon system initialization, the table SHOULD be
initialized with the saved values.
Activation of a control row in this table will cause an
associated dsmonPdistTopNTable to be created and maintained
by the agent."
INDEX { dsmonPdistTopNCtlIndex }
::= { dsmonPdistTopNCtlTable 1 }
DsmonPdistTopNCtlEntry ::= SEQUENCE {
dsmonPdistTopNCtlIndex Integer32,
dsmonPdistTopNCtlPdistIndex Integer32,
dsmonPdistTopNCtlRateBase INTEGER,
dsmonPdistTopNCtlTimeRemaining Integer32,
dsmonPdistTopNCtlGeneratedReprts Counter32,
dsmonPdistTopNCtlDuration Integer32,
dsmonPdistTopNCtlRequestedSize Integer32,
dsmonPdistTopNCtlGrantedSize Integer32,
dsmonPdistTopNCtlStartTime TimeStamp,
dsmonPdistTopNCtlOwner OwnerString,
dsmonPdistTopNCtlStatus RowStatus
}
dsmonPdistTopNCtlIndex OBJECT-TYPE
SYNTAX Integer32 (1..65535)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An index that uniquely identifies an entry in the
dsmonPdistTopNCtlTable, with the same dsmonPdistTopNCtlIndex
value as this object. Each entry in this table defines one
Top N report prepared on behalf of the dsmonPdistStatsEntry
collection with the same dsmonPdistCtlIndex as this object."
::= { dsmonPdistTopNCtlEntry 1 }
dsmonPdistTopNCtlPdistIndex OBJECT-TYPE
SYNTAX Integer32 (1..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The dsmonPdistTable for which a top N report will be
prepared on behalf of this entry. The dsmonPdistTable is
identified by the value of the dsmonPdistCtlIndex for that
table - that value is used here to identify the particular
table.
This object MUST NOT be modified if the associated
dsmonPdistTopNCtlStatus object is equal to active(1)."
::= { dsmonPdistTopNCtlEntry 2 }
dsmonPdistTopNCtlRateBase OBJECT-TYPE
SYNTAX INTEGER {
dsmonPdistTopNPkts(1),
dsmonPdistTopNOctets(2),
dsmonPdistTopNHCPkts(3),
dsmonPdistTopNHCOctets(4)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The variable for each dsmonPdist that the
dsmonPdistTopNRate and dsmonPdistTopNHCRate variables are
based upon. Each dsmonPdistTopN report generated on behalf
of this control entry will be ranked in descending order,
based on the associated dsmonPdistStatsTable counter,
identified by this object.
The following table identifies the dsmonPdistTable counter
associated with each enumeration:
Enumeration RateBase MIB Object
----------- -------------------
dsmonPdistTopNPkts dsmonPdistStatsPkts
dsmonPdistTopNOctets dsmonPdistStatsOctets
dsmonPdistTopNHCPkts dsmonPdistStatsHCPkts
dsmonPdistTopNHCOctets dsmonPdistStatsHCOctets
Note that the dsmonPdistTopNHCPkts and
dsmonPdistTopNHCOctets enumerations are only available if
the agent supports High Capacity monitoring.
This object MUST NOT be modified if the associated
dsmonPdistTopNCtlStatus object is equal to active(1)."
::= { dsmonPdistTopNCtlEntry 3 }
dsmonPdistTopNCtlTimeRemaining OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The number of seconds left in the report currently being
collected. When this object is modified by the management
station, a new collection is started, possibly aborting a
currently running report. The new value is used as the
requested duration of this report, and is immediately loaded
into the associated dsmonPdistTopNCtlDuration object.
When the report finishes, the probe will automatically start
another collection with the same initial value of
dsmonPdistTopNCtlTimeRemaining. Thus the management station
may simply read the resulting reports repeatedly, checking
the startTime and duration each time to ensure that a report
was not missed or that the report parameters were not
changed.
While the value of this object is non-zero, it decrements by
one per second until it reaches zero. At the time that this
object decrements to zero, the report is made accessible in
the dsmonPdistTopNTable, overwriting any report that may be
there.
When this object is modified by the management station, any
associated entries in the dsmonPdistTopNTable shall be
deleted."
DEFVAL { 1800 }
::= { dsmonPdistTopNCtlEntry 4 }
dsmonPdistTopNCtlGeneratedReprts OBJECT-TYPE
SYNTAX Counter32
UNITS "reports"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of reports that have been generated by this
entry."
::= { dsmonPdistTopNCtlEntry 5 }
dsmonPdistTopNCtlDuration OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of seconds that this report has collected during
the last sampling interval.
When the associated dsmonPdistTopNCtlTimeRemaining object is
set, this object shall be set by the probe to the same value
and shall not be modified until the next time the
dsmonPdistTopNCtlTimeRemaining is set.
This value shall be zero if no reports have been requested
for this dsmonPdistTopNCtlEntry."
::= { dsmonPdistTopNCtlEntry 6 }
dsmonPdistTopNCtlRequestedSize OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
UNITS "table entries"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum number of dsmonPdist entries requested for this
report.
When this object is created or modified, the probe SHOULD
set dsmonPdistTopNCtlGrantedSize as closely to this object
as is possible for the particular probe implementation and
available resources."
DEFVAL { 150 }
::= { dsmonPdistTopNCtlEntry 7 }
dsmonPdistTopNCtlGrantedSize OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
UNITS "table entries"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum number of dsmonPdist entries in this report.
When the associated dsmonPdistTopNCtlRequestedSize object is
created or modified, the probe SHOULD set this object as
closely to the requested value as is possible for the
particular implementation and available resources. The
probe MUST NOT lower this value except as a result of a
set to the associated dsmonPdistTopNCtlRequestedSize
object.
Protocol entries with the highest value of
dsmonPdistTopNRate or dsmonPdistTopNHCRate (depending on the
value of the associated dsmonPdistTopNCtlRateBase object)
shall be placed in this table in decreasing order of this
rate until there is no more room or until there are no more
dsmonPdist entries."
::= { dsmonPdistTopNCtlEntry 8 }
dsmonPdistTopNCtlStartTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime when this top N report was last
started. In other words, this is the time that the
associated dsmonPdistTopNCtlTimeRemaining object was
modified to start the requested report or the time the
report was last automatically (re)started.
This object may be used by the management station to
determine if a report was missed or not."
::= { dsmonPdistTopNCtlEntry 9 }
dsmonPdistTopNCtlOwner OBJECT-TYPE
SYNTAX OwnerString
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The entity that configured this entry and is therefore
using the resources assigned to it."
::= { dsmonPdistTopNCtlEntry 10 }
dsmonPdistTopNCtlStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this dsmonPdistTopNCtlEntry.
An entry MUST NOT exist in the active state unless all
objects in the entry have an appropriate value.
If this object is not equal to active(1), all associated
entries in the dsmonPdistTopNTable shall be deleted by the
agent."
::= { dsmonPdistTopNCtlEntry 11 }
--
-- dsmonPdist TopN Table
--
dsmonPdistTopNTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonPdistTopNEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A set of statistics for those protocol distribution entries
that have counted the highest number of octets or packets.
If the dsmonAggControlLocked object is equal to 'false',
then all entries in this table SHALL be deleted, and the
agent will not process TopN reports on behalf of any
dsmonPdistTopNCtlEntry.
When the dsmonAggControlLocked object is set to 'true', then
particular reports SHOULD be restarted from the beginning,
on behalf of all active rows in the dsmonPdistTopNCtlTable.
Note that dsmonPdist entries which did not increment at all
during the report interval SHOULD NOT be included in
dsmonPdistTopN reports."
::= { dsmonPdistObjects 4 }
dsmonPdistTopNEntry OBJECT-TYPE
SYNTAX DsmonPdistTopNEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in the dsmonPdistTopNTable.
The dsmonPdistTopNCtlIndex value in the index identifies the
dsmonPdistTopNCtlEntry on whose behalf this entry was
created. Entries in this table are ordered from 1 to 'N',
where lower numbers represent higher values of the rate base
object, over the report interval."
INDEX { dsmonPdistTopNCtlIndex, dsmonPdistTopNIndex }
::= { dsmonPdistTopNTable 1 }
DsmonPdistTopNEntry ::= SEQUENCE {
dsmonPdistTopNIndex Integer32,
dsmonPdistTopNPDLocalIndex Integer32,
dsmonPdistTopNAggGroup DsmonCounterAggGroupIndex,
dsmonPdistTopNRate Gauge32,
dsmonPdistTopNRateOvfl Gauge32,
dsmonPdistTopNHCRate CounterBasedGauge64
}
dsmonPdistTopNIndex OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An index that uniquely identifies an entry in the
dsmonPdistTopNTable among those in the same report. This
index is between 1 and N, where N is the number of entries
in this report. Note that 'N' may change over time, and may
also be less than the dsmonPdistTopNCtlGrantedSize value
associated with this entry."
::= { dsmonPdistTopNEntry 1 }
dsmonPdistTopNPDLocalIndex OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The protocolDirLocalIndex value which identifies the
protocol associated with this entry.
If the protocolDirEntry associated with the
protocolDirLocalIndex with the same value as this object is
de-activated or deleted, then the agent MUST delete this
dsmonPdistTopN entry."
::= { dsmonPdistTopNEntry 2 }
dsmonPdistTopNAggGroup OBJECT-TYPE
SYNTAX DsmonCounterAggGroupIndex
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The DSCP counter aggregation group index value associated
with protocol identified in this entry. This object
identifies the dsmonAggGroupEntry with the same
dsmonAggControlIndex value as the associated
dsmonPdistCtlAggProfile object and the same
dsmonAggGroupIndex value as this object."
::= { dsmonPdistTopNEntry 3 }
dsmonPdistTopNRate OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The amount of change in the selected variable during this
sampling interval. The selected variable is this protocol's
instance of the object selected by
dsmonPdistTopNCtlRateBase.
If the associated dsmonPdistTopNCtlRateBase is equal to
'dsmonPdistTopNHCPkts' or 'dsmonPdistTopNHCOctets', then
this object will contain the the least significant 32 bits
of the associated dsmonPdistTopNHCRate object."
::= { dsmonPdistTopNEntry 4 }
dsmonPdistTopNRateOvfl OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The most significant 32 bits of the associated
dsmonPdistTopNHCRate object.
If the associated dsmonPdistTopNCtlRateBase is equal to
'dsmonPdistTopNHCPkts' or 'dsmonPdistTopNHCOctets', then
this object will contain the upper 32 bits of the associated
dsmonPdistTopNHCRate object.
If the associated dsmonPdistTopNCtlRateBase is equal to
'dsmonPdistTopNPkts' or 'dsmonPdistTopNOctets', then this
object will contain the value zero.
The agent MAY choose not to instantiate this object if High
Capacity monitoring is not supported."
::= { dsmonPdistTopNEntry 5 }
dsmonPdistTopNHCRate OBJECT-TYPE
SYNTAX CounterBasedGauge64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The amount of change in the selected variable during this
sampling interval. The selected variable is this protocol's
instance of the object selected by
dsmonPdistTopNCtlRateBase.
If the associated dsmonPdistTopNCtlRateBase is equal to
'dsmonPdistTopNPkts' or 'dsmonPdistTopNOctets', then this
object will contain the value zero, and the associated
dsmonPdistTopNRate object will contain the change in the
selected variable during the sampling interval.
The agent MAY choose not to instantiate this object if High
Capacity monitoring is not supported."
::= { dsmonPdistTopNEntry 6 }
-- ***********************************************************
-- * *
-- * P E R - H O S T C O L L E C T I O N S *
-- * *
-- ***********************************************************
--
-- NL Host Statistics Control Table
--
dsmonHostCtlTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonHostCtlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Controls setup of per counter aggregation group, per
network layer host distribution statistics.
Note that an agent MAY choose to limit the actual number of
entries which may be created in this table. In this case,
the agent SHOULD return an error-status of
'resourceUnavailable(13)', as per section 4.2.5 of the
'Protocol Operations for SNMPv2' specification [RFC1905]."
::= { dsmonHostObjects 1 }
dsmonHostCtlEntry OBJECT-TYPE
SYNTAX DsmonHostCtlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in the dsmonHostCtlTable.
Entries are created and deleted from this table by
management action only, using the dsmonHostCtlStatus
RowStatus object.
The agent SHOULD support non-volatile configuration of this
table, and upon system initialization, the table SHOULD be
initialized with the saved values.
Activation of a control row in this table will cause an
associated dsmonHostTable to be created and maintained by
the agent."
INDEX { dsmonHostCtlIndex }
::= { dsmonHostCtlTable 1 }
DsmonHostCtlEntry ::= SEQUENCE {
dsmonHostCtlIndex Integer32,
dsmonHostCtlDataSource DataSource,
dsmonHostCtlAggProfile DsmonCounterAggProfileIndex,
dsmonHostCtlMaxDesiredEntries Integer32,
dsmonHostCtlIPv4PrefixLen Integer32,
dsmonHostCtlIPv6PrefixLen Integer32,
dsmonHostCtlDroppedFrames Counter32,
dsmonHostCtlInserts Counter32,
dsmonHostCtlDeletes Counter32,
dsmonHostCtlCreateTime LastCreateTime,
dsmonHostCtlOwner OwnerString,
dsmonHostCtlStatus RowStatus
}
dsmonHostCtlIndex OBJECT-TYPE
SYNTAX Integer32 (1..65535)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An arbitrary and unique index for this dsmonHostCtlEntry."
::= { dsmonHostCtlEntry 1 }
dsmonHostCtlDataSource OBJECT-TYPE
SYNTAX DataSource
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The source of data for the associated dsmonHostTable.
Note that only packets that contain a network protocol
encapsulation which contains a DS field [RFC2474] will be
counted in this table.
This object MUST NOT be modified if the associated
dsmonHostCtlStatus object is equal to active(1)."
::= { dsmonHostCtlEntry 2 }
dsmonHostCtlAggProfile OBJECT-TYPE
SYNTAX DsmonCounterAggProfileIndex
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The dsmonAggControlIndex value identifying the counter
aggregation profile which should be used on behalf of this
dsmonHostCtlEntry.
The associated dsmonAggControlEntry and
dsmonAggProfileEntries, identified by the same
dsmonAggControlIndex index value, MUST be active in order
for this entry to remain active. It is possible for the
counter aggregation configuration to change from a valid to
invalid state for this dsmonHost collection. In this case,
the associated dsmonHostCtlStatus object will be changed to
the 'notReady' state, and data collection will not occur on
behalf of this control entry.
Note that an agent MAY choose to limit the actual number of
counter aggregation profiles which may be applied to a
particular data source.
This object MUST NOT be modified if the associated
dsmonHostCtlStatus object is equal to active(1)."
::= { dsmonHostCtlEntry 3 }
dsmonHostCtlMaxDesiredEntries OBJECT-TYPE
SYNTAX Integer32 (-1 | 1..2147483647)
UNITS "table entries"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum number of entries that are desired in the
dsmonHostTable on behalf of this control entry. The probe
will not create more than this number of associated entries
in the table, but MAY choose to create fewer entries in this
table for any reason including the lack of resources.
If this value is set to -1, the probe MAY create any number
of entries in this table.
This object MUST NOT be modified if the associated
dsmonHostCtlStatus object is equal to active(1)."
::= { dsmonHostCtlEntry 4 }
dsmonHostCtlIPv4PrefixLen OBJECT-TYPE
SYNTAX Integer32 (8..32)
UNITS "bits"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The number of 'leftmost' contiguous bits in the host
address field for encapsulations of IPv4, that should be
maintained in this collection. This object controls how the
dsmonHostAddress object is derived for packets which contain
an encapsulation of IPv4.
If this object has a value less than 32, then 'm' rightmost
bits, where 'm' is equal to '32 -
dsmonHostCtlIPv4PrefixLen', will be cleared to zero for
counting purposes only. The 'leftmost' bit is the most
significant bit of the first network-byte-order octet of the
address.
If this object is equal to 32, then no bits are cleared in
each dsmonHostAddress field.
This object MUST NOT be modified if the associated
dsmonHostCtlStatus object is equal to active(1)."
DEFVAL { 32 }
::= { dsmonHostCtlEntry 5 }
dsmonHostCtlIPv6PrefixLen OBJECT-TYPE
SYNTAX Integer32 (8..128)
UNITS "bits"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The number of 'leftmost' contiguous bits in the host
address field for encapsulations of IPv6, that should be
maintained in this collection. This object controls how the
dsmonHostAddress object is derived for packets which contain
an encapsulation of IPv6.
If this object has a value less than 128, then 'm' rightmost
bits, where 'm' is equal to '128 -
dsmonHostCtlIPv6PrefixLen', will be cleared to zero for
counting purposes only. The 'leftmost' bit is the most
significant bit of the first network-byte-order octet of the
address.
If this object is equal to 128, then no bits are cleared in
each dsmonHostAddress field.
This object MUST NOT be modified if the associated
dsmonHostCtlStatus object is equal to active(1)."
DEFVAL { 128 }
::= { dsmonHostCtlEntry 6 }
dsmonHostCtlDroppedFrames OBJECT-TYPE
SYNTAX Counter32
UNITS "frames"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of frames which were received by the probe
and therefore not accounted for in the *StatsDropEvents, but
for which the probe chose not to count for the associated
dsmonHost entries for whatever reason. Most often, this
event occurs when the probe is out of some resources and
decides to shed load from this collection.
This count does not include packets that were not counted
because they had MAC-layer errors.
Note that if the dsmonHostTable is inactive because no
appropriate protocols are enabled in the protocol directory,
this value SHOULD be 0.
Note that, unlike the dropEvents counter, this number is the
exact number of frames dropped."
::= { dsmonHostCtlEntry 7 }
dsmonHostCtlInserts OBJECT-TYPE
SYNTAX Counter32
UNITS "table entries"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times a dsmonHost entry has been inserted
into the dsmonHost table. If an entry is inserted, then
deleted, and then inserted, this counter will be incremented
by 2.
To allow for efficient implementation strategies, agents MAY
delay updating this object for short periods of time. For
example, an implementation strategy may allow internal data
structures to differ from those visible via SNMP for short
periods of time. This counter may reflect the internal data
structures for those short periods of time.
Note that the table size can be determined by subtracting
dsmonHostCtlDeletes from dsmonHostCtlInserts."
::= { dsmonHostCtlEntry 8 }
dsmonHostCtlDeletes OBJECT-TYPE
SYNTAX Counter32
UNITS "table entries"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times a dsmonHost entry has been deleted from
the dsmonHost table (for any reason). If an entry is
deleted, then inserted, and then deleted, this counter will
be incremented by 2.
To allow for efficient implementation strategies, agents MAY
delay updating this object for short periods of time. For
example, an implementation strategy may allow internal data
structures to differ from those visible via SNMP for short
periods of time. This counter may reflect the internal data
structures for those short periods of time.
Note that the table size can be determined by subtracting
dsmonHostCtlDeletes from dsmonHostCtlInserts."
::= { dsmonHostCtlEntry 9 }
dsmonHostCtlCreateTime OBJECT-TYPE
SYNTAX LastCreateTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime when this control entry was last
activated. This can be used by the management station to
detect if the table has been deleted and recreated between
polls."
::= { dsmonHostCtlEntry 10 }
dsmonHostCtlOwner OBJECT-TYPE
SYNTAX OwnerString
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The entity that configured this entry and is therefore
using the resources assigned to it."
::= { dsmonHostCtlEntry 11 }
dsmonHostCtlStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this dsmonHostCtlEntry.
An entry MUST NOT exist in the active state unless all
objects in the entry have an appropriate value.
If this object is not equal to active(1), all associated
entries in the dsmonHostTable shall be deleted."
::= { dsmonHostCtlEntry 12 }
--
-- NL Host Statistics Table
--
dsmonHostTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonHostEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A collection of statistics for particular network protocols
which contain a DS field, and that has been discovered on a
particular dataSource.
The probe will add to this table all appropriate network
protocols, for each network address seen as the source or
destination address in all packets with no MAC errors, and
will increment octet and packet counts in the table for all
packets with no MAC errors.
If the dsmonAggControlLocked object is equal to 'false',
then all entries in this table will be deleted, and the
agent will not process packets on behalf of any
dsmonHostCtlEntry."
::= { dsmonHostObjects 2 }
dsmonHostEntry OBJECT-TYPE
SYNTAX DsmonHostEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of information on Differentiated Services DSCP
usage, containing packet and octet counters for each counter
aggregation group index configured for collection per host
address, as identified in the dsmonAggProfileTable.
The dsmonHostCtlIndex value in the index identifies the
dsmonHostCtlEntry on whose behalf this entry was created.
The protocolDirLocalIndex value in the index identifies the
specific network layer protocol encapsulation associated
with each entry, and the network protocol type of the
dsmonHostAddress object. It MUST identify a
protocolDirEntry which contains a DS field (e.g., IPv4 or
IPv6). Note that if a protocol encapsulation with multiple
network layers is specified, then associated entries in this
table refer to the innermost network protocol layer host
address.
The dsmonAggGroupIndex value in the index is determined by
examining the DSCP value in each monitored packet, and the
dsmonAggProfileTable entry configured for that value.
An example of the indexing of this entry is
dsmonHostOutPkts.1.27273.3.200.4.171.69.120.0"
INDEX { dsmonHostCtlIndex,
dsmonHostTimeMark,
dsmonAggGroupIndex,
protocolDirLocalIndex,
dsmonHostAddress }
::= { dsmonHostTable 1 }
DsmonHostEntry ::= SEQUENCE {
dsmonHostTimeMark TimeFilter,
dsmonHostAddress OCTET STRING,
dsmonHostInPkts ZeroBasedCounter32,
dsmonHostInOctets ZeroBasedCounter32,
dsmonHostInOvflPkts ZeroBasedCounter32,
dsmonHostInOvflOctets ZeroBasedCounter32,
dsmonHostInHCPkts ZeroBasedCounter64,
dsmonHostInHCOctets ZeroBasedCounter64,
dsmonHostOutPkts ZeroBasedCounter32,
dsmonHostOutOctets ZeroBasedCounter32,
dsmonHostOutOvflPkts ZeroBasedCounter32,
dsmonHostOutOvflOctets ZeroBasedCounter32,
dsmonHostOutHCPkts ZeroBasedCounter64,
dsmonHostOutHCOctets ZeroBasedCounter64,
dsmonHostCreateTime LastCreateTime
}
dsmonHostTimeMark OBJECT-TYPE
SYNTAX TimeFilter
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Time Filter index for this table. This object may be
used by a management station to retrieve only rows which
have been created or modified since a particular time. Note
that the current value for a row are always returned and the
TimeFilter is not a historical data archiving mechanism.
Refer to RFC 2021 [RFC2021] for a detailed description of
TimeFilter operation."
::= { dsmonHostEntry 1 }
dsmonHostAddress OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..110))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The network address for this dsmonHostEntry.
This object is encoded according to the protocol type
indicated by the protocolDirLocalIndex value in the index.
In addition, this object may have some 'rightmost' bits
cleared to zero for counting purposes, as indicated by the
associated dsmonHostCtlIPv4PrefixLen or
dsmonHostCtlIPv6PrefixLen objects."
::= { dsmonHostEntry 2 }
dsmonHostInPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of packets without errors, using one of the DSCP
values in the indicated counter aggregation group, and
transmitted to this address, since this entry was added to
the dsmonHostTable. Note that this is the number of link-
layer packets, so if a single network-layer packet is
fragmented into several link-layer frames, this counter is
incremented several times."
::= { dsmonHostEntry 3 }
dsmonHostInOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets in all packets, transmitted to this
address and using one of the DSCP values in the indicated
counter aggregation group, since this entry was added to the
dsmonHostTable (excluding framing bits but including FCS
octets), excluding those octets in packets that contained
errors.
Note this doesn't count just those octets in the particular
protocol frames, but includes the entire packet that
contained the protocol."
::= { dsmonHostEntry 4 }
dsmonHostInOvflPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of times the associated dsmonHostInPkts counter
has overflowed. Note that this object will only be
instantiated if the associated dsmonHostInHCPkts object is
also instantiated for a particular dataSource."
::= { dsmonHostEntry 5 }
dsmonHostInOvflOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of times the associated dsmonHostInOctets
counter has overflowed. Note that this object will only be
instantiated if the associated dsmonHostInHCOctets object is
also instantiated for a particular dataSource."
::= { dsmonHostEntry 6 }
dsmonHostInHCPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter64
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 64-bit version of the dsmonHostInPkts object.
Note that this object will only be instantiated if the RMON
agent supports High Capacity monitoring for a particular
dataSource."
::= { dsmonHostEntry 7 }
dsmonHostInHCOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter64
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 64-bit version of the dsmonHostInOctets object.
Note that this object will only be instantiated if the RMON
agent supports High Capacity monitoring for a particular
dataSource."
::= { dsmonHostEntry 8 }
dsmonHostOutPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of packets without errors, using one of the DSCP
values in the indicated counter aggregation group, and
transmitted by this address, since this entry was added to
the dsmonHostTable. Note that this is the number of link-
layer packets, so if a single network-layer packet is
fragmented into several link-layer frames, this counter is
incremented several times."
::= { dsmonHostEntry 9 }
dsmonHostOutOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets, transmitted by this address and using
one of the DSCP values in the identified counter aggregation
group, since this entry was added to the dsmonHostTable
(excluding framing bits but including FCS octets), excluding
those octets in packets that contained errors.
Note this doesn't count just those octets in the particular
protocol frames, but includes the entire packet that
contained the protocol."
::= { dsmonHostEntry 10 }
dsmonHostOutOvflPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of times the associated dsmonHostOutPkts counter
has overflowed. Note that this object will only be
instantiated if the associated dsmonHostOutHCPkts object is
also instantiated for a particular dataSource."
::= { dsmonHostEntry 11 }
dsmonHostOutOvflOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of times the associated dsmonHostOutOctets
counter has overflowed. Note that this object will only be
instantiated if the associated dsmonHostOutHCOctets object
is also instantiated for a particular dataSource."
::= { dsmonHostEntry 12 }
dsmonHostOutHCPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter64
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 64-bit version of the dsmonHostOutPkts object.
Note that this object will only be instantiated if the RMON
agent supports High Capacity monitoring for a particular
dataSource."
::= { dsmonHostEntry 13 }
dsmonHostOutHCOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter64
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 64-bit version of the dsmonHostOutOctets object.
Note that this object will only be instantiated if the RMON
agent supports High Capacity monitoring for a particular
dataSource."
::= { dsmonHostEntry 14 }
dsmonHostCreateTime OBJECT-TYPE
SYNTAX LastCreateTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime when this dsmonHost entry was last
instantiated by the agent. This can be used by the
management station to ensure that the entry has not been
deleted and recreated between polls."
::= { dsmonHostEntry 15 }
--
-- Per-Protocol Per-Host NL Statistics TopN Control Table
--
dsmonHostTopNCtlTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonHostTopNCtlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A set of parameters that control the creation of a report
of the top N dsmonHost entries according to a selected
metric.
Note that an agent MAY choose to limit the actual number of
entries which may be created in this table. In this case,
the agent SHOULD return an error-status of
'resourceUnavailable(13)', as per section 4.2.5 of the
'Protocol Operations for SNMPv2' specification [RFC1905]."
::= { dsmonHostObjects 3 }
dsmonHostTopNCtlEntry OBJECT-TYPE
SYNTAX DsmonHostTopNCtlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in the dsmonHostTopNCtlTable.
Entries are created and deleted from this table by
management action only, using the dsmonHostTopNCtlStatus
RowStatus object.
The agent SHOULD support non-volatile configuration of this
table, and upon system initialization, the table SHOULD be
initialized with the saved values.
Activation of a control row in this table will cause an
associated dsmonHostTopNTable to be created and maintained
by the agent."
INDEX { dsmonHostTopNCtlIndex }
::= { dsmonHostTopNCtlTable 1 }
DsmonHostTopNCtlEntry ::= SEQUENCE {
dsmonHostTopNCtlIndex Integer32,
dsmonHostTopNCtlHostIndex Integer32,
dsmonHostTopNCtlRateBase INTEGER,
dsmonHostTopNCtlTimeRemaining Integer32,
dsmonHostTopNCtlGeneratedReports Counter32,
dsmonHostTopNCtlDuration Integer32,
dsmonHostTopNCtlRequestedSize Integer32,
dsmonHostTopNCtlGrantedSize Integer32,
dsmonHostTopNCtlStartTime TimeStamp,
dsmonHostTopNCtlOwner OwnerString,
dsmonHostTopNCtlStatus RowStatus
}
dsmonHostTopNCtlIndex OBJECT-TYPE
SYNTAX Integer32 (1..65535)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An index that uniquely identifies an entry in the
dsmonHostTopNCtlTable. Each such entry defines one Top N
report prepared for one RMON dataSource."
::= { dsmonHostTopNCtlEntry 1 }
dsmonHostTopNCtlHostIndex OBJECT-TYPE
SYNTAX Integer32 (1..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The dsmonHostTable for which a top N report will be
prepared on behalf of this entry. The dsmonHostTable is
identified by the value of the dsmonHostCtlIndex for that
table - that value is used here to identify the particular
table.
This object MUST NOT be modified if the associated
dsmonHostTopNCtlStatus object is equal to active(1)."
::= { dsmonHostTopNCtlEntry 2 }
dsmonHostTopNCtlRateBase OBJECT-TYPE
SYNTAX INTEGER {
dsmonHostTopNInPkts(1),
dsmonHostTopNInOctets(2),
dsmonHostTopNOutPkts(3),
dsmonHostTopNOutOctets(4),
dsmonHostTopNTotalPkts(5),
dsmonHostTopNTotalOctets(6),
dsmonHostTopNInHCPkts(7),
dsmonHostTopNInHCOctets(8),
dsmonHostTopNOutHCPkts(9),
dsmonHostTopNOutHCOctets(10),
dsmonHostTopNTotalHCPkts(11),
dsmonHostTopNTotalHCOctets(12)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The variable(s) for each dsmonHost that the
dsmonHostTopNRate and dsmonHostTopNHCRate variables are
based upon. Each dsmonHostTopN report generated on behalf
of this control entry will be ranked in descending order,
based on the associated dsmonHostTable counter(s),
identified by this object.
The following table identifies the dsmonHostTable counters
associated with each enumeration:
Enumeration RateBase MIB Objects
----------- --------------------
dsmonHostTopNInPkts dsmonHostInPkts
dsmonHostTopNInOctets dsmonHostInOctets
dsmonHostTopNOutPkts dsmonHostOutPkts
dsmonHostTopNOutOctets dsmonHostOutOctets
dsmonHostTopNTotalPkts dsmonHostInPkts +
dsmonHostOutPkts
dsmonHostTopNTotalOctets dsmonHostInOctets +
dsmonHostOutOctets
dsmonHostTopNInHCPkts dsmonHostInHCPkts
dsmonHostTopNInHCOctets dsmonHostInHCOctets
dsmonHostTopNOutHCPkts dsmonHostOutHCPkts
dsmonHostTopNOutHCOctets dsmonHostOutHCPkts
dsmonHostTopNTotalHCPkts dsmonHostInHCPkts +
dsmonHostOutHCPkts
dsmonHostTopNTotalHCOctets dsmonHostInHCOctets +
dsmonHostOutHCOctets
The following enumerations are only available if the agent
supports High Capacity monitoring:
dsmonHostTopNInHCPkts
dsmonHostTopNInHCOctets
dsmonHostTopNOutHCPkts
dsmonHostTopNOutHCOctets
dsmonHostTopNTotalHCPkts
dsmonHostTopNTotalHCOctets
It is an implementation-specific matter whether an agent can
detect an overflow condition resulting from the addition of
two counter delta values for the following enumerations:
dsmonHostTopNTotalPkts
dsmonHostTopNTotalOctets
dsmonHostTopNTotalHCPkts
dsmonHostTopNTotalHCOctets
In the event such an overflow condition can be detected by
the agent, the associated dsmonHostTopNRate,
dsmonHostTopNRateOvfl, and/or dsmonHostTopNHCRate objects
should be set to their maximum value.
This object MUST NOT be modified if the associated
dsmonHostTopNCtlStatus object is equal to active(1)."
::= { dsmonHostTopNCtlEntry 3 }
dsmonHostTopNCtlTimeRemaining OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The number of seconds left in the report currently being
collected. When this object is modified by the management
station, a new collection is started, possibly aborting a
currently running report. The new value is used as the
requested duration of this report, and is immediately loaded
into the associated dsmonHostTopNCtlDuration object.
When the report finishes, the probe will automatically start
another collection with the same initial value of
dsmonHostTopNCtlTimeRemaining. Thus the management station
may simply read the resulting reports repeatedly, checking
the startTime and duration each time to ensure that a report
was not missed or that the report parameters were not
changed.
While the value of this object is non-zero, it decrements by
one per second until it reaches zero. At the time that this
object decrements to zero, the report is made accessible in
the dsmonHostTopNTable, overwriting any report that may be
there.
When this object is modified by the management station, any
associated entries in the dsmonHostTopNTable shall be
deleted."
DEFVAL { 1800 }
::= { dsmonHostTopNCtlEntry 4 }
dsmonHostTopNCtlGeneratedReports OBJECT-TYPE
SYNTAX Counter32
UNITS "reports"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of reports that have been generated by this
entry."
::= { dsmonHostTopNCtlEntry 5 }
dsmonHostTopNCtlDuration OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of seconds that this report has collected during
the last sampling interval.
When the associated dsmonHostTopNCtlTimeRemaining object is
set, this object shall be set by the probe to the same value
and shall not be modified until the next time the
dsmonHostTopNCtlTimeRemaining is set.
This value shall be zero if no reports have been requested
for this dsmonHostTopNCtlEntry."
::= { dsmonHostTopNCtlEntry 6 }
dsmonHostTopNCtlRequestedSize OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
UNITS "table entries"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum number of dsmonHost entries requested for this
report.
When this object is created or modified, the probe SHOULD
set dsmonHostTopNCtlGrantedSize as closely to this object as
is possible for the particular probe implementation and
available resources."
DEFVAL { 150 }
::= { dsmonHostTopNCtlEntry 7 }
dsmonHostTopNCtlGrantedSize OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
UNITS "table entries"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum number of dsmonHost entries in this report.
When the associated dsmonHostTopNCtlRequestedSize object is
created or modified, the probe SHOULD set this object as
closely to the requested value as is possible for the
particular implementation and available resources. The
probe MUST NOT lower this value except as a result of a
set to the associated dsmonHostTopNCtlRequestedSize
object.
Protocol entries with the highest value of dsmonHostTopNRate
or dsmonHostTopNHCRate (depending on the value of the
associated dsmonHostTopNCtlRateBase object) shall be placed
in this table in decreasing order of this rate until there
is no more room or until there are no more dsmonHost
entries."
::= { dsmonHostTopNCtlEntry 8 }
dsmonHostTopNCtlStartTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime when this top N report was last
started. In other words, this is the time that the
associated dsmonHostTopNCtlTimeRemaining object was modified
to start the requested report or the time the report was
last automatically (re)started.
This object may be used by the management station to
determine if a report was missed or not."
::= { dsmonHostTopNCtlEntry 9 }
dsmonHostTopNCtlOwner OBJECT-TYPE
SYNTAX OwnerString
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The entity that configured this entry and is therefore
using the resources assigned to it."
::= { dsmonHostTopNCtlEntry 10 }
dsmonHostTopNCtlStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this dsmonHostTopNCtlEntry.
An entry MUST NOT exist in the active state unless all
objects in the entry have an appropriate value.
If this object is not equal to active(1), all associated
entries in the dsmonHostTopNTable shall be deleted by the
agent."
::= { dsmonHostTopNCtlEntry 11 }
--
-- dsmonHost TopN Table
--
dsmonHostTopNTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonHostTopNEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A set of statistics for those dsmonHost entries that have
counted the highest number of octets or packets.
If the dsmonAggControlLocked object is equal to 'false',
then all entries in this table SHALL be deleted, and the
agent will not process TopN reports on behalf of any
dsmonHostTopNCtlEntry.
When the dsmonAggControlLocked object is set to 'true', then
particular reports SHOULD be restarted from the beginning,
on behalf of all active rows in the dsmonHostTopNCtlTable.
Note that dsmonHost entries which did not increment at all
during the report interval SHOULD NOT be included in
dsmonHostTopN reports."
::= { dsmonHostObjects 4 }
dsmonHostTopNEntry OBJECT-TYPE
SYNTAX DsmonHostTopNEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in the dsmonHostTopNTable.
The dsmonHostTopNCtlIndex value in the index identifies the
dsmonHostTopNCtlEntry on whose behalf this entry was
created.
Entries in this table are ordered from 1 to 'N', where lower
numbers represent higher values of the rate base object,
over the report interval."
INDEX { dsmonHostTopNCtlIndex, dsmonHostTopNIndex }
::= { dsmonHostTopNTable 1 }
DsmonHostTopNEntry ::= SEQUENCE {
dsmonHostTopNIndex Integer32,
dsmonHostTopNPDLocalIndex Integer32,
dsmonHostTopNAddress OCTET STRING,
dsmonHostTopNAggGroup DsmonCounterAggGroupIndex,
dsmonHostTopNRate Gauge32,
dsmonHostTopNRateOvfl Gauge32,
dsmonHostTopNHCRate CounterBasedGauge64
}
dsmonHostTopNIndex OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An index that uniquely identifies an entry in the
dsmonHostTopNTable among those in the same report. This
index is between 1 and N, where N is the number of entries
in this report."
::= { dsmonHostTopNEntry 1 }
dsmonHostTopNPDLocalIndex OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The protocolDirLocalIndex value which identifies the
protocol associated with the dsmonHostTopNAddress object in
this entry.
If the protocolDirEntry associated with the
protocolDirLocalIndex with the same value as this object is
de-activated or deleted, then the agent MUST delete this
dsmonHostTopN entry."
::= { dsmonHostTopNEntry 2 }
dsmonHostTopNAddress OBJECT-TYPE
SYNTAX OCTET STRING
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The dsmonHostAddress value for the network host identified
in this entry. The associated dsmonHostTopNPDLocalIndex
object identifies the network protocol type and the encoding
rules for this object."
::= { dsmonHostTopNEntry 3 }
dsmonHostTopNAggGroup OBJECT-TYPE
SYNTAX DsmonCounterAggGroupIndex
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter aggregation group index value associated with
host identified in this entry. This object identifies the
dsmonAggGroupEntry with the same dsmonAggControlIndex value
as the associated dsmonHostCtlAggProfile object and the same
dsmonAggGroupIndex value as this object."
::= { dsmonHostTopNEntry 4 }
dsmonHostTopNRate OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The amount of change in the selected variable during this
sampling interval. The selected variable is this host's
instance of the object selected by dsmonHostTopNCtlRateBase.
If the associated dsmonHostTopNCtlRateBase indicates a High
Capacity monitoring enumeration, (e.g.
'dsmonHostTopNInHCPkts'), then this object will contain the
the least significant 32 bits of the associated
dsmonHostTopNHCRate object."
::= { dsmonHostTopNEntry 5 }
dsmonHostTopNRateOvfl OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The most significant 32 bits of the associated
dsmonHostTopNHCRate object.
If the associated dsmonHostTopNCtlRateBase is equal to any
of the High Capacity monitoring enumerations (e.g.
'dsmonHostTopNInHCPkts'), then this object will contain the
upper 32 bits of the associated dsmonHostTopNHCRate object.
If the associated dsmonHostTopNCtlRateBase is not equal to
any of High Capacity monitoring enumerations, then this
object will contain the value zero.
The agent MAY choose not to instantiate this object if High
Capacity monitoring is not supported."
::= { dsmonHostTopNEntry 6 }
dsmonHostTopNHCRate OBJECT-TYPE
SYNTAX CounterBasedGauge64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The amount of change in the selected variable during this
sampling interval. The selected variable is this host's
instance of the object selected by dsmonHostTopNCtlRateBase.
If the associated dsmonHostTopNCtlRateBase is not equal to
any of the High Capacity monitoring enumerations (e.g.,
'dsmonHostTopNInPkts'), then this object will contain the
value zero, and the associated dsmonHostTopNRate object will
contain the change in the selected variable during the
sampling interval.
The agent MAY choose not to instantiate this object if High
Capacity monitoring is not supported."
::= { dsmonHostTopNEntry 7 }
-- **************************************************************
-- * *
-- * P E R - C O N V E R S I O N C O L L E C T I O N S *
-- * *
-- **************************************************************
--
-- AL Matrix Statistics Control Table
--
dsmonMatrixCtlTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonMatrixCtlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Controls setup of per counter aggregation group, per host-
pair, application protocol distribution statistics.
Note that an agent MAY choose to limit the actual number of
entries which may be created in this table. In this case,
the agent SHOULD return an error-status of
'resourceUnavailable(13)', as per section 4.2.5 of the
'Protocol Operations for SNMPv2' specification [RFC1905]."
::= { dsmonMatrixObjects 1 }
dsmonMatrixCtlEntry OBJECT-TYPE
SYNTAX DsmonMatrixCtlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in the dsmonMatrixCtlTable.
Entries are created and deleted from this table by
management action only, using the dsmonMatrixCtlStatus
RowStatus object.
The agent SHOULD support non-volatile configuration of this
table, and upon system initialization, the table SHOULD be
initialized with the saved values.
Activation of a control row in this table will cause an
associated dsmonMatrixSDTable and dsmonMatrixDSTable to be
created and maintained by the agent."
INDEX { dsmonMatrixCtlIndex }
::= { dsmonMatrixCtlTable 1 }
DsmonMatrixCtlEntry ::= SEQUENCE {
dsmonMatrixCtlIndex Integer32,
dsmonMatrixCtlDataSource DataSource,
dsmonMatrixCtlAggProfile DsmonCounterAggProfileIndex,
dsmonMatrixCtlMaxDesiredEntries Integer32,
dsmonMatrixCtlDroppedFrames Counter32,
dsmonMatrixCtlInserts Counter32,
dsmonMatrixCtlDeletes Counter32,
dsmonMatrixCtlCreateTime LastCreateTime,
dsmonMatrixCtlOwner OwnerString,
dsmonMatrixCtlStatus RowStatus
}
dsmonMatrixCtlIndex OBJECT-TYPE
SYNTAX Integer32 (1..65535)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An arbitrary and unique index for this
dsmonMatrixCtlEntry."
::= { dsmonMatrixCtlEntry 1 }
dsmonMatrixCtlDataSource OBJECT-TYPE
SYNTAX DataSource
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The source of data for the associated dsmonMatrixSDTable
and dsmonMatrixDSTable.
Note that only packets that contain a network protocol
encapsulation which contains a DS field [RFC2474] will be
counted in this table.
This object MUST NOT be modified if the associated
dsmonMatrixCtlStatus object is equal to active(1)."
::= { dsmonMatrixCtlEntry 2 }
dsmonMatrixCtlAggProfile OBJECT-TYPE
SYNTAX DsmonCounterAggProfileIndex
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The dsmonAggControlIndex value identifying the counter
aggregation profile which should be used on behalf of this
dsmonMatrixCtlEntry.
The associated dsmonAggControlEntry and
dsmonAggProfileEntries, identified by the same
dsmonAggControlIndex index value, MUST be active in order
for this entry to remain active. It is possible for the
counter aggregation configuration to change from a valid to
invalid state for this dsmonMatrix collection. In this
case, the associated dsmonMatrixCtlStatus object will be
changed to the 'notReady' state, and data collection will
not occur on behalf of this control entry.
Note that an agent MAY choose to limit the actual number of
counter aggregation profiles which may be applied to a
particular data source.
This object MUST NOT be modified if the associated
dsmonMatrixCtlStatus object is equal to active(1)."
::= { dsmonMatrixCtlEntry 3 }
dsmonMatrixCtlMaxDesiredEntries OBJECT-TYPE
SYNTAX Integer32 (-1 | 1..2147483647)
UNITS "table entries"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum number of entries that are desired in the
dsmonMatrix tables on behalf of this control entry. The
probe will not create more than this number of associated
entries in these tables, but may choose to create fewer
entries in this table for any reason including the lack of
resources.
If this value is set to -1, the probe may create any number
of entries in this table.
This object MUST NOT be modified if the associated
dsmonMatrixCtlStatus object is equal to active(1)."
::= { dsmonMatrixCtlEntry 4 }
dsmonMatrixCtlDroppedFrames OBJECT-TYPE
SYNTAX Counter32
UNITS "frames"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of frames which were received by the probe
and therefore not accounted for in the *StatsDropEvents, but
for which the probe chose not to count for the associated
dsmonMatrixSD and dsmonMatrixDS entries for whatever reason.
Most often, this event occurs when the probe is out of some
resources and decides to shed load from this collection.
This count does not include packets that were not counted
because they had MAC-layer errors.
Note that if the dsmonMatrix tables are inactive because no
appropriate protocols are enabled in the protocol directory,
this value SHOULD be 0.
Note that, unlike the dropEvents counter, this number is the
exact number of frames dropped."
::= { dsmonMatrixCtlEntry 5 }
dsmonMatrixCtlInserts OBJECT-TYPE
SYNTAX Counter32
UNITS "table entries"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times a dsmonMatrix entry has been inserted
into the dsmonMatrix tables. If an entry is inserted, then
deleted, and then inserted, this counter will be incremented
by 2. The addition of a conversation into both the
dsmonMatrixSDTable and dsmonMatrixDSTable shall be counted
as two insertions (even though every addition into one table
must be accompanied by an insertion into the other).
To allow for efficient implementation strategies, agents may
delay updating this object for short periods of time. For
example, an implementation strategy may allow internal data
structures to differ from those visible via SNMP for short
periods of time. This counter may reflect the internal data
structures for those short periods of time. Note that the
sum of the dsmonMatrixSDTable and dsmonMatrixDSTable sizes
can be determined by subtracting dsmonMatrixCtlDeletes from
dsmonMatrixCtlInserts."
::= { dsmonMatrixCtlEntry 6 }
dsmonMatrixCtlDeletes OBJECT-TYPE
SYNTAX Counter32
UNITS "table entries"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times a dsmonMatrix entry has been deleted
from the dsmonMatrix tables (for any reason). If an entry
is deleted, then inserted, and then deleted, this counter
will be incremented by 2. The deletion of a conversation
from both the dsmonMatrixSDTable and dsmonMatrixDSTable
shall be counted as two deletions (even though every
deletion from one table must be accompanied by a deletion
from the other).
To allow for efficient implementation strategies, agents MAY
delay updating this object for short periods of time. For
example, an implementation strategy may allow internal data
structures to differ from those visible via SNMP for short
periods of time. This counter may reflect the internal data
structures for those short periods of time.
Note that the sum of the dsmonMatrixSDTable and
dsmonMatrixDSTable sizes can be determined by subtracting
dsmonMatrixCtlDeletes from dsmonMatrixCtlInserts."
::= { dsmonMatrixCtlEntry 7 }
dsmonMatrixCtlCreateTime OBJECT-TYPE
SYNTAX LastCreateTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime when this control entry was last
activated. This can be used by the management station to
detect if the table has been deleted and recreated between
polls."
::= { dsmonMatrixCtlEntry 8 }
dsmonMatrixCtlOwner OBJECT-TYPE
SYNTAX OwnerString
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The entity that configured this entry and is therefore
using the resources assigned to it."
::= { dsmonMatrixCtlEntry 9 }
dsmonMatrixCtlStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this dsmonMatrixCtlEntry.
An entry MUST NOT exist in the active state unless all
objects in the entry have an appropriate value.
If this object is not equal to active(1), all associated
entries in the dsmonMatrixSDTable and dsmonMatrixDSTable
shall be deleted."
::= { dsmonMatrixCtlEntry 10 }
--
-- AL Matrix SD Statistics Table
--
dsmonMatrixSDTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonMatrixSDEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of application traffic matrix entries which collect
statistics for conversations of a particular application
protocol between two network-level addresses. This table is
indexed first by the source address and then by the
destination address to make it convenient to collect all
statistics from a particular address.
The probe will add to this table all pairs of addresses for
all protocols seen in all packets with no MAC errors, and
will increment octet and packet counts in the table for all
packets with no MAC errors."
::= { dsmonMatrixObjects 2 }
dsmonMatrixSDEntry OBJECT-TYPE
SYNTAX DsmonMatrixSDEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in the dsmonMatrixSDTable.
The dsmonMatrixCtlIndex value in the index identifies the
dsmonMatrixCtlEntry on whose behalf this entry was created.
The dsmonAggGroupIndex value in the index is determined by
examining the DSCP value in each monitored packet, and the
dsmonAggProfileTable entry configured for that value."
INDEX { dsmonMatrixCtlIndex,
dsmonMatrixTimeMark,
dsmonAggGroupIndex,
dsmonMatrixNLIndex,
dsmonMatrixSourceAddress,
dsmonMatrixDestAddress,
dsmonMatrixALIndex
}
::= { dsmonMatrixSDTable 1 }
DsmonMatrixSDEntry ::= SEQUENCE {
dsmonMatrixTimeMark TimeFilter,
dsmonMatrixNLIndex Integer32,
dsmonMatrixSourceAddress OCTET STRING,
dsmonMatrixDestAddress OCTET STRING,
dsmonMatrixALIndex Integer32,
dsmonMatrixSDPkts ZeroBasedCounter32,
dsmonMatrixSDOvflPkts ZeroBasedCounter32,
dsmonMatrixSDHCPkts ZeroBasedCounter64,
dsmonMatrixSDOctets ZeroBasedCounter32,
dsmonMatrixSDOvflOctets ZeroBasedCounter32,
dsmonMatrixSDHCOctets ZeroBasedCounter64,
dsmonMatrixSDCreateTime LastCreateTime
}
dsmonMatrixTimeMark OBJECT-TYPE
SYNTAX TimeFilter
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Time Filter index for this table. This object may be
used by a management station to retrieve only rows which
have been created or modified since a particular time. Note
that the current value for a row are always returned and the
TimeFilter is not a historical data archiving mechanism.
Refer to RFC 2021 [RFC2021] for a detailed description of
TimeFilter operation."
::= { dsmonMatrixSDEntry 1 }
dsmonMatrixNLIndex OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The protocolDirLocalIndex value of a protocolDirEntry
representing the specific network layer protocol
encapsulation associated with each entry, and the network
protocol type of the dsmonMatrixSourceAddress and
dsmonMatrixDestAddress objects."
::= { dsmonMatrixSDEntry 2 }
dsmonMatrixSourceAddress OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..54))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The network source address for this dsmonMatrix entry.
This is represented as an octet string with specific
semantics and length as identified by the dsmonMatrixNLIndex
component of the index.
For example, if the dsmonMatrixNLIndex indicates an
encapsulation of IPv4, this object is encoded as a length
octet of 4, followed by the 4 octets of the IPv4 address, in
network byte order."
::= { dsmonMatrixSDEntry 3 }
dsmonMatrixDestAddress OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..54))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The network destination address for this dsmonMatrix entry.
This is represented as an octet string with specific
semantics and length as identified by the dsmonMatrixNLIndex
component of the index.
For example, if the dsmonMatrixNLIndex indicates an
encapsulation of IPv4, this object is encoded as a length
octet of 4, followed by the 4 octets of the IPv4 address, in
network byte order."
::= { dsmonMatrixSDEntry 4 }
dsmonMatrixALIndex OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The protocolDirLocalIndex value of the protocolDirEntry
representing the specific application layer protocol
associated with each entry.
It MUST identify an protocolDirEntry which is a direct or
indirect descendant of the protocolDirEntry identified by
the associated dsmonMatrixNLIndex object."
::= { dsmonMatrixSDEntry 5 }
dsmonMatrixSDPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of packets of this protocol type (indicated by
the associated dsmonMatrixALIndex object) without errors
transmitted from the source address to the destination
address since this entry was added to the
dsmonMatrixSDTable. Note that this is the number of link-
layer packets, so if a single network-layer packet is
fragmented into several link-layer frames, this counter is
incremented several times."
::= { dsmonMatrixSDEntry 6 }
dsmonMatrixSDOvflPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of times the associated dsmonMatrixSDPkts
counter has overflowed, since this entry was added to the
dsmonMatrixSDTable."
::= { dsmonMatrixSDEntry 7 }
dsmonMatrixSDHCPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter64
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 64-bit version of the dsmonMatrixSDPkts object.
Note that this object will only be instantiated if the RMON
agent supports High Capacity monitoring for a particular
dataSource."
::= { dsmonMatrixSDEntry 8 }
dsmonMatrixSDOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets in packets of this protocol type
transmitted from the source address to the destination
address since this entry was added to the dsmonMatrixSDTable
(excluding framing bits but including FCS octets), excluding
those octets in packets that contained errors.
Note this doesn't count just those octets in the particular
protocol frames, but includes the entire packet that
contained the protocol."
::= { dsmonMatrixSDEntry 9 }
dsmonMatrixSDOvflOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of times the associated dsmonMatrixSDOctets
counter has overflowed, since this entry was added to the
dsmonMatrixSDTable."
::= { dsmonMatrixSDEntry 10 }
dsmonMatrixSDHCOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter64
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 64-bit version of the dsmonMatrixSDPkts object.
Note that this object will only be instantiated if the RMON
agent supports High Capacity monitoring for a particular
dataSource."
::= { dsmonMatrixSDEntry 11 }
dsmonMatrixSDCreateTime OBJECT-TYPE
SYNTAX LastCreateTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime when this entry was last activated.
This can be used by the management station to ensure that
the entry has not been deleted and recreated between polls."
::= { dsmonMatrixSDEntry 12 }
--
-- AL Matrix DS Statistics Table
--
dsmonMatrixDSTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonMatrixDSEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of application traffic matrix entries which collect
statistics for conversations of a particular application
protocol between two network-level addresses. This table is
indexed first by the destination address and then by the
source address to make it convenient to collect all
statistics from a particular address.
The probe will add to this table all pairs of addresses for
all protocols seen in all packets with no MAC errors, and
will increment octet and packet counts in the table for all
packets with no MAC errors."
::= { dsmonMatrixObjects 3 }
dsmonMatrixDSEntry OBJECT-TYPE
SYNTAX DsmonMatrixDSEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in the dsmonMatrixDSTable. Note that this
table is conceptually a re-ordered version of the
dsmonMatrixSDTable. Therefore, all of the index values from
that table are used by reference, and their semantics are
exactly as described in the dsmonMatrixSDTable.
The dsmonMatrixCtlIndex value in the index identifies the
dsmonMatrixCtlEntry on whose behalf this entry was created.
The dsmonMatrixTimeMark value in the index identifies the
Time Filter index for this table.
The dsmonAggGroupIndex value in the index is determined by
examining the DSCP value in each monitored packet, and the
dsmonAggProfileTable entry configured for that value.
The dsmonMatrixNLIndex value in the index identifies the
protocolDirLocalIndex value of a protocolDirEntry
representing the specific network layer protocol
encapsulation associated with each entry, and the network
protocol type of the dsmonMatrixSourceAddress and
dsmonMatrixDestAddress objects.
The dsmonMatrixDestAddress value in the index identifies the
network destination address for this dsmonMatrix entry.
The dsmonMatrixSourceAddress value in the index identifies
the network source address for this dsmonMatrix entry.
The dsmonMatrixALIndex value in the index identifies the
protocolDirLocalIndex value of the protocolDirEntry
representing the specific application layer protocol
associated with each entry."
INDEX { dsmonMatrixCtlIndex,
dsmonMatrixTimeMark,
dsmonAggGroupIndex,
dsmonMatrixNLIndex,
dsmonMatrixDestAddress,
dsmonMatrixSourceAddress,
dsmonMatrixALIndex
}
::= { dsmonMatrixDSTable 1 }
DsmonMatrixDSEntry ::= SEQUENCE {
dsmonMatrixDSPkts ZeroBasedCounter32,
dsmonMatrixDSOvflPkts ZeroBasedCounter32,
dsmonMatrixDSHCPkts ZeroBasedCounter64,
dsmonMatrixDSOctets ZeroBasedCounter32,
dsmonMatrixDSOvflOctets ZeroBasedCounter32,
dsmonMatrixDSHCOctets ZeroBasedCounter64,
dsmonMatrixDSCreateTime LastCreateTime
}
dsmonMatrixDSPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of packets of this protocol type (indicated by
the associated dsmonMatrixALIndex object) without errors
transmitted from the source address to the destination
address since this entry was added to the
dsmonMatrixDSTable. Note that this is the number of link-
layer packets, so if a single network-layer packet is
fragmented into several link-layer frames, this counter is
incremented several times."
::= { dsmonMatrixDSEntry 1 }
dsmonMatrixDSOvflPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of times the associated dsmonMatrixDSPkts
counter has overflowed, since this entry was added to the
dsmonMatrixDSTable."
::= { dsmonMatrixDSEntry 2 }
dsmonMatrixDSHCPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter64
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 64-bit version of the dsmonMatrixDSPkts object.
Note that this object will only be instantiated if the RMON
agent supports High Capacity monitoring for a particular
dataSource."
::= { dsmonMatrixDSEntry 3 }
dsmonMatrixDSOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets in packets of this protocol type
transmitted from the source address to the destination
address since this entry was added to the dsmonMatrixDSTable
(excluding framing bits but including FCS octets), excluding
those octets in packets that contained errors.
Note this doesn't count just those octets in the particular
protocol frames, but includes the entire packet that
contained the protocol."
::= { dsmonMatrixDSEntry 4 }
dsmonMatrixDSOvflOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of times the associated dsmonMatrixDSOctets
counter has overflowed, since this entry was added to the
dsmonMatrixDSTable."
::= { dsmonMatrixDSEntry 5 }
dsmonMatrixDSHCOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter64
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 64-bit version of the dsmonMatrixDSPkts object.
Note that this object will only be instantiated if the RMON
agent supports High Capacity monitoring for a particular
dataSource."
::= { dsmonMatrixDSEntry 6 }
dsmonMatrixDSCreateTime OBJECT-TYPE
SYNTAX LastCreateTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime when this entry was last activated.
This can be used by the management station to ensure that
the entry has not been deleted and recreated between polls."
::= { dsmonMatrixDSEntry 7 }
--
-- Per-Protocol Per-Matrix Statistics TopN Control Table
--
dsmonMatrixTopNCtlTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonMatrixTopNCtlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A set of parameters that control the creation of a report
of the top N dsmonMatrix entries according to a selected
metric.
Note that an agent MAY choose to limit the actual number of
entries which may be created in this table. In this case,
the agent SHOULD return an error-status of
'resourceUnavailable(13)', as per section 4.2.5 of the
'Protocol Operations for SNMPv2' specification [RFC1905]."
::= { dsmonMatrixObjects 4 }
dsmonMatrixTopNCtlEntry OBJECT-TYPE
SYNTAX DsmonMatrixTopNCtlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in the dsmonMatrixTopNCtlTable.
Entries are created and deleted from this table by
management action only, using the dsmonMatrixTopNCtlStatus
RowStatus object.
The agent SHOULD support non-volatile configuration of this
table, and upon system initialization, the table SHOULD be
initialized with the saved values.
Activation of a control row in this table will cause an
associated dsmonMatrixTopNTable to be created and maintained
by the agent."
INDEX { dsmonMatrixTopNCtlIndex }
::= { dsmonMatrixTopNCtlTable 1 }
DsmonMatrixTopNCtlEntry ::= SEQUENCE {
dsmonMatrixTopNCtlIndex Integer32,
dsmonMatrixTopNCtlMatrixIndex Integer32,
dsmonMatrixTopNCtlRateBase INTEGER,
dsmonMatrixTopNCtlTimeRemaining Integer32,
dsmonMatrixTopNCtlGeneratedRpts Counter32,
dsmonMatrixTopNCtlDuration Integer32,
dsmonMatrixTopNCtlRequestedSize Integer32,
dsmonMatrixTopNCtlGrantedSize Integer32,
dsmonMatrixTopNCtlStartTime TimeStamp,
dsmonMatrixTopNCtlOwner OwnerString,
dsmonMatrixTopNCtlStatus RowStatus
}
dsmonMatrixTopNCtlIndex OBJECT-TYPE
SYNTAX Integer32 (1..65535)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An index that uniquely identifies an entry in the
dsmonMatrixTopNCtlTable. Each such entry defines one Top N
report prepared for one RMON dataSource."
::= { dsmonMatrixTopNCtlEntry 1 }
dsmonMatrixTopNCtlMatrixIndex OBJECT-TYPE
SYNTAX Integer32 (1..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The dsmonMatrixSDTable for which a top N report will be
prepared on behalf of this entry. The dsmonMatrixSDTable is
identified by the same value of the dsmonMatrixCtlIndex
object.
This object MUST NOT be modified if the associated
dsmonMatrixTopNCtlStatus object is equal to active(1)."
::= { dsmonMatrixTopNCtlEntry 2 }
dsmonMatrixTopNCtlRateBase OBJECT-TYPE
SYNTAX INTEGER {
dsmonMatrixTopNPkts(1),
dsmonMatrixTopNOctets(2),
dsmonMatrixTopNHCPkts(3),
dsmonMatrixTopNHCOctets(4)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The variable for each dsmonMatrixSD entry that the
dsmonMatrixTopNRate and dsmonMatrixTopNHCRate variables are
based upon. Each dsmonMatrixTopN report generated on behalf
of this control entry will be ranked in descending order,
based on the associated dsmonMatrixSDTable counter,
identified by this object.
The following table identifies the dsmonMatrixSDTable
counters associated with each enumeration:
Enumeration RateBase MIB Objects
----------- --------------------
dsmonMatrixTopNPkts dsmonMatrixSDPkts
dsmonMatrixTopNOctets dsmonMatrixSDOctets
dsmonMatrixTopNHCPkts dsmonMatrixSDHCPkts
dsmonMatrixTopNHCOctets dsmonMatrixSDHCOctets
The following enumerations are only available if the agent
supports High Capacity monitoring:
dsmonMatrixTopNHCPkts
dsmonMatrixTopNHCOctets
This object MUST NOT be modified if the associated
dsmonMatrixTopNCtlStatus object is equal to active(1)."
::= { dsmonMatrixTopNCtlEntry 3 }
dsmonMatrixTopNCtlTimeRemaining OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The number of seconds left in the report currently being
collected. When this object is modified by the management
station, a new collection is started, possibly aborting a
currently running report. The new value is used as the
requested duration of this report, and is immediately loaded
into the associated dsmonMatrixTopNCtlDuration object.
When the report finishes, the probe will automatically start
another collection with the same initial value of
dsmonMatrixTopNCtlTimeRemaining. Thus the management
station may simply read the resulting reports repeatedly,
checking the startTime and duration each time to ensure that
a report was not missed or that the report parameters were
not changed.
While the value of this object is non-zero, it decrements by
one per second until it reaches zero. At the time that this
object decrements to zero, the report is made accessible in
the dsmonMatrixTopNTable, overwriting any report that may be
there.
When this object is modified by the management station, any
associated entries in the dsmonMatrixTopNTable shall be
deleted."
DEFVAL { 1800 }
::= { dsmonMatrixTopNCtlEntry 4 }
dsmonMatrixTopNCtlGeneratedRpts OBJECT-TYPE
SYNTAX Counter32
UNITS "reports"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of reports that have been generated by this
entry."
::= { dsmonMatrixTopNCtlEntry 5 }
dsmonMatrixTopNCtlDuration OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of seconds that this report has collected during
the last sampling interval.
When the associated dsmonMatrixTopNCtlTimeRemaining object
is set, this object shall be set by the probe to the same
value and shall not be modified until the next time the
dsmonMatrixTopNCtlTimeRemaining is set.
This value shall be zero if no reports have been requested
for this dsmonMatrixTopNCtlEntry."
::= { dsmonMatrixTopNCtlEntry 6 }
dsmonMatrixTopNCtlRequestedSize OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
UNITS "table entries"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum number of dsmonMatrix entries requested for
this report.
When this object is created or modified, the probe SHOULD
set dsmonMatrixTopNCtlGrantedSize as closely to this object
as is possible for the particular probe implementation and
available resources."
DEFVAL { 150 }
::= { dsmonMatrixTopNCtlEntry 7 }
dsmonMatrixTopNCtlGrantedSize OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
UNITS "table entries"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum number of dsmonMatrix entries in this report.
When the associated dsmonMatrixTopNCtlRequestedSize object
is created or modified, the probe SHOULD set this object as
closely to the requested value as is possible for the
particular implementation and available resources. The
probe MUST NOT lower this value except as a result of a
set to the associated dsmonMatrixTopNCtlRequestedSize
object.
Protocol entries with the highest value of
dsmonMatrixTopNRate or dsmonMatrixTopNHCRate (depending on
the value of the associated dsmonMatrixTopNCtlRateBase
object) shall be placed in this table in decreasing order of
this rate until there is no more room or until there are no
more dsmonMatrix entries."
::= { dsmonMatrixTopNCtlEntry 8 }
dsmonMatrixTopNCtlStartTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime when this top N report was last
started. In other words, this is the time that the
associated dsmonMatrixTopNCtlTimeRemaining object was
modified to start the requested report or the time the
report was last automatically (re)started.
This object may be used by the management station to
determine if a report was missed or not."
::= { dsmonMatrixTopNCtlEntry 9 }
dsmonMatrixTopNCtlOwner OBJECT-TYPE
SYNTAX OwnerString
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The entity that configured this entry and is therefore
using the resources assigned to it."
::= { dsmonMatrixTopNCtlEntry 10 }
dsmonMatrixTopNCtlStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this dsmonMatrixTopNCtlEntry.
An entry MUST NOT exist in the active state unless all
objects in the entry have an appropriate value.
If this object is not equal to active(1), all associated
entries in the dsmonMatrixTopNTable shall be deleted by the
agent."
::= { dsmonMatrixTopNCtlEntry 11 }
--
-- dsmonMatrix TopN Table
--
dsmonMatrixTopNTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonMatrixTopNEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A set of statistics for those dsmonMatrix entries that have
counted the highest number of octets or packets.
If the dsmonAggControlLocked object is equal to 'false',
then all entries in this table SHALL be deleted, and the
agent will not process TopN reports on behalf of any
dsmonMatrixTopNCtlEntry.
When the dsmonAggControlLocked object is set to 'true', then
particular reports SHOULD be restarted from the beginning,
on behalf of all active rows in the dsmonMatrixTopNCtlTable.
Note that dsmonMatrix entries which did not increment at all
during the report interval SHOULD NOT be included in
dsmonMatrixTopN reports."
::= { dsmonMatrixObjects 5 }
dsmonMatrixTopNEntry OBJECT-TYPE
SYNTAX DsmonMatrixTopNEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in the dsmonMatrixTopNTable.
The dsmonMatrixTopNCtlIndex value in the index identifies
the dsmonMatrixTopNCtlEntry on whose behalf this entry was
created.
Entries in this table are ordered from 1 to 'N', where lower
numbers represent higher values of the rate base object,
over the report interval."
INDEX { dsmonMatrixTopNCtlIndex, dsmonMatrixTopNIndex }
::= { dsmonMatrixTopNTable 1 }
DsmonMatrixTopNEntry ::= SEQUENCE {
dsmonMatrixTopNIndex Integer32,
dsmonMatrixTopNAggGroup DsmonCounterAggGroupIndex,
dsmonMatrixTopNNLIndex Integer32,
dsmonMatrixTopNSourceAddress OCTET STRING,
dsmonMatrixTopNDestAddress OCTET STRING,
dsmonMatrixTopNALIndex Integer32,
dsmonMatrixTopNPktRate Gauge32,
dsmonMatrixTopNPktRateOvfl Gauge32,
dsmonMatrixTopNHCPktRate CounterBasedGauge64,
dsmonMatrixTopNRevPktRate Gauge32,
dsmonMatrixTopNRevPktRateOvfl Gauge32,
dsmonMatrixTopNHCRevPktRate CounterBasedGauge64,
dsmonMatrixTopNOctetRate Gauge32,
dsmonMatrixTopNOctetRateOvfl Gauge32,
dsmonMatrixTopNHCOctetRate CounterBasedGauge64,
dsmonMatrixTopNRevOctetRate Gauge32,
dsmonMatrixTopNRevOctetRateOvfl Gauge32,
dsmonMatrixTopNHCRevOctetRate CounterBasedGauge64
}
dsmonMatrixTopNIndex OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An index that uniquely identifies an entry in the
dsmonMatrixTopNTable among those in the same report. This
index is between 1 and N, where N is the number of entries
in this report."
::= { dsmonMatrixTopNEntry 1 }
dsmonMatrixTopNAggGroup OBJECT-TYPE
SYNTAX DsmonCounterAggGroupIndex
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter aggregation group index value associated with
host identified in this entry. This object identifies the
dsmonAggGroupEntry with the same dsmonAggControlIndex value
as the associated dsmonMatrixCtlAggProfile object and the
same dsmonAggGroupIndex value as this object."
::= { dsmonMatrixTopNEntry 2 }
dsmonMatrixTopNNLIndex OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The protocolDirLocalIndex value which identifies the
protocol associated with the dsmonMatrixTopNSourceAddress
and dsmonMatrixTopNDestAddress objects in this entry.
If the protocolDirEntry associated with the
protocolDirLocalIndex with the same value as this object is
de-activated or deleted, then the agent MUST delete this
dsmonMatrixTopN entry."
::= { dsmonMatrixTopNEntry 3 }
dsmonMatrixTopNSourceAddress OBJECT-TYPE
SYNTAX OCTET STRING
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The dsmonMatrixSDSourceAddress value for the source network
host identified in this entry. The associated
dsmonMatrixTopNNLIndex object identifies the network
protocol type and the encoding rules for this object."
::= { dsmonMatrixTopNEntry 4 }
dsmonMatrixTopNDestAddress OBJECT-TYPE
SYNTAX OCTET STRING
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The dsmonMatrixSDDestAddress value for the destination
network host identified in this entry. The associated
dsmonMatrixTopNNLIndex object identifies the network
protocol type and the encoding rules for this object."
::= { dsmonMatrixTopNEntry 5 }
dsmonMatrixTopNALIndex OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The protocolDirLocalIndex value which identifies the
application protocol associated with this entry.
If the protocolDirEntry associated with the
protocolDirLocalIndex with the same value as this object is
de-activated or deleted, then the agent MUST delete this
dsmonMatrixTopN entry."
::= { dsmonMatrixTopNEntry 6 }
dsmonMatrixTopNPktRate OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of packets seen of this protocol from the source
host to the destination host during this sampling interval,
counted using the rules for counting the dsmonMatrixSDPkts
object.
If the value of dsmonMatrixTopNCtlRateBase is
dsmonMatrixTopNPkts, this variable will be used to sort this
report.
If the value of the dsmonMatrixTopNCtlRateBase is
dsmonMatrixTopNHCPkts or dsmonMatrixTopNHCOctets, then this
object will contain the the least significant 32 bits of the
associated dsmonMatrixTopNHCPktRate object."
::= { dsmonMatrixTopNEntry 7 }
dsmonMatrixTopNPktRateOvfl OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The most significant 32 bits of the associated
dsmonMatrixTopNHCPktRate object.
If the associated dsmonMatrixTopNCtlRateBase is equal to
dsmonMatrixTopNHCPkts or dsmonMatrixTopNHCOctets, then this
object will contain the most significant 32 bits of the
associated dsmonMatrixTopNHCPktRate object, otherwise this
object will contain the value zero.
The agent MAY choose not to instantiate this object if High
Capacity monitoring is not supported."
::= { dsmonMatrixTopNEntry 8 }
dsmonMatrixTopNHCPktRate OBJECT-TYPE
SYNTAX CounterBasedGauge64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of packets seen of this protocol from the source
host to the destination host during this sampling interval,
counted using the rules for counting the dsmonMatrixSDHCPkts
object.
If the value of dsmonMatrixTopNCtlRateBase is
dsmonMatrixTopNHCPkts, this variable will be used to sort
this report.
The agent MAY choose not to instantiate this object if High
Capacity monitoring is not supported."
::= { dsmonMatrixTopNEntry 9 }
dsmonMatrixTopNRevPktRate OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of packets seen of this protocol from the
destination host to the source host during this sampling
interval, counted using the rules for counting the
dsmonMatrixDSPkts object (note that the corresponding
dsmonMatrixSDPkts object selected is the one whose source
address is equal to dsmonMatrixTopNDestAddress and whose
destination address is equal to
dsmonMatrixTopNSourceAddress.)"
::= { dsmonMatrixTopNEntry 10 }
dsmonMatrixTopNRevPktRateOvfl OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The most significant 32 bits of the associated
dsmonMatrixTopNHCRevPktRate object.
If the associated dsmonMatrixTopNCtlRateBase is equal to
dsmonMatrixTopNHCPkts or dsmonMatrixTopNHCOCtets, then this
object will contain the most significant 32 bits of the
associated dsmonMatrixTopNHCRevPktRate object, otherwise
this object will contain the value zero.
The agent MAY choose not to instantiate this object if High
Capacity monitoring is not supported."
::= { dsmonMatrixTopNEntry 11 }
dsmonMatrixTopNHCRevPktRate OBJECT-TYPE
SYNTAX CounterBasedGauge64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of packets seen of this protocol from the
destination host to the source host during this sampling
interval, counted using the rules for counting the
dsmonMatrixDSHCPkts object (note that the corresponding
dsmonMatrixSDHCPkts object selected is the one whose source
address is equal to dsmonMatrixTopNDestAddress and whose
destination address is equal to
dsmonMatrixTopNSourceAddress.)
The agent MAY choose not to instantiate this object if High
Capacity monitoring is not supported."
::= { dsmonMatrixTopNEntry 12 }
dsmonMatrixTopNOctetRate OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets seen of this protocol from the source
host to the destination host during this sampling interval,
counted using the rules for counting the dsmonMatrixSDOctets
object.
If the value of dsmonMatrixTopNCtlRateBase is
dsmonMatrixTopNOctets, this variable will be used to sort
this report.
If the value of the dsmonMatrixTopNCtlRateBase is
dsmonMatrixTopNHCPkts or dsmonMatrixTopNHCOctets, then this
object will contain the the least significant 32 bits of the
associated dsmonMatrixTopNHCPktRate object."
::= { dsmonMatrixTopNEntry 13 }
dsmonMatrixTopNOctetRateOvfl OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The most significant 32 bits of the associated
dsmonMatrixTopNHCOctetRate object.
If the associated dsmonMatrixTopNCtlRateBase is equal to
dsmonMatrixTopNHCPkts or dsmonMatrixTopNHCOctets, then this
object will contain the most significant 32 bits of the
associated dsmonMatrixTopNHCOctetRate object, otherwise this
object will contain the value zero.
The agent MAY choose not to instantiate this object if High
Capacity monitoring is not supported."
::= { dsmonMatrixTopNEntry 14 }
dsmonMatrixTopNHCOctetRate OBJECT-TYPE
SYNTAX CounterBasedGauge64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets seen of this protocol from the source
host to the destination host during this sampling interval,
counted using the rules for counting the
dsmonMatrixSDHCOctets object.
If the value of dsmonMatrixTopNCtlRateBase is
dsmonMatrixTopNHCOctets, this variable will be used to sort
this report.
The agent MAY choose not to instantiate this object if High
Capacity monitoring is not supported."
::= { dsmonMatrixTopNEntry 15 }
dsmonMatrixTopNRevOctetRate OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets seen of this protocol from the
destination host to the source host during this sampling
interval, counted using the rules for counting the
dsmonMatrixDSOctets object (note that the corresponding
dsmonMatrixSDOctets object selected is the one whose source
address is equal to dsmonMatrixTopNDestAddress and whose
destination address is equal to
dsmonMatrixTopNSourceAddress.)"
::= { dsmonMatrixTopNEntry 16 }
dsmonMatrixTopNRevOctetRateOvfl OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The most significant 32 bits of the associated
dsmonMatrixTopNHCRevOctetRate object.
If the associated dsmonMatrixTopNCtlRateBase is equal to
dsmonMatrixTopNHCPkts or dsmonMatrixTopNHCOCtets, then this
object will contain the most significant 32 bits of the
associated dsmonMatrixTopNHCRevPktRate object, otherwise
this object will contain the value zero.
The agent MAY choose not to instantiate this object if High
Capacity monitoring is not supported."
::= { dsmonMatrixTopNEntry 17 }
dsmonMatrixTopNHCRevOctetRate OBJECT-TYPE
SYNTAX CounterBasedGauge64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets seen of this protocol from the
destination host to the source host during this sampling
interval, counted using the rules for counting the
dsmonMatrixDSHCOctets object (note that the corresponding
dsmonMatrixSDHCOctets object selected is the one whose
source address is equal to dsmonMatrixTopNDestAddress and
whose destination address is equal to
dsmonMatrixTopNSourceAddress.)
The agent MAY choose not to instantiate this object if High
Capacity monitoring is not supported."
::= { dsmonMatrixTopNEntry 18 }
--
-- Conformance Section
--
dsmonCompliances OBJECT IDENTIFIER ::= { dsmonConformance 1 }
dsmonGroups OBJECT IDENTIFIER ::= { dsmonConformance 2 }
--
-- Compliance for agents that do not support HC or Counter64
--
dsmonCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"Describes the requirements for conformance to the
Differentiated Services Monitoring MIB."
MODULE -- this module
MANDATORY-GROUPS {
dsmonCounterAggControlGroup,
dsmonStatsGroup,
dsmonCapsGroup
}
GROUP dsmonStatsHCGroup
DESCRIPTION
"The dsmonStatsHCGroup is mandatory for systems which
implement High Capacity monitoring."
GROUP dsmonPdistGroup
DESCRIPTION
"The dsmonPdistGroup is mandatory for systems which
implement RMON-2 protocolDirTable based protocol
distribution monitoring."
GROUP dsmonPdistHCGroup
DESCRIPTION
"The dsmonPdistHCGroup is mandatory for systems which
implement RMON-2 protocolDirTable based protocol
distribution monitoring on high capacity interfaces."
GROUP dsmonHostGroup
DESCRIPTION
"The dsmonHostGroup is mandatory for systems which implement
RMON-2 nlHostTable based network protocol monitoring."
GROUP dsmonHostHCGroup
DESCRIPTION
"The dsmonHostHCGroup is mandatory for systems which
implement RMON-2 nlHostTable based network protocol
monitoring, on high capacity interfaces."
GROUP dsmonMatrixGroup
DESCRIPTION
"The dsmonMatrixGroup is mandatory for systems which
implement RMON-2 alMatrix based application protocol
monitoring."
GROUP dsmonMatrixHCGroup
DESCRIPTION
"The dsmonMatrixHCGroup is mandatory for systems which
implement RMON-2 alMatrix based application protocol
monitoring, on high capacity interfaces."
::= { dsmonCompliances 1 }
--
-- Compliance for agents that support HC and Counter64
--
dsmonHCCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"Describes the requirements for conformance to the
Differentiated Services Monitoring MIB for agents which also
support High Capacity monitoring and the Counter64 data
type."
MODULE -- this module
MANDATORY-GROUPS {
dsmonCounterAggControlGroup,
dsmonStatsGroup,
dsmonStatsHCGroup,
dsmonCapsGroup
}
GROUP dsmonPdistGroup
DESCRIPTION
"The dsmonPdistGroup is mandatory for systems which
implement RMON-2 protocolDirTable based protocol
distribution monitoring."
GROUP dsmonPdistHCGroup
DESCRIPTION
"The dsmonPdistHCGroup is mandatory for systems which
implement RMON-2 protocolDirTable based protocol
distribution monitoring."
GROUP dsmonHostGroup
DESCRIPTION
"The dsmonHostGroup is mandatory for systems which implement
RMON-2 nlHostTable based network protocol monitoring."
GROUP dsmonHostHCGroup
DESCRIPTION
"The dsmonHostHCGroup is mandatory for systems which
implement RMON-2 nlHostTable based network protocol
monitoring."
GROUP dsmonMatrixGroup
DESCRIPTION
"The dsmonMatrixGroup is mandatory for systems which
implement RMON-2 alMatrix based application protocol
monitoring."
GROUP dsmonMatrixHCGroup
DESCRIPTION
"The dsmonMatrixHCGroup is mandatory for systems which
implement RMON-2 alMatrix based application protocol
monitoring."
::= { dsmonCompliances 2 }
--
-- Compliance for agents that support HC, but not Counter64
--
dsmonHCNoC64Compliance MODULE-COMPLIANCE
STATUS deprecated
DESCRIPTION
"Describes the requirements for conformance to the
Differentiated Services Monitoring MIB for an agent which
supports high capacity monitoring, but does not support the
Counter64 data type (e.g., only supports the SNMPv1
protocol)."
MODULE -- this module
MANDATORY-GROUPS {
dsmonCounterAggControlGroup,
dsmonStatsGroup,
dsmonStatsOvflGroup,
dsmonCapsGroup
}
GROUP dsmonStatsHCGroup
DESCRIPTION
"Implementation of the dsmonStatsHCGroup is not required.
High Capacity monitoring."
GROUP dsmonPdistGroup
DESCRIPTION
"The dsmonPdistGroup is mandatory for systems which
implement RMON-2 protocolDirTable based protocol
distribution monitoring."
GROUP dsmonPdistOvflGroup
DESCRIPTION
"The dsmonPdistGroup is mandatory for systems which
implement RMON-2 protocolDirTable based protocol
distribution monitoring."
GROUP dsmonPdistHCGroup
DESCRIPTION
"Implementation of the dsmonPdistHCGroup is not required."
GROUP dsmonHostGroup
DESCRIPTION
"The dsmonHostGroup is mandatory for systems which implement
RMON-2 nlHostTable based network protocol monitoring."
GROUP dsmonHostOvflGroup
DESCRIPTION
"The dsmonHostGroup is mandatory for systems which implement
RMON-2 nlHostTable based network protocol monitoring."
GROUP dsmonHostHCGroup
DESCRIPTION
"Implementation of the dsmonHostHCGroup is not required."
GROUP dsmonMatrixGroup
DESCRIPTION
"The dsmonMatrixGroup is mandatory for systems which
implement RMON-2 alMatrix based application protocol
monitoring."
GROUP dsmonMatrixOvflGroup
DESCRIPTION
"The dsmonMatrixGroup is mandatory for systems which
implement RMON-2 alMatrix based application protocol
monitoring."
GROUP dsmonMatrixHCGroup
DESCRIPTION
"Implementation of the dsmonMatrixHCGroup is not required."
::= { dsmonCompliances 3 }
-- Object Groups
dsmonCounterAggControlGroup OBJECT-GROUP
OBJECTS {
dsmonMaxAggGroups,
dsmonAggControlLocked,
dsmonAggControlChanges,
dsmonAggControlLastChangeTime,
dsmonAggControlDescr,
dsmonAggControlOwner,
dsmonAggControlStatus,
dsmonAggGroupIndex,
dsmonAggGroupDescr,
dsmonAggGroupStatus
}
STATUS current
DESCRIPTION
"A collection of objects used to configure and manage
counter aggregation groups for DSMON collection purposes."
::= { dsmonGroups 1 }
dsmonStatsGroup OBJECT-GROUP
OBJECTS {
dsmonStatsControlDataSource,
dsmonStatsControlAggProfile,
dsmonStatsControlDroppedFrames,
dsmonStatsControlCreateTime,
dsmonStatsControlOwner,
dsmonStatsControlStatus,
dsmonStatsInPkts,
dsmonStatsInOctets,
dsmonStatsOutPkts,
dsmonStatsOutOctets
}
STATUS current
DESCRIPTION
"A collection of objects providing per DSCP statistics."
::= { dsmonGroups 2 }
dsmonStatsOvflGroup OBJECT-GROUP
OBJECTS {
dsmonStatsInOvflPkts,
dsmonStatsInOvflOctets,
dsmonStatsOutOvflPkts,
dsmonStatsOutOvflOctets
}
STATUS deprecated
DESCRIPTION
"A collection of objects providing per-DSCP overflow
counters for systems with high capacity data sources, but
without support for the Counter64 data type."
::= { dsmonGroups 3 }
dsmonStatsHCGroup OBJECT-GROUP
OBJECTS {
dsmonStatsInHCPkts,
dsmonStatsInHCOctets,
dsmonStatsOutHCPkts,
dsmonStatsOutHCOctets
}
STATUS current
DESCRIPTION
"A collection of objects providing per DSCP statistics for
high capacity data sources."
::= { dsmonGroups 4 }
dsmonPdistGroup OBJECT-GROUP
OBJECTS {
dsmonPdistCtlDataSource,
dsmonPdistCtlAggProfile,
dsmonPdistCtlMaxDesiredEntries,
dsmonPdistCtlDroppedFrames,
dsmonPdistCtlInserts,
dsmonPdistCtlDeletes,
dsmonPdistCtlCreateTime,
dsmonPdistCtlOwner,
dsmonPdistCtlStatus,
dsmonPdistStatsPkts,
dsmonPdistStatsOctets,
dsmonPdistStatsCreateTime,
dsmonPdistTopNCtlPdistIndex,
dsmonPdistTopNCtlRateBase,
dsmonPdistTopNCtlTimeRemaining,
dsmonPdistTopNCtlGeneratedReprts,
dsmonPdistTopNCtlDuration,
dsmonPdistTopNCtlRequestedSize,
dsmonPdistTopNCtlGrantedSize,
dsmonPdistTopNCtlStartTime,
dsmonPdistTopNCtlOwner,
dsmonPdistTopNCtlStatus,
dsmonPdistTopNPDLocalIndex,
dsmonPdistTopNAggGroup,
dsmonPdistTopNRate
}
STATUS current
DESCRIPTION
"A collection of objects providing per protocol DSCP
monitoring extensions to the RMON-2 MIB."
::= { dsmonGroups 5 }
dsmonPdistOvflGroup OBJECT-GROUP
OBJECTS {
dsmonPdistStatsOvflPkts,
dsmonPdistStatsOvflOctets,
dsmonPdistTopNRateOvfl
}
STATUS deprecated
DESCRIPTION
"A collection of objects providing per-protocol DSCP
overflow counters for systems with high capacity data
sources, but without support for the Counter64 data type."
::= { dsmonGroups 6 }
dsmonPdistHCGroup OBJECT-GROUP
OBJECTS {
dsmonPdistStatsHCPkts,
dsmonPdistStatsHCOctets,
dsmonPdistTopNHCRate
}
STATUS current
DESCRIPTION
"A collection of objects providing per protocol DSCP
monitoring extensions to the RMON-2 MIB for High Capacity
networks."
::= { dsmonGroups 7 }
dsmonHostGroup OBJECT-GROUP
OBJECTS {
dsmonHostCtlDataSource,
dsmonHostCtlAggProfile,
dsmonHostCtlMaxDesiredEntries,
dsmonHostCtlIPv4PrefixLen,
dsmonHostCtlIPv6PrefixLen,
dsmonHostCtlDroppedFrames,
dsmonHostCtlInserts,
dsmonHostCtlDeletes,
dsmonHostCtlCreateTime,
dsmonHostCtlOwner,
dsmonHostCtlStatus,
dsmonHostInPkts,
dsmonHostInOctets,
dsmonHostOutPkts,
dsmonHostOutOctets,
dsmonHostCreateTime,
dsmonHostTopNCtlHostIndex,
dsmonHostTopNCtlRateBase,
dsmonHostTopNCtlTimeRemaining,
dsmonHostTopNCtlGeneratedReports,
dsmonHostTopNCtlDuration,
dsmonHostTopNCtlRequestedSize,
dsmonHostTopNCtlGrantedSize,
dsmonHostTopNCtlStartTime,
dsmonHostTopNCtlOwner,
dsmonHostTopNCtlStatus,
dsmonHostTopNPDLocalIndex,
dsmonHostTopNAddress,
dsmonHostTopNAggGroup,
dsmonHostTopNRate
}
STATUS current
DESCRIPTION
"A collection of objects providing per Host monitoring
functions."
::= { dsmonGroups 8 }
dsmonHostOvflGroup OBJECT-GROUP
OBJECTS {
dsmonHostInOvflPkts,
dsmonHostInOvflOctets,
dsmonHostOutOvflPkts,
dsmonHostOutOvflOctets,
dsmonHostTopNRateOvfl
}
STATUS deprecated
DESCRIPTION
"A collection of objects providing per host DSCP overflow
counters for systems with high capacity data sources, but
without support for the Counter64 data type."
::= { dsmonGroups 9 }
dsmonHostHCGroup OBJECT-GROUP
OBJECTS {
dsmonHostInHCPkts,
dsmonHostInHCOctets,
dsmonHostOutHCPkts,
dsmonHostOutHCOctets,
dsmonHostTopNHCRate
}
STATUS current
DESCRIPTION
"A collection of objects providing per Host monitoring
functions for High Capacity networks."
::= { dsmonGroups 10 }
dsmonCapsGroup OBJECT-GROUP
OBJECTS {
dsmonCapabilities
}
STATUS current
DESCRIPTION
"A collection of objects providing an indication of the
DSMON monitoring functions supported by the agent."
::= { dsmonGroups 11 }
dsmonMatrixGroup OBJECT-GROUP
OBJECTS {
dsmonMatrixCtlDataSource,
dsmonMatrixCtlAggProfile,
dsmonMatrixCtlMaxDesiredEntries,
dsmonMatrixCtlDroppedFrames,
dsmonMatrixCtlInserts,
dsmonMatrixCtlDeletes,
dsmonMatrixCtlCreateTime,
dsmonMatrixCtlOwner,
dsmonMatrixCtlStatus,
dsmonMatrixSDPkts,
dsmonMatrixSDOctets,
dsmonMatrixSDCreateTime,
dsmonMatrixDSPkts,
dsmonMatrixDSOctets,
dsmonMatrixDSCreateTime,
dsmonMatrixTopNCtlMatrixIndex,
dsmonMatrixTopNCtlRateBase,
dsmonMatrixTopNCtlTimeRemaining,
dsmonMatrixTopNCtlGeneratedRpts,
dsmonMatrixTopNCtlDuration,
dsmonMatrixTopNCtlRequestedSize,
dsmonMatrixTopNCtlGrantedSize,
dsmonMatrixTopNCtlStartTime,
dsmonMatrixTopNCtlOwner,
dsmonMatrixTopNCtlStatus,
dsmonMatrixTopNAggGroup,
dsmonMatrixTopNNLIndex,
dsmonMatrixTopNSourceAddress,
dsmonMatrixTopNDestAddress,
dsmonMatrixTopNALIndex,
dsmonMatrixTopNPktRate,
dsmonMatrixTopNRevPktRate,
dsmonMatrixTopNOctetRate,
dsmonMatrixTopNRevOctetRate
}
STATUS current
DESCRIPTION
"A collection of objects providing per conversation
monitoring functions."
::= { dsmonGroups 12 }
dsmonMatrixOvflGroup OBJECT-GROUP
OBJECTS {
dsmonMatrixSDOvflPkts,
dsmonMatrixSDOvflOctets,
dsmonMatrixDSOvflPkts,
dsmonMatrixDSOvflOctets,
dsmonMatrixTopNPktRateOvfl,
dsmonMatrixTopNRevPktRateOvfl,
dsmonMatrixTopNOctetRateOvfl,
dsmonMatrixTopNRevOctetRateOvfl
}
STATUS deprecated
DESCRIPTION
"A collection of objects providing per conversation
monitoring functions for systems with high capacity data
sources, but without support for the Counter64 data type."
::= { dsmonGroups 13 }
dsmonMatrixHCGroup OBJECT-GROUP
OBJECTS {
dsmonMatrixSDHCPkts,
dsmonMatrixSDHCOctets,
dsmonMatrixDSHCPkts,
dsmonMatrixDSHCOctets,
dsmonMatrixTopNHCPktRate,
dsmonMatrixTopNHCRevPktRate,
dsmonMatrixTopNHCOctetRate,
dsmonMatrixTopNHCRevOctetRate
}
STATUS current
DESCRIPTION
"A collection of objects providing per conversation
monitoring functions for High Capacity networks."
::= { dsmonGroups 14 }
END