| DOCS-IETF-SUBMGT-MIB DEFINITIONS ::= BEGIN |
| |
| IMPORTS |
| MODULE-IDENTITY, |
| OBJECT-TYPE, |
| Integer32, |
| mib-2 |
| FROM SNMPv2-SMI |
| RowStatus, |
| TruthValue, |
| TimeStamp, |
| StorageType |
| FROM SNMPv2-TC |
| OBJECT-GROUP, |
| MODULE-COMPLIANCE |
| FROM SNMPv2-CONF |
| InetAddressType, |
| InetAddress |
| FROM INET-ADDRESS-MIB |
| docsIfCmtsCmStatusIndex, |
| docsIfCmtsCmStatusEntry |
| FROM DOCS-IF-MIB -- RFC2670 |
| diffServMIBDataPathGroup, |
| diffServMIBClfrGroup, |
| diffServMIBClfrElementGroup, |
| diffServMIBMultiFieldClfrGroup, |
| |
| |
| |
| diffServMIBActionGroup, |
| diffServMIBAlgDropGroup, |
| diffServMIBCounterGroup, |
| diffServDataPathStatus, |
| diffServClfrStatus, |
| diffServClfrElementStatus, |
| diffServMultiFieldClfrAddrType, |
| diffServMultiFieldClfrSrcAddr, |
| diffServMultiFieldClfrDstAddr, |
| diffServAlgDropStatus, |
| diffServDataPathStorage, |
| diffServClfrStorage, |
| diffServClfrElementStorage, |
| diffServMultiFieldClfrStorage, |
| diffServActionStorage, |
| diffServCountActStorage, |
| diffServAlgDropStorage, |
| diffServAlgDropType |
| FROM DIFFSERV-MIB -- RFC3289 |
| ; |
| |
| docsSubMgt MODULE-IDENTITY |
| LAST-UPDATED "200503290000Z" -- March 29, 2005 |
| ORGANIZATION "IETF IP over Cable Data Network (IPCDN) Working |
| Group" |
| CONTACT-INFO |
| " Wilson Sawyer |
| Postal: 50 Kelly Brook Lane |
| East Hampstead, NH 03826 |
| U.S.A. |
| |
| Phone: +1 603 382 7080 |
| E-mail: wsawyer@ieee.org |
| |
| IETF IPCDN Working Group |
| General Discussion: ipcdn@ietf.org |
| Subscribe: http://www.ietf.org/mailman/listinfo/ipcdn |
| Archive: ftp://ftp.ietf.org/ietf-mail-archive/ipcdn |
| Co-chairs: Richard Woundy, Richard_Woundy@cable.comcast.com |
| Jean-Francois Mule, jf.mule@cablelabs.com" |
| DESCRIPTION |
| "This is the CMTS centric subscriber management MIB for |
| DOCSIS-compliant CMTS. It provides the objects to allow a Cable |
| Modem Termination operator to control the IP addresses and |
| protocols associated with subscribers' cable modems. |
| |
| |
| |
| |
| |
| |
| Copyright (C) The Internet Society (2005). This version of this |
| MIB module is part of RFC 4036; see the RFC itself for full legal |
| notices." |
| REVISION "200503290000Z" -- March 29, 2005 |
| DESCRIPTION |
| "Initial version, published as RFC 4036. Note that the |
| compliance statements in this version apply only to |
| implementations that support DOCSIS 1.0/1.1/2.0, which |
| are not IPv6-capable." |
| ::= { mib-2 125 } |
| |
| docsSubMgtObjects OBJECT IDENTIFIER ::= { docsSubMgt 1 } |
| |
| docsSubMgtCpeControlTable OBJECT-TYPE |
| SYNTAX SEQUENCE OF DocsSubMgtCpeControlEntry |
| MAX-ACCESS not-accessible |
| STATUS current |
| DESCRIPTION |
| "This table AUGMENTs the docsIfCmtsCmStatusTable, adding |
| four WRITEable objects, as well as a read-only object, all of |
| which reflect the state of subscriber management on a particular |
| CM." |
| ::= { docsSubMgtObjects 1 } |
| |
| docsSubMgtCpeControlEntry OBJECT-TYPE |
| SYNTAX DocsSubMgtCpeControlEntry |
| MAX-ACCESS not-accessible |
| STATUS current |
| DESCRIPTION |
| "A row in the docsSubMgtCpeControlTable. All values are set |
| at successful modem registration, either from the system default, |
| or from objects included in the DOCSIS registration request sent |
| upstream to the CMTS from the CM. The contents of this entry are |
| meaningless unless the corresponding docsIfCmtsCmStatusValue (see |
| reference) is registrationComplete(6). The persistence of this |
| row is determined solely by the lifespan of the corresponding |
| docsIfCmtsCmStatusEntry (normally StorageType=volatile)." |
| |
| REFERENCE |
| "RFC 2670" |
| AUGMENTS { docsIfCmtsCmStatusEntry } |
| ::= {docsSubMgtCpeControlTable 1 } |
| |
| DocsSubMgtCpeControlEntry ::= SEQUENCE |
| { |
| docsSubMgtCpeControlMaxCpeIp Integer32, |
| docsSubMgtCpeControlActive TruthValue, |
| docsSubMgtCpeControlLearnable TruthValue, |
| |
| |
| |
| docsSubMgtCpeControlReset TruthValue, |
| docsSubMgtCpeControlLastReset TimeStamp |
| } |
| |
| docsSubMgtCpeControlMaxCpeIp OBJECT-TYPE |
| SYNTAX Integer32(0..2147483647) |
| MAX-ACCESS read-write |
| STATUS current |
| DESCRIPTION |
| "The number of simultaneous IP addresses permitted behind |
| the CM. If this is set to zero, all CPE traffic from the CM is |
| dropped. If the provisioning object corresponding to |
| docsSubMgtCpeIpTable includes more CPE IP address entries for |
| this modem than the value of this object, then this object is |
| set to the count of the number of rows in docsSubMgtCpeIpTable |
| that have the same docsIfCmtsCmStatusIndex value. (For example, |
| if the CM has 5 IP addresses specified for it, this value is 5.) |
| This limit applies to learned and DOCSIS-provisioned entries |
| but not to entries added through some administrative |
| process at the CMTS. If not set through DOCSIS provisioning, |
| this object defaults to docsSubMgtCpeMaxIpDefault. Note that |
| this object is only meaningful if docsSubMgtCpeControlActive |
| is true." |
| ::= { docsSubMgtCpeControlEntry 1 } |
| |
| docsSubMgtCpeControlActive OBJECT-TYPE |
| SYNTAX TruthValue |
| MAX-ACCESS read-write |
| STATUS current |
| DESCRIPTION |
| "Controls the application of subscriber management to |
| this cable modem. If this is set to true, CMTS-based CPE |
| control is active, and all the actions required by the various |
| filter tables and controls apply at the CMTS. If this is set |
| to false, no subscriber management filtering is done at the |
| CMTS (but other filters may apply). If not set through DOCSIS |
| provisioning, this object defaults to |
| docsSubMgtCpeActiveDefault." |
| ::= { docsSubMgtCpeControlEntry 2 } |
| |
| docsSubMgtCpeControlLearnable OBJECT-TYPE |
| SYNTAX TruthValue |
| MAX-ACCESS read-write |
| STATUS current |
| DESCRIPTION |
| "Controls whether the CMTS may learn (and pass traffic |
| for) CPE IP addresses associated with a cable modem. If this is |
| set to true, the CMTS may learn up to docsSubMgtMaxCpeIp |
| |
| |
| |
| addresses (less any DOCSIS-provisioned entries) related to this |
| CM. Those IP addresses are added (by internal process) to the |
| docsSubMgtCpeIpTable. The nature of the learning mechanism is |
| not specified here. |
| |
| If not set through DOCSIS provisioning, this object defaults to |
| docsSubMgtCpeLearnableDefault. Note that this object is only |
| meaningful if docsSubMgtCpeControlActive is true." |
| ::= { docsSubMgtCpeControlEntry 3 } |
| |
| docsSubMgtCpeControlReset OBJECT-TYPE |
| SYNTAX TruthValue |
| MAX-ACCESS read-write |
| STATUS current |
| DESCRIPTION |
| "This object always returns false on read. If this object is |
| set to true, the rows with 'learned' addresses in |
| docsSubMgtCpeIpTable for this CM are deleted from that table." |
| ::= { docsSubMgtCpeControlEntry 4 } |
| |
| docsSubMgtCpeControlLastReset OBJECT-TYPE |
| SYNTAX TimeStamp |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The value of sysUpTime when docsSubMgtCpeControlReset was |
| last set true. Zero if never reset." |
| DEFVAL { 0 } |
| ::= { docsSubMgtCpeControlEntry 5 } |
| |
| docsSubMgtCpeMaxIpDefault OBJECT-TYPE |
| SYNTAX Integer32(0..2147483647) |
| MAX-ACCESS read-write |
| STATUS current |
| DESCRIPTION |
| "The default value for docsSubMgtCpeControlMaxCpeIp if not |
| signaled in the DOCSIS Registration request. This value should |
| be treated as nonvolatile; if set, its value should persist |
| across device resets." |
| DEFVAL { 16 } |
| ::= { docsSubMgtObjects 2 } |
| |
| docsSubMgtCpeActiveDefault OBJECT-TYPE |
| SYNTAX TruthValue |
| MAX-ACCESS read-write |
| STATUS current |
| DESCRIPTION |
| "The default value for docsSubMgtCpeControlActive if not |
| |
| |
| |
| signaled in the DOCSIS Registration request. This value should |
| be treated as nonvolatile; if set, its value should persist |
| across device resets." |
| DEFVAL { false } |
| ::= { docsSubMgtObjects 3 } |
| |
| docsSubMgtCpeLearnableDefault OBJECT-TYPE |
| SYNTAX TruthValue |
| MAX-ACCESS read-write |
| STATUS current |
| DESCRIPTION |
| "The default value for docsSubMgtCpeControlLearnable if not |
| signaled in the DOCSIS Registration request. This value should |
| be treated as nonvolatile; if set, its value should persist |
| across device resets." |
| DEFVAL { true } |
| ::= { docsSubMgtObjects 4 } |
| |
| docsSubMgtCpeIpTable OBJECT-TYPE |
| SYNTAX SEQUENCE OF DocsSubMgtCpeIpEntry |
| MAX-ACCESS not-accessible |
| STATUS current |
| DESCRIPTION |
| "A table of CPE IP addresses known on a per-CM basis." |
| ::= { docsSubMgtObjects 5 } |
| |
| docsSubMgtCpeIpEntry OBJECT-TYPE |
| SYNTAX DocsSubMgtCpeIpEntry |
| MAX-ACCESS not-accessible |
| STATUS current |
| DESCRIPTION |
| "An entry in the docsSubMgtCpeIpTable. The first index is |
| the specific modem we're referring to, and the second index is |
| the specific CPE IP entry." |
| INDEX { docsIfCmtsCmStatusIndex, |
| docsSubMgtCpeIpIndex } |
| ::= {docsSubMgtCpeIpTable 1 } |
| |
| DocsSubMgtCpeIpEntry ::= SEQUENCE |
| { |
| docsSubMgtCpeIpIndex Integer32, |
| docsSubMgtCpeIpAddressType InetAddressType, |
| docsSubMgtCpeIpAddr InetAddress, |
| docsSubMgtCpeIpLearned TruthValue |
| } |
| |
| docsSubMgtCpeIpIndex OBJECT-TYPE |
| SYNTAX Integer32(1..2147483647) |
| |
| |
| |
| MAX-ACCESS not-accessible |
| STATUS current |
| DESCRIPTION |
| "The index of this CPE IP address relative to the indexed CM. |
| An entry is created either through the included CPE IP addresses |
| in the provisioning object, or via learning. |
| |
| If docsSubMgtCpeControlActive is true and a CMTS receives |
| an IP packet from a CM that contains a source IP address that |
| does not match one of the docsSubMgtCpeIpAddr entries for this |
| CM, one of two things occurs. If the number of entries is less |
| than docsSubMgtCpeControlMaxCpeIp, the source address is added to |
| the table and the packet is forwarded. If the number of entries |
| equals the docsSubMgtCpeControlMaxCpeIp, then the packet is |
| dropped." |
| ::= { docsSubMgtCpeIpEntry 1 } |
| |
| docsSubMgtCpeIpAddressType OBJECT-TYPE |
| SYNTAX InetAddressType |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The type of internet address of docsSubMgtCpeIpAddr." |
| ::= { docsSubMgtCpeIpEntry 2 } |
| |
| docsSubMgtCpeIpAddr OBJECT-TYPE |
| SYNTAX InetAddress |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The IP address either set from provisioning or learned via |
| address gleaning or other forwarding means. See |
| docsSubMgtCpeIpIndex for the mechanism. |
| |
| The type of this address is determined by the value of |
| docsSubMgtCpeIpAddressType." |
| ::= { docsSubMgtCpeIpEntry 3 } |
| |
| docsSubMgtCpeIpLearned OBJECT-TYPE |
| SYNTAX TruthValue |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "If true, this entry was learned from IP packets sent |
| upstream rather than from the provisioning objects." |
| ::= { docsSubMgtCpeIpEntry 4 } |
| |
| docsSubMgtCmFilterTable OBJECT-TYPE |
| |
| |
| |
| SYNTAX SEQUENCE OF DocsSubMgtCmFilterEntry |
| MAX-ACCESS not-accessible |
| STATUS current |
| DESCRIPTION |
| "Binds filter groups to modems, identifying for each modem |
| the upstream and downstream filter groups that apply to packets |
| for that modem. Normally, this table reflects the filter group |
| values signaled by DOCSIS Registration, although values may be |
| overridden by management action. |
| |
| For each of the columns in this table, zero is a distinguished |
| value, indicating that the default filtering action is to be |
| taken rather than that associated with a filter group number. |
| Zero is used if the filter group is not signaled by DOCSIS |
| registration." |
| ::= { docsSubMgtObjects 6 } |
| |
| docsSubMgtCmFilterEntry OBJECT-TYPE |
| SYNTAX DocsSubMgtCmFilterEntry |
| MAX-ACCESS not-accessible |
| STATUS current |
| DESCRIPTION |
| "Binds a filter group to each direction of traffic for a |
| modem. The filters in this entry apply if |
| docsSubMgtCpeControlActive is true. |
| |
| The contents of this entry are meaningless unless the |
| corresponding docsIfCmtsCmStatusValue (see reference) is |
| registrationComplete(6). The persistence of this row is |
| determined solely by the lifespan of the corresponding |
| docsIfCmtsCmStatusEntry (normally StorageType=volatile)." |
| REFERENCE |
| "RFC 2670" |
| AUGMENTS { docsIfCmtsCmStatusEntry } |
| ::= {docsSubMgtCmFilterTable 1 } |
| |
| DocsSubMgtCmFilterEntry ::= SEQUENCE |
| { |
| docsSubMgtCmFilterSubDownstream Integer32, |
| docsSubMgtCmFilterSubUpstream Integer32, |
| docsSubMgtCmFilterCmDownstream Integer32, |
| docsSubMgtCmFilterCmUpstream Integer32 |
| } |
| |
| docsSubMgtCmFilterSubDownstream OBJECT-TYPE |
| SYNTAX Integer32(0..65535) |
| MAX-ACCESS read-write |
| STATUS current |
| |
| |
| |
| DESCRIPTION |
| "The filter group applied to traffic destined for subscribers |
| attached to the referenced CM. Upon row creation, this is set |
| either to zero (use default classification, the |
| diffServClfrElementSpecific=zeroDotZero row of |
| diffServClfrElementTable) or to the value in the provisioning |
| object sent upstream from the CM to the CMTS during registration. |
| The value of this object is the same as that of the filter group |
| index appearing as docsSubMgtFilterGroupIndex." |
| ::= { docsSubMgtCmFilterEntry 1 } |
| |
| docsSubMgtCmFilterSubUpstream OBJECT-TYPE |
| SYNTAX Integer32(0..65535) |
| MAX-ACCESS read-write |
| STATUS current |
| DESCRIPTION |
| "The filter group applied to traffic originating from |
| subscribers attached to the referenced CM. Upon row creation |
| this is set to either zero (use default classification, the |
| diffServClfrElementSpecific=zeroDotZero row of |
| diffServClfrElementTable), or to the value in the provisioning |
| object sent upstream from the CM to the CMTS. The value of this |
| object is the same as that of the filter group index appearing as |
| docsSubMgtFilterGroupIndex." |
| ::= { docsSubMgtCmFilterEntry 2 } |
| |
| docsSubMgtCmFilterCmDownstream OBJECT-TYPE |
| SYNTAX Integer32(0..65535) |
| MAX-ACCESS read-write |
| STATUS current |
| DESCRIPTION |
| "The filter group applied to traffic destined for the |
| referenced CM itself. Upon row creation this is set either to |
| zero (use default classification, the |
| diffServClfrElementSpecific=zeroDotZero row of |
| diffServClfrElementTable), or to the value in the provisioning |
| object sent upstream from the CM to the CMTS during registration. |
| The value of this object is the same as that of the filter group |
| index appearing as docsSubMgtFilterGroupIndex." |
| ::= { docsSubMgtCmFilterEntry 3 } |
| |
| docsSubMgtCmFilterCmUpstream OBJECT-TYPE |
| SYNTAX Integer32(0..65535) |
| MAX-ACCESS read-write |
| STATUS current |
| DESCRIPTION |
| "The filter group applied to traffic originating from the |
| referenced CM itself. This is set upon row creation to either |
| |
| |
| |
| zero (use default classification, the |
| diffServClfrElementSpecific=zeroDotZero row of |
| diffServClfrElementTable), or to the value in the provisioning |
| object sent upstream from the CM to the CMTS during registration. |
| The value of this object is the same as the filter group index |
| appearing as docsSubMgtFilterGroupIndex." |
| ::= { docsSubMgtCmFilterEntry 4 } |
| |
| docsSubMgtFilterGroupTable OBJECT-TYPE |
| SYNTAX SEQUENCE OF DocsSubMgtFilterGroupEntry |
| MAX-ACCESS not-accessible |
| STATUS current |
| DESCRIPTION |
| "Provides a collection of referenceable entries to which |
| diffServClfrElementSpecific refers. This table provides filter |
| group indices that can be compared with those signaled during |
| DOCSIS registration. A packet matches an entry from this table |
| if the packet originated from or is destined to a cable modem |
| that registered this index as one of its four filter groups |
| (see docsSubMgtCmFilterTable), and if the packet direction and |
| MAC address select the use of this index among the four." |
| ::= { docsSubMgtObjects 7 } |
| |
| docsSubMgtFilterGroupEntry OBJECT-TYPE |
| SYNTAX DocsSubMgtFilterGroupEntry |
| MAX-ACCESS not-accessible |
| STATUS current |
| DESCRIPTION |
| "An entry only exists if needed by the |
| diffServClfrElementEntry. A packet matches this entry if the |
| packet's cable modem registered this index as one of its four |
| filter groups (see docsSubMgtCmFilterTable) and if the packet |
| direction and MAC address select the use of this index among |
| the four." |
| INDEX { docsSubMgtFilterGroupIndex } |
| ::= { docsSubMgtFilterGroupTable 1 } |
| |
| DocsSubMgtFilterGroupEntry ::= SEQUENCE |
| { |
| docsSubMgtFilterGroupIndex Integer32 |
| } |
| |
| docsSubMgtFilterGroupIndex OBJECT-TYPE |
| SYNTAX Integer32(1..65535) |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The filter group index, from the set signaled at DOCSIS |
| |
| |
| |
| Registration. Provides a referenceable entry to which |
| diffServClfrElementSpecific points. A packet matches this |
| classifier entry if the packet's cable modem registered this |
| index value as one of its four filter groups, and if the packet |
| direction and MAC address select the use of this index among |
| the four. Because this is the only field in this table, it is |
| read-only, contrary to the usual SMI custom of making indices |
| not-accessible. |
| |
| Note that although zero may be signaled (or defaulted) at DOCSIS |
| Registration to indicate a default filtering group, no such entry |
| appears in this table, as diffServClfrElementSpecific will |
| use a zeroDotZero pointer for that classification." |
| ::= { docsSubMgtFilterGroupEntry 1 } |
| |
| docsSubMgtConformance OBJECT IDENTIFIER ::= { docsSubMgt 2 } |
| docsSubMgtCompliances OBJECT IDENTIFIER ::= |
| { docsSubMgtConformance 1 } |
| docsSubMgtGroups OBJECT IDENTIFIER ::= |
| { docsSubMgtConformance 2 } |
| |
| docsSubMgtBasicCompliance MODULE-COMPLIANCE |
| STATUS current |
| DESCRIPTION |
| "The compliance statement for CMTS devices that implement |
| CMTS centric subscriber management. |
| |
| This compliance statement applies to implementations that |
| support DOCSIS 1.0/1.1/2.0, which are not IPv6 capable." |
| |
| |
| MODULE DIFFSERV-MIB -- RFC3289 |
| MANDATORY-GROUPS { |
| diffServMIBDataPathGroup, |
| diffServMIBClfrGroup, |
| diffServMIBClfrElementGroup, |
| diffServMIBMultiFieldClfrGroup, |
| diffServMIBActionGroup, |
| diffServMIBAlgDropGroup, |
| diffServMIBCounterGroup |
| } |
| |
| OBJECT diffServDataPathStatus -- same as RFC3289 |
| SYNTAX RowStatus { active(1) } |
| WRITE-SYNTAX RowStatus { createAndGo(4), destroy(6) } |
| DESCRIPTION |
| "Support for createAndWait and notInService is not required." |
| |
| |
| |
| |
| OBJECT diffServClfrStatus -- same as RFC3289 |
| SYNTAX RowStatus { active(1) } |
| WRITE-SYNTAX RowStatus { createAndGo(4), destroy(6) } |
| DESCRIPTION |
| "Support for createAndWait and notInService is not required." |
| |
| OBJECT diffServClfrElementStatus -- same as RFC3289 |
| SYNTAX RowStatus { active(1) } |
| WRITE-SYNTAX RowStatus { createAndGo(4), destroy(6) } |
| DESCRIPTION |
| "Support for createAndWait and notInService is not required." |
| |
| OBJECT diffServMultiFieldClfrAddrType |
| SYNTAX InetAddressType { ipv4(1) } |
| DESCRIPTION |
| "An implementation is only required to support IPv4 |
| addresses." |
| |
| OBJECT diffServMultiFieldClfrSrcAddr |
| SYNTAX InetAddress (SIZE(4)) |
| DESCRIPTION |
| "An implementation is only required to support IPv4 |
| addresses." |
| |
| OBJECT diffServMultiFieldClfrDstAddr |
| SYNTAX InetAddress (SIZE(4)) |
| DESCRIPTION |
| "An implementation is only required to support IPv4 |
| addresses." |
| |
| OBJECT diffServAlgDropStatus -- same as RFC3289 |
| SYNTAX RowStatus { active(1) } |
| WRITE-SYNTAX RowStatus { createAndGo(4), destroy(6) } |
| DESCRIPTION |
| "Support for createAndWait and notInService is not required." |
| |
| OBJECT diffServDataPathStorage |
| SYNTAX StorageType { nonVolatile(3) } |
| DESCRIPTION |
| "An implementation is only required to support nonvolatile |
| storage." |
| |
| OBJECT diffServClfrStorage |
| SYNTAX StorageType { nonVolatile(3) } |
| DESCRIPTION |
| "An implementation is only required to support nonvolatile |
| storage." |
| |
| |
| |
| |
| OBJECT diffServClfrElementStorage |
| SYNTAX StorageType { nonVolatile(3) } |
| DESCRIPTION |
| "An implementation is only required to support nonvolatile |
| storage." |
| |
| OBJECT diffServMultiFieldClfrStorage |
| SYNTAX StorageType { nonVolatile(3) } |
| DESCRIPTION |
| "An implementation is only required to support nonvolatile |
| storage." |
| |
| OBJECT diffServActionStorage |
| SYNTAX StorageType { nonVolatile(3) } |
| DESCRIPTION |
| "An implementation is only required to support nonvolatile |
| storage." |
| |
| OBJECT diffServCountActStorage |
| SYNTAX StorageType { nonVolatile(3) } |
| DESCRIPTION |
| "An implementation is only required to support nonvolatile |
| storage." |
| |
| OBJECT diffServAlgDropStorage |
| SYNTAX StorageType { nonVolatile(3) } |
| DESCRIPTION |
| "An implementation is only required to support nonvolatile |
| storage." |
| |
| OBJECT diffServAlgDropType |
| SYNTAX INTEGER { alwaysDrop(5) } |
| DESCRIPTION |
| "For DOCSIS subscriber management, this object is |
| only used to provide packet filtering. Implementations |
| need not support other values of this enumeration." |
| |
| MODULE -- This module i.e., DOCS-IETF-SUBMGT-MIB |
| |
| MANDATORY-GROUPS { |
| docsSubMgtGroup |
| } |
| |
| OBJECT docsSubMgtCpeControlMaxCpeIp |
| SYNTAX Integer32(0..16) |
| DESCRIPTION |
| "An implementation is only required to support up to |
| sixteen addresses per modem." |
| |
| |
| |
| OBJECT docsSubMgtCpeMaxIpDefault |
| SYNTAX Integer32(0..16) |
| DESCRIPTION |
| "An implementation is only required to support up to |
| sixteen addresses per modem." |
| |
| OBJECT docsSubMgtCpeIpAddressType |
| SYNTAX InetAddressType { ipv4(1) } |
| DESCRIPTION |
| "An implementation is only required to support IPv4 |
| addresses." |
| |
| OBJECT docsSubMgtCpeIpAddr |
| SYNTAX InetAddress (SIZE(4)) |
| DESCRIPTION |
| "An implementation is only required to support IPv4 |
| addresses." |
| |
| OBJECT docsSubMgtCmFilterSubDownstream |
| SYNTAX Integer32(0..30) |
| DESCRIPTION |
| "An implementation is only required to support thirty |
| filter groups." |
| |
| OBJECT docsSubMgtCmFilterSubUpstream |
| SYNTAX Integer32(0..30) |
| DESCRIPTION |
| "An implementation is only required to support thirty |
| filter groups." |
| |
| OBJECT docsSubMgtCmFilterCmDownstream |
| SYNTAX Integer32(0..30) |
| DESCRIPTION |
| "An implementation is only required to support thirty |
| filter groups." |
| |
| OBJECT docsSubMgtCmFilterCmUpstream |
| SYNTAX Integer32(0..30) |
| DESCRIPTION |
| "An implementation is only required to support thirty |
| filter groups." |
| |
| ::= { docsSubMgtCompliances 1 } |
| |
| docsSubMgtGroup OBJECT-GROUP |
| OBJECTS { |
| docsSubMgtCpeControlMaxCpeIp, |
| docsSubMgtCpeControlActive, |
| |
| |
| |
| docsSubMgtCpeControlLearnable, |
| docsSubMgtCpeControlReset, |
| docsSubMgtCpeControlLastReset, |
| docsSubMgtCpeMaxIpDefault, |
| docsSubMgtCpeActiveDefault, |
| docsSubMgtCpeLearnableDefault, |
| docsSubMgtCpeIpAddressType, |
| docsSubMgtCpeIpAddr, |
| docsSubMgtCpeIpLearned, |
| docsSubMgtCmFilterSubDownstream, |
| docsSubMgtCmFilterSubUpstream, |
| docsSubMgtCmFilterCmDownstream, |
| docsSubMgtCmFilterCmUpstream, |
| docsSubMgtFilterGroupIndex |
| } |
| STATUS current |
| DESCRIPTION |
| "The objects used to manage host-based cable modems |
| via a set of CMTS enforced controls." |
| ::= { docsSubMgtGroups 1 } |
| |
| END |