| ADSL-LINE-EXT-MIB DEFINITIONS ::= BEGIN |
| |
| IMPORTS |
| Counter32, |
| Integer32, |
| NOTIFICATION-TYPE, |
| MODULE-IDENTITY, |
| OBJECT-TYPE FROM SNMPv2-SMI |
| MODULE-COMPLIANCE, OBJECT-GROUP, |
| NOTIFICATION-GROUP FROM SNMPv2-CONF |
| TEXTUAL-CONVENTION FROM SNMPv2-TC |
| PerfCurrentCount, |
| |
| |
| |
| PerfIntervalCount FROM PerfHist-TC-MIB |
| AdslPerfCurrDayCount, |
| AdslPerfPrevDayCount FROM ADSL-TC-MIB |
| SnmpAdminString FROM SNMP-FRAMEWORK-MIB |
| adslLineAlarmConfProfileEntry, |
| adslLineConfProfileEntry, |
| adslAturIntervalEntry, |
| adslAturPerfDataEntry, |
| adslAtucIntervalEntry, |
| adslAtucPerfDataEntry, |
| adslLineEntry, |
| adslMIB FROM ADSL-LINE-MIB |
| ; |
| |
| adslExtMIB MODULE-IDENTITY |
| |
| LAST-UPDATED "200212100000Z" -- 10 Dec 2002 |
| |
| ORGANIZATION "IETF ADSL MIB Working Group" |
| |
| CONTACT-INFO |
| " |
| Faye Ly |
| Pedestal Networks |
| 6503 Dumbarton Circle, |
| Fremont, CA 94555 |
| Tel: +1 510-578-0158 |
| Fax: +1 510-744-5152 |
| E-Mail: faye@pedestalnetworks.com |
| |
| Gregory Bathrick |
| Nokia Networks |
| 2235 Mercury Way, |
| Fax: +1 707-535-7300 |
| E-Mail: greg.bathrick@nokia.com |
| |
| General Discussion:adslmib@ietf.org |
| To Subscribe: https://www1.ietf.org/mailman/listinfo/adslmib |
| Archive: https://www1.ietf.org/mailman/listinfo/adslmib |
| " |
| DESCRIPTION |
| "Copyright (C) The Internet Society (2002). This version of |
| this MIB module is part of RFC 3440; see the RFC itself for |
| full legal notices. |
| |
| This MIB Module is a supplement to the ADSL-LINE-MIB |
| [RFC2662]." |
| |
| |
| |
| |
| REVISION "200212100000Z" -- 10 dec 2002 |
| DESCRIPTION "Initial Version, published as RFC 3440. This MIB |
| module supplements the ADSL-LINE-MIB [RFC2662]." |
| ::= { adslMIB 3 } |
| |
| adslExtMibObjects OBJECT IDENTIFIER ::= { adslExtMIB 1 } |
| |
| AdslTransmissionModeType ::= TEXTUAL-CONVENTION |
| STATUS current |
| DESCRIPTION |
| "A set of ADSL line transmission modes, with one bit |
| per mode. The notes (F) and (L) denote Full-Rate |
| and G.Lite respectively: |
| Bit 00 : Regional Std. (ANSI T1.413) (F) |
| Bit 01 : Regional Std. (ETSI DTS/TM06006) (F) |
| Bit 02 : G.992.1 POTS non-overlapped (F) |
| Bit 03 : G.992.1 POTS overlapped (F) |
| Bit 04 : G.992.1 ISDN non-overlapped (F) |
| Bit 05 : G.992.1 ISDN overlapped (F) |
| Bit 06 : G.992.1 TCM-ISDN non-overlapped (F) |
| Bit 07 : G.992.1 TCM-ISDN overlapped (F) |
| Bit 08 : G.992.2 POTS non-overlapped (L) |
| Bit 09 : G.992.2 POTS overlapped (L) |
| Bit 10 : G.992.2 with TCM-ISDN non-overlapped (L) |
| Bit 11 : G.992.2 with TCM-ISDN overlapped (L) |
| Bit 12 : G.992.1 TCM-ISDN symmetric (F) |
| " |
| SYNTAX BITS { |
| ansit1413(0), |
| etsi(1), |
| q9921PotsNonOverlapped(2), |
| q9921PotsOverlapped(3), |
| q9921IsdnNonOverlapped(4), |
| q9921isdnOverlapped(5), |
| q9921tcmIsdnNonOverlapped(6), |
| q9921tcmIsdnOverlapped(7), |
| q9922potsNonOverlapeed(8), |
| q9922potsOverlapped(9), |
| q9922tcmIsdnNonOverlapped(10), |
| q9922tcmIsdnOverlapped(11), |
| q9921tcmIsdnSymmetric(12) |
| } |
| |
| adslLineExtTable OBJECT-TYPE |
| SYNTAX SEQUENCE OF AdslLineExtEntry |
| MAX-ACCESS not-accessible |
| STATUS current |
| DESCRIPTION |
| |
| |
| |
| "This table is an extension of RFC 2662. It |
| contains ADSL line configuration and |
| monitoring information. This includes the ADSL |
| line's capabilities and actual ADSL transmission |
| system." |
| ::= { adslExtMibObjects 17 } |
| |
| adslLineExtEntry OBJECT-TYPE |
| SYNTAX AdslLineExtEntry |
| MAX-ACCESS not-accessible |
| STATUS current |
| DESCRIPTION |
| "An entry extends the adslLineEntry defined in |
| [RFC2662]. Each entry corresponds to an ADSL |
| line." |
| AUGMENTS { adslLineEntry } |
| ::= { adslLineExtTable 1 } |
| |
| AdslLineExtEntry ::= |
| SEQUENCE { |
| adslLineTransAtucCap AdslTransmissionModeType, |
| adslLineTransAtucConfig AdslTransmissionModeType, |
| adslLineTransAtucActual AdslTransmissionModeType, |
| adslLineGlitePowerState INTEGER, |
| adslLineConfProfileDualLite SnmpAdminString |
| } |
| |
| adslLineTransAtucCap OBJECT-TYPE |
| SYNTAX AdslTransmissionModeType |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The transmission modes, represented by a |
| bitmask that the ATU-C is capable of |
| supporting. The modes available are limited |
| by the design of the equipment." |
| REFERENCE "Section 7.3.2 ITU G.997.1" |
| ::= { adslLineExtEntry 1 } |
| |
| adslLineTransAtucConfig OBJECT-TYPE |
| SYNTAX AdslTransmissionModeType |
| MAX-ACCESS read-write |
| STATUS current |
| |
| DESCRIPTION |
| "The transmission modes, represented by a bitmask, |
| currently enabled by the ATU-C. The manager can |
| only set those modes that are supported by the |
| |
| |
| |
| ATU-C. An ATU-C's supported modes are provided by |
| AdslLineTransAtucCap." |
| REFERENCE "Section 7.3.2 ITU G.997.1" |
| ::= { adslLineExtEntry 2 } |
| |
| adslLineTransAtucActual OBJECT-TYPE |
| SYNTAX AdslTransmissionModeType |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The actual transmission mode of the ATU-C. |
| During ADSL line initialization, the ADSL |
| Transceiver Unit - Remote terminal end (ATU-R) |
| will determine the mode used for the link. |
| This value will be limited a single transmission |
| mode that is a subset of those modes enabled |
| by the ATU-C and denoted by |
| adslLineTransAtucConfig. After an initialization |
| has occurred, its mode is saved as the 'Current' |
| mode and is persistence should the link go |
| down. This object returns 0 (i.e. BITS with no |
| mode bit set) if the mode is not known." |
| REFERENCE "Section 7.3.2 ITU G.997.1 " |
| ::= { adslLineExtEntry 3 } |
| |
| adslLineGlitePowerState OBJECT-TYPE |
| SYNTAX INTEGER { |
| none(1), |
| l0(2), -- L0 Power on |
| l1(3), -- L1 Power on but reduced |
| l3(4) -- L3 Power off |
| } |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The value of this object specifies the power |
| state of this interface. L0 is power on, L1 is |
| power on but reduced and L3 is power off. Power |
| state cannot be configured by an operator but it |
| can be viewed via the ifOperStatus object for the |
| managed ADSL interface. The value of the object |
| ifOperStatus is set to down(2) if the ADSL |
| interface is in power state L3 and is set to up(1) |
| if the ADSL line interface is in power state L0 or |
| L1. If the object adslLineTransAtucActual is set to |
| a G.992.2 (G.Lite)-type transmission mode, the |
| value of this object will be one of the valid power |
| states: L0(2), L1(3), or L3(4). Otherwise, its |
| |
| |
| |
| value will be none(1)." |
| ::= { adslLineExtEntry 4 } |
| |
| adslLineConfProfileDualLite OBJECT-TYPE |
| SYNTAX SnmpAdminString |
| MAX-ACCESS read-write |
| STATUS current |
| DESCRIPTION |
| "This object extends the definition an ADSL line and |
| associated channels (when applicable) for cases |
| when it is configured in dual mode, and operating |
| in a G.Lite-type mode as denoted by |
| adslLineTransAtucActual. Dual mode exists when the |
| object, adslLineTransAtucConfig, is configured with |
| one or more full-rate modes and one or more G.Lite |
| modes simultaneously. |
| |
| When 'dynamic' profiles are implemented, the value |
| of object is equal to the index of the applicable |
| row in the ADSL Line Configuration Profile Table, |
| AdslLineConfProfileTable defined in ADSL-MIB |
| [RFC2662]. |
| |
| In the case when dual-mode has not been enabled, |
| the value of the object will be equal to the value |
| of the object adslLineConfProfile [RFC2662]. |
| |
| When `static' profiles are implemented, in much |
| like the case of the object, |
| adslLineConfProfileName [RFC2662], this object's |
| value will need to algorithmically represent the |
| characteristics of the line. In this case, the |
| value of the line's ifIndex plus a value indicating |
| the line mode type (e.g., G.Lite, Full-rate) will |
| be used. Therefore, the profile's name is a string |
| concatenating the ifIndex and one of the follow |
| values: Full or Lite. This string will be |
| fixed-length (i.e., 14) with leading zero(s). For |
| example, the profile name for ifIndex that equals |
| '15' and is a full rate line, it will be |
| '0000000015Full'." |
| REFERENCE "Section 5.4 Profiles, RFC 2662" |
| ::= { adslLineExtEntry 5 } |
| |
| adslAtucPerfDataExtTable OBJECT-TYPE |
| |
| SYNTAX SEQUENCE OF AdslAtucPerfDataExtEntry |
| MAX-ACCESS not-accessible |
| |
| |
| |
| STATUS current |
| DESCRIPTION |
| "This table extends adslAtucPerfDataTable [RFC2662] |
| with additional ADSL physical line counter |
| information such as unavailable seconds-line and |
| severely errored seconds-line." |
| ::= { adslExtMibObjects 18 } |
| |
| adslAtucPerfDataExtEntry OBJECT-TYPE |
| SYNTAX AdslAtucPerfDataExtEntry |
| MAX-ACCESS not-accessible |
| STATUS current |
| DESCRIPTION |
| "An entry extends the adslAtucPerfDataEntry defined |
| in [RFC2662]. Each entry corresponds to an ADSL |
| line." |
| AUGMENTS { adslAtucPerfDataEntry } |
| ::= { adslAtucPerfDataExtTable 1 } |
| |
| AdslAtucPerfDataExtEntry ::= |
| SEQUENCE { |
| adslAtucPerfStatFastR Counter32, |
| adslAtucPerfStatFailedFastR Counter32, |
| adslAtucPerfStatSesL Counter32, |
| adslAtucPerfStatUasL Counter32, |
| adslAtucPerfCurr15MinFastR PerfCurrentCount, |
| adslAtucPerfCurr15MinFailedFastR PerfCurrentCount, |
| adslAtucPerfCurr15MinSesL PerfCurrentCount, |
| adslAtucPerfCurr15MinUasL PerfCurrentCount, |
| adslAtucPerfCurr1DayFastR AdslPerfCurrDayCount, |
| adslAtucPerfCurr1DayFailedFastR AdslPerfCurrDayCount, |
| adslAtucPerfCurr1DaySesL AdslPerfCurrDayCount, |
| adslAtucPerfCurr1DayUasL AdslPerfCurrDayCount, |
| adslAtucPerfPrev1DayFastR AdslPerfPrevDayCount, |
| adslAtucPerfPrev1DayFailedFastR AdslPerfPrevDayCount, |
| adslAtucPerfPrev1DaySesL AdslPerfPrevDayCount, |
| adslAtucPerfPrev1DayUasL AdslPerfPrevDayCount |
| } |
| |
| adslAtucPerfStatFastR OBJECT-TYPE |
| SYNTAX Counter32 |
| UNITS "line retrains" |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The value of this object reports the count of |
| the number of fast line bs since last |
| agent reset." |
| |
| |
| |
| REFERENCE "ITU G.997.1 Section 7.4.15.1 " |
| ::= { adslAtucPerfDataExtEntry 1 } |
| |
| adslAtucPerfStatFailedFastR OBJECT-TYPE |
| SYNTAX Counter32 |
| UNITS "line retrains" |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The value of this object reports the count of |
| the number of failed fast line retrains since |
| last agent reset." |
| REFERENCE "ITU G.997.1 Section 7.4.15.2 " |
| ::= { adslAtucPerfDataExtEntry 2 } |
| |
| adslAtucPerfStatSesL OBJECT-TYPE |
| SYNTAX Counter32 |
| UNITS "seconds" |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The value of this object reports the count of |
| the number of severely errored seconds-line since |
| last agent reset." |
| REFERENCE "ITU G.997.1 Section 7.2.1.1.7 " |
| ::= { adslAtucPerfDataExtEntry 3 } |
| |
| adslAtucPerfStatUasL OBJECT-TYPE |
| SYNTAX Counter32 |
| UNITS "seconds" |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The value of this object reports the count of |
| the number of unavailable seconds-line since |
| last agent reset." |
| REFERENCE "ITU G.997.1 Section 7.2.1.1.9 " |
| ::= { adslAtucPerfDataExtEntry 4 } |
| |
| adslAtucPerfCurr15MinFastR OBJECT-TYPE |
| SYNTAX PerfCurrentCount |
| UNITS "seconds" |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "For the current 15-minute interval, |
| adslAtucPerfCurr15MinFastR reports the current |
| number of seconds during which there have been |
| |
| |
| |
| fast retrains." |
| REFERENCE "ITU G.997.1 Section 7.4.15.1 " |
| ::= { adslAtucPerfDataExtEntry 5 } |
| |
| adslAtucPerfCurr15MinFailedFastR OBJECT-TYPE |
| SYNTAX PerfCurrentCount |
| UNITS "seconds" |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "For the current 15-minute interval, |
| adslAtucPerfCurr15MinFailedFastR reports the |
| current number of seconds during which there |
| have been failed fast retrains." |
| REFERENCE "ITU G.997.1 Section 7.4.15.2 " |
| ::= { adslAtucPerfDataExtEntry 6 } |
| |
| adslAtucPerfCurr15MinSesL OBJECT-TYPE |
| SYNTAX PerfCurrentCount |
| UNITS "seconds" |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "For the current 15-minute interval, |
| adslAtucPerfCurr15MinSesL reports the current |
| number of seconds during which there have been |
| severely errored seconds-line." |
| REFERENCE "ITU G.997.1 Section 7.2.1.1.7 " |
| ::= { adslAtucPerfDataExtEntry 7 } |
| |
| adslAtucPerfCurr15MinUasL OBJECT-TYPE |
| SYNTAX PerfCurrentCount |
| UNITS "seconds" |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "For the current 15-minute interval, |
| adslAtucPerfCurr15MinUasL reports the current |
| number of seconds during which there have been |
| unavailable seconds-line." |
| REFERENCE "ITU G.997.1 Section 7.2.1.1.9 " |
| ::= { adslAtucPerfDataExtEntry 8 } |
| |
| adslAtucPerfCurr1DayFastR OBJECT-TYPE |
| SYNTAX AdslPerfCurrDayCount |
| UNITS "seconds" |
| MAX-ACCESS read-only |
| STATUS current |
| |
| |
| |
| DESCRIPTION |
| "For the current day as measured by |
| adslAtucPerfCurr1DayTimeElapsed [RFC2662], |
| adslAtucPerfCurr1DayFastR reports the number |
| of seconds during which there have been |
| fast retrains." |
| REFERENCE "ITU G.997.1 Section 7.4.15.1 " |
| ::= { adslAtucPerfDataExtEntry 9 } |
| |
| adslAtucPerfCurr1DayFailedFastR OBJECT-TYPE |
| SYNTAX AdslPerfCurrDayCount |
| UNITS "seconds" |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "For the current day as measured by |
| adslAtucPerfCurr1DayTimeElapsed [RFC2662], |
| adslAtucPerfCurr1DayFailedFastR reports the |
| number of seconds during which there have been |
| failed fast retrains." |
| REFERENCE "ITU G.997.1 Section 7.4.15.2 " |
| ::= { adslAtucPerfDataExtEntry 10 } |
| |
| adslAtucPerfCurr1DaySesL OBJECT-TYPE |
| SYNTAX AdslPerfCurrDayCount |
| UNITS "seconds" |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "For the current day as measured by |
| adslAtucPerfCurr1DayTimeElapsed [RFC2662], |
| adslAtucPerfCurr1DaySesL reports the |
| number of seconds during which there have been |
| severely errored seconds-line." |
| REFERENCE "ITU G.997.1 Section 7.2.1.1.7 " |
| ::= { adslAtucPerfDataExtEntry 11 } |
| |
| adslAtucPerfCurr1DayUasL OBJECT-TYPE |
| SYNTAX AdslPerfCurrDayCount |
| UNITS "seconds" |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "For the current day as measured by |
| adslAtucPerfCurr1DayTimeElapsed [RFC2662], |
| adslAtucPerfCurr1DayUasL reports the |
| number of seconds during which there have been |
| unavailable seconds-line." |
| |
| |
| |
| REFERENCE "ITU G.997.1 Section 7.2.1.1.9 " |
| ::= { adslAtucPerfDataExtEntry 12 } |
| |
| adslAtucPerfPrev1DayFastR OBJECT-TYPE |
| SYNTAX AdslPerfPrevDayCount |
| UNITS "seconds" |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "For the previous day, adslAtucPerfPrev1DayFastR |
| reports the number of seconds during which there |
| were fast retrains." |
| REFERENCE "ITU G.997.1 Section 7.4.15.1 " |
| ::= { adslAtucPerfDataExtEntry 13 } |
| |
| adslAtucPerfPrev1DayFailedFastR OBJECT-TYPE |
| SYNTAX AdslPerfPrevDayCount |
| UNITS "seconds" |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "For the previous day, |
| adslAtucPerfPrev1DayFailedFastR reports the number |
| of seconds during which there were failed fast |
| retrains." |
| REFERENCE "ITU G.997.1 Section 7.4.15.2 " |
| ::= { adslAtucPerfDataExtEntry 14 } |
| |
| adslAtucPerfPrev1DaySesL OBJECT-TYPE |
| SYNTAX AdslPerfPrevDayCount |
| UNITS "seconds" |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "For the previous day, adslAtucPerfPrev1DaySesL |
| reports the number of seconds during which there |
| were severely errored seconds-line." |
| REFERENCE "ITU G.997.1 Section 7.2.1.1.7 " |
| ::= { adslAtucPerfDataExtEntry 15 } |
| |
| adslAtucPerfPrev1DayUasL OBJECT-TYPE |
| SYNTAX AdslPerfPrevDayCount |
| UNITS "seconds" |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "For the previous day, adslAtucPerfPrev1DayUasL |
| reports the number of seconds during which there |
| |
| |
| |
| were unavailable seconds-line." |
| REFERENCE "ITU G.997.1 Section 7.2.1.1.9 " |
| ::= { adslAtucPerfDataExtEntry 16 } |
| |
| adslAtucIntervalExtTable OBJECT-TYPE |
| SYNTAX SEQUENCE OF AdslAtucIntervalExtEntry |
| MAX-ACCESS not-accessible |
| STATUS current |
| DESCRIPTION |
| "This table provides one row for each ATU-C |
| performance data collection interval for |
| ADSL physical interfaces whose |
| IfEntries' ifType is equal to adsl(94)." |
| ::= { adslExtMibObjects 19 } |
| |
| adslAtucIntervalExtEntry OBJECT-TYPE |
| SYNTAX AdslAtucIntervalExtEntry |
| MAX-ACCESS not-accessible |
| STATUS current |
| DESCRIPTION "An entry in the |
| adslAtucIntervalExtTable." |
| AUGMENTS { adslAtucIntervalEntry } |
| ::= { adslAtucIntervalExtTable 1 } |
| |
| AdslAtucIntervalExtEntry ::= |
| SEQUENCE { |
| adslAtucIntervalFastR PerfIntervalCount, |
| adslAtucIntervalFailedFastR PerfIntervalCount, |
| adslAtucIntervalSesL PerfIntervalCount, |
| adslAtucIntervalUasL PerfIntervalCount |
| } |
| |
| adslAtucIntervalFastR OBJECT-TYPE |
| SYNTAX PerfIntervalCount |
| UNITS "seconds" |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "For the current interval, adslAtucIntervalFastR |
| reports the current number of seconds during which |
| there have been fast retrains." |
| ::= { adslAtucIntervalExtEntry 1 } |
| |
| adslAtucIntervalFailedFastR OBJECT-TYPE |
| SYNTAX PerfIntervalCount |
| UNITS "seconds" |
| MAX-ACCESS read-only |
| STATUS current |
| |
| |
| |
| DESCRIPTION |
| "For the each interval, adslAtucIntervalFailedFastR |
| reports the number of seconds during which |
| there have been failed fast retrains." |
| ::= { adslAtucIntervalExtEntry 2 } |
| |
| adslAtucIntervalSesL OBJECT-TYPE |
| SYNTAX PerfIntervalCount |
| UNITS "seconds" |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "For the each interval, adslAtucIntervalSesL |
| reports the number of seconds during which |
| there have been severely errored seconds-line." |
| ::= { adslAtucIntervalExtEntry 3 } |
| |
| adslAtucIntervalUasL OBJECT-TYPE |
| SYNTAX PerfIntervalCount |
| UNITS "seconds" |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "For the each interval, adslAtucIntervalUasL |
| reports the number of seconds during which |
| there have been unavailable seconds-line." |
| ::= { adslAtucIntervalExtEntry 4 } |
| |
| adslAturPerfDataExtTable OBJECT-TYPE |
| SYNTAX SEQUENCE OF AdslAturPerfDataExtEntry |
| MAX-ACCESS not-accessible |
| STATUS current |
| DESCRIPTION |
| "This table contains ADSL physical line counters |
| not defined in the adslAturPerfDataTable |
| from the ADSL-LINE-MIB [RFC2662]." |
| ::= { adslExtMibObjects 20 } |
| |
| adslAturPerfDataExtEntry OBJECT-TYPE |
| SYNTAX AdslAturPerfDataExtEntry |
| MAX-ACCESS not-accessible |
| STATUS current |
| DESCRIPTION |
| "An entry extends the adslAturPerfDataEntry defined |
| in [RFC2662]. Each entry corresponds to an ADSL |
| line." |
| AUGMENTS { adslAturPerfDataEntry } |
| ::= { adslAturPerfDataExtTable 1 } |
| |
| |
| |
| AdslAturPerfDataExtEntry ::= |
| SEQUENCE { |
| adslAturPerfStatSesL Counter32, |
| adslAturPerfStatUasL Counter32, |
| adslAturPerfCurr15MinSesL PerfCurrentCount, |
| adslAturPerfCurr15MinUasL PerfCurrentCount, |
| adslAturPerfCurr1DaySesL AdslPerfCurrDayCount, |
| adslAturPerfCurr1DayUasL AdslPerfCurrDayCount, |
| adslAturPerfPrev1DaySesL AdslPerfPrevDayCount, |
| adslAturPerfPrev1DayUasL AdslPerfPrevDayCount |
| } |
| |
| adslAturPerfStatSesL OBJECT-TYPE |
| SYNTAX Counter32 |
| UNITS "seconds" |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The value of this object reports the count of |
| severely errored second-line since the last agent |
| reset." |
| REFERENCE "ITU G.997.1 Section 7.2.1.1.7 " |
| ::= { adslAturPerfDataExtEntry 1 } |
| |
| adslAturPerfStatUasL OBJECT-TYPE |
| SYNTAX Counter32 |
| UNITS "seconds" |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The value of this object reports the count of |
| unavailable seconds-line since the last agent |
| reset." |
| REFERENCE "ITU G.997.1 Section 7.2.1.2.9 " |
| ::= { adslAturPerfDataExtEntry 2 } |
| |
| adslAturPerfCurr15MinSesL OBJECT-TYPE |
| SYNTAX PerfCurrentCount |
| UNITS "seconds" |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "For the current 15-minute interval, |
| adslAturPerfCurr15MinSesL reports the current |
| number of seconds during which there have been |
| severely errored seconds-line." |
| |
| REFERENCE "ITU G.997.1 Section 7.2.1.2.7 " |
| |
| |
| |
| ::= { adslAturPerfDataExtEntry 3 } |
| |
| adslAturPerfCurr15MinUasL OBJECT-TYPE |
| SYNTAX PerfCurrentCount |
| UNITS "seconds" |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "For the current 15-minute interval, |
| adslAturPerfCurr15MinUasL reports the current |
| number of seconds during which there have been |
| available seconds-line." |
| REFERENCE "ITU G.997.1 Section 7.2.1.2.9 " |
| ::= { adslAturPerfDataExtEntry 4 } |
| |
| adslAturPerfCurr1DaySesL OBJECT-TYPE |
| SYNTAX AdslPerfCurrDayCount |
| UNITS "seconds" |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "For the current day as measured by |
| adslAturPerfCurr1DayTimeElapsed [RFC2662], |
| adslAturPerfCurr1DaySesL reports the |
| number of seconds during which there have been |
| severely errored seconds-line." |
| REFERENCE "ITU G.997.1 Section 7.2.1.2.7 " |
| ::= { adslAturPerfDataExtEntry 5 } |
| |
| adslAturPerfCurr1DayUasL OBJECT-TYPE |
| SYNTAX AdslPerfCurrDayCount |
| UNITS "seconds" |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "For the current day as measured by |
| adslAturPerfCurr1DayTimeElapsed [RFC2662], |
| adslAturPerfCurr1DayUasL reports the |
| number of seconds during which there have been |
| unavailable seconds-line." |
| REFERENCE "ITU G.997.1 Section 7.2.1.2.9 " |
| ::= { adslAturPerfDataExtEntry 6 } |
| |
| adslAturPerfPrev1DaySesL OBJECT-TYPE |
| SYNTAX AdslPerfPrevDayCount |
| UNITS "seconds" |
| MAX-ACCESS read-only |
| STATUS current |
| |
| |
| |
| DESCRIPTION |
| "For the previous day, adslAturPerfPrev1DaySesL |
| reports the number of seconds during which there |
| were severely errored seconds-line." |
| REFERENCE "ITU G.997.1 Section 7.2.1.2.7 " |
| ::= { adslAturPerfDataExtEntry 7 } |
| |
| adslAturPerfPrev1DayUasL OBJECT-TYPE |
| SYNTAX AdslPerfPrevDayCount |
| UNITS "seconds" |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "For the previous day, adslAturPerfPrev1DayUasL |
| reports the number of seconds during which there |
| were severely errored seconds-line." |
| REFERENCE "ITU G.997.1 Section 7.2.1.2.9 " |
| ::= { adslAturPerfDataExtEntry 8 } |
| |
| adslAturIntervalExtTable OBJECT-TYPE |
| SYNTAX SEQUENCE OF AdslAturIntervalExtEntry |
| MAX-ACCESS not-accessible |
| STATUS current |
| DESCRIPTION |
| "This table provides one row for each ATU-R |
| performance data collection interval for |
| ADSL physical interfaces whose |
| IfEntries' ifType is equal to adsl(94)." |
| ::= { adslExtMibObjects 21 } |
| |
| adslAturIntervalExtEntry OBJECT-TYPE |
| SYNTAX AdslAturIntervalExtEntry |
| MAX-ACCESS not-accessible |
| STATUS current |
| DESCRIPTION "An entry in the |
| adslAturIntervalExtTable." |
| AUGMENTS { adslAturIntervalEntry } |
| ::= { adslAturIntervalExtTable 1 } |
| |
| AdslAturIntervalExtEntry ::= |
| SEQUENCE { |
| adslAturIntervalSesL PerfIntervalCount, |
| adslAturIntervalUasL PerfIntervalCount |
| } |
| |
| adslAturIntervalSesL OBJECT-TYPE |
| SYNTAX PerfIntervalCount |
| UNITS "seconds" |
| |
| |
| |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "For the each interval, adslAturIntervalSesL |
| reports the number of seconds during which |
| there have been severely errored seconds-line." |
| ::= { adslAturIntervalExtEntry 1 } |
| |
| adslAturIntervalUasL OBJECT-TYPE |
| SYNTAX PerfIntervalCount |
| UNITS "seconds" |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "For the each interval, adslAturIntervalUasL |
| reports the number of seconds during which |
| there have been unavailable seconds-line." |
| ::= { adslAturIntervalExtEntry 2 } |
| |
| adslConfProfileExtTable OBJECT-TYPE |
| SYNTAX SEQUENCE OF AdslConfProfileExtEntry |
| MAX-ACCESS not-accessible |
| STATUS current |
| DESCRIPTION |
| "The adslConfProfileExtTable extends the ADSL line |
| profile configuration information in the |
| adslLineConfProfileTable from the ADSL-LINE-MIB |
| [RFC2662] by adding the ability to configure the |
| ADSL physical line mode." |
| ::= { adslExtMibObjects 22 } |
| |
| adslConfProfileExtEntry OBJECT-TYPE |
| SYNTAX AdslConfProfileExtEntry |
| MAX-ACCESS not-accessible |
| STATUS current |
| DESCRIPTION |
| "An entry extends the adslLineConfProfileEntry |
| defined in [RFC2662]. Each entry corresponds to an |
| ADSL line profile." |
| AUGMENTS { adslLineConfProfileEntry } |
| ::= { adslConfProfileExtTable 1 } |
| |
| AdslConfProfileExtEntry ::= |
| SEQUENCE { |
| adslConfProfileLineType INTEGER |
| } |
| |
| adslConfProfileLineType OBJECT-TYPE |
| |
| |
| |
| SYNTAX INTEGER { |
| noChannel (1), -- no channels exist |
| fastOnly (2), -- only fast channel exists |
| interleavedOnly (3), -- only interleaved channel |
| -- exist |
| fastOrInterleaved (4),-- either fast or interleaved |
| -- channels can exist, but |
| -- only one at any time |
| fastAndInterleaved (5)-- both the fast channel and |
| -- the interleaved channel |
| -- exist |
| } |
| MAX-ACCESS read-create |
| STATUS current |
| DESCRIPTION |
| "This object is used to configure the ADSL physical |
| line mode. It has following valid values: |
| |
| noChannel(1), when no channels exist. |
| fastOnly(2), when only fast channel exists. |
| interleavedOnly(3), when only interleaved channel |
| exist. |
| fastOrInterleaved(4), when either fast or |
| interleaved channels can exist, but only one |
| at any time. |
| fastAndInterleaved(5), when both the fast channel |
| and the interleaved channel exist. |
| |
| In the case when no value has been set, the default |
| Value is noChannel(1). |
| " |
| DEFVAL { fastOnly } |
| ::= { adslConfProfileExtEntry 1 } |
| |
| adslAlarmConfProfileExtTable OBJECT-TYPE |
| SYNTAX SEQUENCE OF AdslAlarmConfProfileExtEntry |
| MAX-ACCESS not-accessible |
| STATUS current |
| DESCRIPTION |
| "This table extends the |
| adslLineAlarmConfProfileTable and provides |
| threshold parameters for all the counters defined |
| in this MIB module." |
| ::= { adslExtMibObjects 23 } |
| |
| adslAlarmConfProfileExtEntry OBJECT-TYPE |
| SYNTAX AdslAlarmConfProfileExtEntry |
| MAX-ACCESS not-accessible |
| |
| |
| |
| STATUS current |
| DESCRIPTION |
| "An entry extends the adslLineAlarmConfProfileTable |
| defined in [RFC2662]. Each entry corresponds to |
| an ADSL alarm profile." |
| AUGMENTS { adslLineAlarmConfProfileEntry } |
| ::= { adslAlarmConfProfileExtTable 1 } |
| |
| AdslAlarmConfProfileExtEntry ::= |
| SEQUENCE { |
| adslAtucThreshold15MinFailedFastR Integer32, |
| adslAtucThreshold15MinSesL Integer32, |
| adslAtucThreshold15MinUasL Integer32, |
| adslAturThreshold15MinSesL Integer32, |
| adslAturThreshold15MinUasL Integer32 |
| } |
| |
| adslAtucThreshold15MinFailedFastR OBJECT-TYPE |
| SYNTAX Integer32(0..900) |
| UNITS "seconds" |
| MAX-ACCESS read-create |
| STATUS current |
| DESCRIPTION |
| "The first time the value of the corresponding |
| instance of adslAtucPerfCurr15MinFailedFastR |
| reaches or exceeds this value within a given |
| 15-minute performance data collection period, |
| an adslAtucFailedFastRThreshTrap notification |
| will be generated. The value '0' will disable |
| the notification. The default value of this |
| object is '0'." |
| DEFVAL { 0 } |
| ::= { adslAlarmConfProfileExtEntry 1 } |
| |
| adslAtucThreshold15MinSesL OBJECT-TYPE |
| SYNTAX Integer32(0..900) |
| UNITS "seconds" |
| MAX-ACCESS read-create |
| STATUS current |
| DESCRIPTION |
| "The first time the value of the corresponding |
| instance of adslAtucPerf15MinSesL reaches or |
| exceeds this value within a given 15-minute |
| performance data collection period, an |
| adslAtucSesLThreshTrap notification will be |
| generated. The value '0' will disable the |
| notification. The default value of this |
| object is '0'." |
| |
| |
| |
| DEFVAL { 0 } |
| |
| ::= { adslAlarmConfProfileExtEntry 2 } |
| |
| adslAtucThreshold15MinUasL OBJECT-TYPE |
| SYNTAX Integer32(0..900) |
| UNITS "seconds" |
| MAX-ACCESS read-create |
| STATUS current |
| DESCRIPTION |
| "The first time the value of the corresponding |
| instance of adslAtucPerf15MinUasL reaches or |
| exceeds this value within a given 15-minute |
| performance data collection period, an |
| adslAtucUasLThreshTrap notification will be |
| generated. The value '0' will disable the |
| notification. The default value of this |
| object is '0'." |
| DEFVAL { 0 } |
| ::= { adslAlarmConfProfileExtEntry 3 } |
| |
| adslAturThreshold15MinSesL OBJECT-TYPE |
| SYNTAX Integer32(0..900) |
| UNITS "seconds" |
| MAX-ACCESS read-create |
| STATUS current |
| DESCRIPTION |
| "The first time the value of the corresponding |
| instance of adslAturPerf15MinSesL reaches or |
| exceeds this value within a given 15-minute |
| performance data collection period, an |
| adslAturSesLThreshTrap notification will be |
| generated. The value '0' will disable the |
| notification. The default value of this |
| object is '0'." |
| DEFVAL { 0 } |
| ::= { adslAlarmConfProfileExtEntry 4 } |
| |
| adslAturThreshold15MinUasL OBJECT-TYPE |
| SYNTAX Integer32(0..900) |
| UNITS "seconds" |
| MAX-ACCESS read-create |
| STATUS current |
| DESCRIPTION |
| "The first time the value of the corresponding |
| instance of adslAturPerf15MinUasL reaches or |
| exceeds this value within a given 15-minute |
| performance data collection period, an |
| |
| |
| |
| adslAturUasLThreshTrap notification will be |
| generated. The value '0' will disable the |
| notification. The default value of this |
| object is '0'." |
| DEFVAL { 0 } |
| |
| ::= { adslAlarmConfProfileExtEntry 5 } |
| |
| -- definitions |
| |
| adslExtTraps OBJECT IDENTIFIER ::= { adslExtMibObjects 24 } |
| |
| adslExtAtucTraps OBJECT IDENTIFIER ::= { adslExtTraps 1 } |
| |
| adslExtAtucTrapsPrefix OBJECT IDENTIFIER ::= { adslExtAtucTraps 0 } |
| |
| adslAtucFailedFastRThreshTrap NOTIFICATION-TYPE |
| OBJECTS { adslAtucPerfCurr15MinFailedFastR } |
| STATUS current |
| DESCRIPTION |
| "Failed Fast Retrains 15-minute threshold reached." |
| ::= { adslExtAtucTrapsPrefix 1 } |
| |
| adslAtucSesLThreshTrap NOTIFICATION-TYPE |
| OBJECTS { adslAtucPerfCurr15MinSesL } |
| STATUS current |
| DESCRIPTION |
| "Severely errored seconds-line 15-minute threshold |
| reached." |
| ::= { adslExtAtucTrapsPrefix 2 } |
| |
| adslAtucUasLThreshTrap NOTIFICATION-TYPE |
| OBJECTS { adslAtucPerfCurr15MinUasL } |
| STATUS current |
| DESCRIPTION |
| "Unavailable seconds-line 15-minute threshold |
| reached." |
| ::= { adslExtAtucTrapsPrefix 3 } |
| |
| |
| adslExtAturTraps OBJECT IDENTIFIER ::= { adslExtTraps 2 } |
| |
| adslExtAturTrapsPrefix OBJECT IDENTIFIER ::= { adslExtAturTraps 0 } |
| |
| adslAturSesLThreshTrap NOTIFICATION-TYPE |
| OBJECTS { adslAturPerfCurr15MinSesL } |
| STATUS current |
| DESCRIPTION |
| |
| |
| |
| "Severely errored seconds-line 15-minute threshold |
| reached." |
| ::= { adslExtAturTrapsPrefix 1 } |
| |
| adslAturUasLThreshTrap NOTIFICATION-TYPE |
| OBJECTS { adslAturPerfCurr15MinUasL } |
| STATUS current |
| DESCRIPTION |
| "Unavailable seconds-line 15-minute threshold |
| reached." |
| ::= { adslExtAturTrapsPrefix 2 } |
| |
| |
| -- conformance information |
| |
| adslExtConformance OBJECT IDENTIFIER ::= { adslExtMIB 2 } |
| |
| adslExtGroups OBJECT IDENTIFIER ::= { adslExtConformance 1 } |
| adslExtCompliances OBJECT IDENTIFIER ::= { adslExtConformance 2 } |
| |
| -- ATU-C agent compliance statements |
| |
| adslExtLineMibAtucCompliance MODULE-COMPLIANCE |
| STATUS current |
| DESCRIPTION |
| "The compliance statement for SNMP entities which |
| represent ADSL ATU-C interfaces." |
| |
| MODULE -- this module |
| MANDATORY-GROUPS |
| { |
| adslExtLineGroup, |
| adslExtLineConfProfileControlGroup, |
| adslExtLineAlarmConfProfileGroup |
| } |
| |
| GROUP adslExtAtucPhysPerfCounterGroup |
| DESCRIPTION |
| "This group is optional. Implementations which |
| require continuous ATU-C physical event counters |
| should implement this group." |
| |
| GROUP adslExtAturPhysPerfCounterGroup |
| DESCRIPTION |
| "This group is optional. Implementations which |
| require continuous ATU-R physical event counters |
| should implement this group." |
| |
| |
| |
| |
| GROUP adslExtNotificationsGroup |
| DESCRIPTION |
| "This group is optional. Implementations which |
| support TCA (Threshold Crossing Alert) should |
| implement this group." |
| |
| OBJECT adslAtucThreshold15MinFailedFastR |
| MIN-ACCESS read-write |
| DESCRIPTION |
| "Read-write access is applicable only when |
| static profiles as defined in ADSL Line MIB |
| [RFC2662] are implemented." |
| |
| OBJECT adslAtucThreshold15MinSesL |
| MIN-ACCESS read-write |
| DESCRIPTION |
| "Read-write access is applicable only when |
| static profiles as defined in ADSL Line MIB |
| [RFC2662] are implemented." |
| |
| OBJECT adslAtucThreshold15MinUasL |
| MIN-ACCESS read-write |
| DESCRIPTION |
| "Read-write access is applicable only when |
| static profiles as defined in ADSL Line MIB |
| [RFC2662] are implemented." |
| |
| OBJECT adslAturThreshold15MinSesL |
| MIN-ACCESS read-write |
| DESCRIPTION |
| "Read-write access is applicable only when |
| static profiles as defined in ADSL Line MIB |
| [RFC2662] are implemented." |
| |
| OBJECT adslAturThreshold15MinUasL |
| MIN-ACCESS read-write |
| DESCRIPTION |
| "Read-write access is applicable only when |
| static profiles as defined in ADSL Line MIB |
| [RFC2662] are implemented." |
| |
| OBJECT adslLineConfProfileDualLite |
| MIN-ACCESS read-only |
| DESCRIPTION |
| "Read-only access is applicable only when |
| static profiles as defined in ADSL Line MIB |
| [RFC2662] are implemented." |
| |
| |
| |
| |
| ::= { adslExtCompliances 1 } |
| |
| -- units of conformance |
| adslExtLineGroup OBJECT-GROUP |
| OBJECTS { |
| adslLineConfProfileDualLite, |
| adslLineTransAtucCap, |
| adslLineTransAtucConfig, |
| adslLineTransAtucActual, |
| adslLineGlitePowerState |
| } |
| STATUS current |
| DESCRIPTION |
| "A collection of objects providing extended |
| configuration information about an ADSL Line." |
| ::= { adslExtGroups 1 } |
| |
| adslExtAtucPhysPerfCounterGroup OBJECT-GROUP |
| OBJECTS { |
| adslAtucPerfStatFastR, |
| adslAtucPerfStatFailedFastR, |
| adslAtucPerfCurr15MinFastR, |
| adslAtucPerfCurr15MinFailedFastR, |
| adslAtucPerfCurr1DayFastR, |
| adslAtucPerfCurr1DayFailedFastR, |
| adslAtucPerfPrev1DayFastR, |
| adslAtucPerfPrev1DayFailedFastR, |
| adslAtucPerfStatSesL, |
| adslAtucPerfStatUasL, |
| adslAtucPerfCurr15MinSesL, |
| adslAtucPerfCurr15MinUasL, |
| adslAtucPerfCurr1DaySesL, |
| adslAtucPerfCurr1DayUasL, |
| adslAtucPerfPrev1DaySesL, |
| adslAtucPerfPrev1DayUasL, |
| adslAtucIntervalFastR, |
| adslAtucIntervalFailedFastR, |
| adslAtucIntervalSesL, |
| adslAtucIntervalUasL |
| } |
| STATUS current |
| DESCRIPTION |
| "A collection of objects providing raw performance |
| counts on an ADSL Line (ATU-C end)." |
| ::= { adslExtGroups 2 } |
| |
| adslExtAturPhysPerfCounterGroup OBJECT-GROUP |
| OBJECTS { |
| |
| |
| |
| adslAturPerfStatSesL, |
| adslAturPerfStatUasL, |
| adslAturPerfCurr15MinSesL, |
| adslAturPerfCurr15MinUasL, |
| adslAturPerfCurr1DaySesL, |
| adslAturPerfCurr1DayUasL, |
| adslAturPerfPrev1DaySesL, |
| adslAturPerfPrev1DayUasL, |
| adslAturIntervalSesL, adslAturIntervalUasL |
| } |
| STATUS current |
| DESCRIPTION |
| "A collection of objects providing raw performance |
| counts on an ADSL Line (ATU-C end)." |
| ::= { adslExtGroups 3 } |
| |
| adslExtLineConfProfileControlGroup OBJECT-GROUP |
| OBJECTS { |
| adslConfProfileLineType |
| } |
| STATUS current |
| DESCRIPTION |
| "A collection of objects providing profile |
| control for the ADSL system." |
| ::= { adslExtGroups 4 } |
| |
| adslExtLineAlarmConfProfileGroup OBJECT-GROUP |
| OBJECTS { |
| adslAtucThreshold15MinFailedFastR, |
| adslAtucThreshold15MinSesL, |
| adslAtucThreshold15MinUasL, |
| adslAturThreshold15MinSesL, |
| adslAturThreshold15MinUasL |
| } |
| STATUS current |
| DESCRIPTION |
| "A collection of objects providing alarm profile |
| control for the ADSL system." |
| ::= { adslExtGroups 5 } |
| |
| adslExtNotificationsGroup NOTIFICATION-GROUP |
| NOTIFICATIONS { |
| adslAtucFailedFastRThreshTrap, |
| adslAtucSesLThreshTrap, |
| adslAtucUasLThreshTrap, |
| adslAturSesLThreshTrap, |
| adslAturUasLThreshTrap |
| } |
| |
| |
| |
| STATUS current |
| DESCRIPTION |
| "The collection of ADSL extension notifications." |
| ::= { adslExtGroups 6 } |
| |
| END |