--
-- This SMIv1 module has been generated by smidump 0.4.5. Do not edit.
--
MAU-MIB DEFINITIONS ::= BEGIN
IMPORTS
IANAifJackType, IANAifMauAutoNegCapBits, IANAifMauMediaAvailable,
IANAifMauTypeListBits
FROM IANA-MAU-MIB
InterfaceIndex
FROM IF-MIB
OBJECT-TYPE
FROM RFC-1212
TRAP-TYPE
FROM RFC-1215
Counter
FROM RFC1155-SMI
mib-2
FROM RFC1213-MIB
AutonomousType, TruthValue
FROM SNMPv2-TC;
mauMod OBJECT IDENTIFIER
::= { snmpDot3MauMgt 6 }
-- mauMod MODULE-IDENTITY
-- LAST-UPDATED "200704210000Z"
-- ORGANIZATION
-- "IETF Ethernet Interfaces and Hub MIB Working Group"
-- CONTACT-INFO
-- "WG charter:
-- http://www.ietf.org/html.charters/hubmib-charter.html
--
-- Mailing Lists:
-- General Discussion: hubmib@ietf.org
-- To Subscribe: hubmib-request@ietf.org
-- In Body: subscribe your_email_address
--
--
--
-- Chair: Bert Wijnen
-- Postal: Alcatel-Lucent
-- Schagen 33
-- 3461 GL Linschoten
-- Netherlands
-- Phone: +31-348-407-775
-- EMail: bwijnen@alcatel-lucent.com
--
-- Editor: Edward Beili
-- Postal: Actelis Networks Inc.
-- 25 Bazel St., P.O.B. 10173
-- Petach-Tikva 10173
-- Israel
-- Tel: +972-3-924-3491
-- EMail: edward.beili@actelis.com"
-- DESCRIPTION
-- "Management information for 802.3 MAUs.
--
-- The following reference is used throughout this MIB module:
--
-- [IEEE802.3] refers to:
-- IEEE Std 802.3, 2005 Edition: 'IEEE Standard for Information
-- technology - Telecommunications and information exchange
-- between systems - Local and metropolitan area networks -
-- Specific requirements - Part 3: Carrier sense multiple
-- access with collision detection (CSMA/CD) access method and
-- physical layer specifications'.
--
-- Of particular interest is Clause 30, 'Management'.
--
-- Copyright (C) The IETF Trust (2007).
-- This version of this MIB module is part of RFC 4836;
-- see the RFC itself for full legal notices."
-- REVISION "200704210000Z"
-- DESCRIPTION
-- "Updated to reference IANA maintaned textual
-- conventions for MAU types, Media Availability state,
-- Auto Negotiation capabilities, and jack types,
-- instead of using internally defined values.
--
-- This version is published as RFC 4836."
-- REVISION "200309190000Z"
-- DESCRIPTION
-- "Updated to include support for 10 Gb/s MAUs.
-- This resulted in the following revisions:
-- - Added OBJECT-IDENTITY definitions for
-- 10 gigabit MAU types
--
--
--
-- - Added fiberLC jack type to JackType TC
-- - Extended ifMauTypeListBits with bits for
-- the 10 gigabit MAU types
-- - Added enumerations to ifMauMediaAvailable,
-- and updated its DESCRIPTION to reflect
-- behaviour at 10 Gb/s
-- - Added 64-bit version of ifMauFalseCarriers
-- and added mauIfGrpHCStats object group to
-- contain the new object
-- - Deprecated mauModIfCompl2 and replaced it
-- with mauModIfCompl3, which includes the new
-- object group
--
-- This version published as RFC 3636."
-- REVISION "199908240400Z"
-- DESCRIPTION
-- "This version published as RFC 2668. Updated
-- to include support for 1000 Mb/sec
-- MAUs and flow control negotiation."
-- REVISION "199710310000Z"
-- DESCRIPTION
-- "Version published as RFC 2239."
-- REVISION "199309300000Z"
-- DESCRIPTION
-- "Initial version, published as RFC 1515."
-- ::= { snmpDot3MauMgt 6 }
JackType ::=
INTEGER { other(1), rj45(2), rj45S(3), db9(4), bnc(5), fAUI(6),
mAUI(7), fiberSC(8), fiberMIC(9), fiberST(10),
telco(11), mtrj(12), hssdc(13), fiberLC(14) }
-- JackType ::= TEXTUAL-CONVENTION
-- STATUS deprecated
-- DESCRIPTION
-- "********* THIS TC IS DEPRECATED **********
--
-- This TC has been deprecated in favour of
-- IANAifJackType.
--
-- Common enumeration values for repeater
-- and interface MAU jack types."
-- SYNTAX INTEGER
-- { other(1), rj45(2), rj45S(3), db9(4), bnc(5),
-- fAUI(6), mAUI(7), fiberSC(8), fiberMIC(9),
-- fiberST(10), telco(11), mtrj(12), hssdc(13),
-- fiberLC(14) }
snmpDot3MauMgt OBJECT IDENTIFIER
::= { mib-2 26 }
snmpDot3MauTraps OBJECT IDENTIFIER
::= { snmpDot3MauMgt 0 }
dot3RpMauBasicGroup OBJECT IDENTIFIER
::= { snmpDot3MauMgt 1 }
rpMauTable OBJECT-TYPE
SYNTAX SEQUENCE OF RpMauEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Table of descriptive and status information
about the MAU(s) attached to the ports of a
repeater."
::= { dot3RpMauBasicGroup 1 }
rpMauEntry OBJECT-TYPE
SYNTAX RpMauEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the table, containing information
about a single MAU."
INDEX { rpMauGroupIndex, rpMauPortIndex, rpMauIndex }
::= { rpMauTable 1 }
RpMauEntry ::= SEQUENCE {
rpMauGroupIndex INTEGER,
rpMauPortIndex INTEGER,
rpMauIndex INTEGER,
rpMauType AutonomousType,
rpMauStatus INTEGER,
rpMauMediaAvailable IANAifMauMediaAvailable,
rpMauMediaAvailableStateExits Counter,
rpMauJabberState INTEGER,
rpMauJabberingStateEnters Counter,
rpMauFalseCarriers Counter
}
rpMauGroupIndex OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This variable uniquely identifies the group
containing the port to which the MAU described
by this entry is connected.
Note: In practice, a group will generally be
a field-replaceable unit (i.e., module, card,
or board) that can fit in the physical system
enclosure, and the group number will correspond
to a number marked on the physical enclosure.
The group denoted by a particular value of this
object is the same as the group denoted by the
same value of rptrGroupIndex."
-- REFERENCE
-- "RFC 2108, rptrGroupIndex."
::= { rpMauEntry 1 }
rpMauPortIndex OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This variable uniquely identifies the repeater
port within group rpMauGroupIndex to which the
MAU described by this entry is connected."
-- REFERENCE
-- "RFC 2108, rptrPortIndex."
::= { rpMauEntry 2 }
rpMauIndex OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This variable uniquely identifies the MAU
described by this entry from among other
MAUs connected to the same port
(rpMauPortIndex)."
-- REFERENCE
-- "[IEEE802.3], 30.5.1.1.1, aMAUID."
::= { rpMauEntry 3 }
rpMauType OBJECT-TYPE
SYNTAX AutonomousType
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object identifies the MAU type. Values for
standard IEEE 802.3 MAU types are defined in the
IANA maintained IANA-MAU-MIB module, as
OBJECT-IDENTITIES of dot3MauType.
If the MAU type is unknown, the object identifier
zeroDotZero is returned."
-- REFERENCE
-- "[IEEE802.3], 30.5.1.1.2, aMAUType."
::= { rpMauEntry 4 }
rpMauStatus OBJECT-TYPE
SYNTAX INTEGER { other(1), unknown(2), operational(3),
standby(4), shutdown(5), reset(6) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The current state of the MAU. This object MAY
be implemented as a read-only object by those
agents and MAUs that do not implement software
control of the MAU state. Some agents may not
support setting the value of this object to some
of the enumerated values.
The value other(1) is returned if the MAU is in
a state other than one of the states 2 through
6.
The value unknown(2) is returned when the MAU's
true state is unknown; for example, when it is
being initialized.
A MAU in the operational(3) state is fully
functional; it operates, and passes signals to its
attached DTE or repeater port in accordance to
its specification.
A MAU in standby(4) state forces DI and CI to
idle, and the media transmitter to idle or fault,
if supported. Standby(4) mode only applies to
link type MAUs. The state of
rpMauMediaAvailable is unaffected.
A MAU in shutdown(5) state assumes the same
condition on DI, CI, and the media transmitter,
as though it were powered down or not connected.
The MAU MAY return other(1) value for the
rpMauJabberState and rpMauMediaAvailable objects
when it is in this state. For an AUI, this
state will remove power from the AUI.
Setting this variable to the value reset(6)
resets the MAU in the same manner as a
power-off, power-on cycle of at least one-half
second would. The agent is not required to
return the value reset(6).
Setting this variable to the value
operational(3), standby(4), or shutdown(5)
causes the MAU to assume the respective state,
except that setting a mixing-type MAU or an AUI
to standby(4) will cause the MAU to enter the
shutdown state."
-- REFERENCE
-- "[IEEE802.3], 30.5.1.1.7, aMAUAdminState,
-- 30.5.1.2.2, acMAUAdminControl, and 30.5.1.2.1,
-- acResetMAU."
::= { rpMauEntry 5 }
rpMauMediaAvailable OBJECT-TYPE
SYNTAX IANAifMauMediaAvailable
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object identifies Media Available state of
the MAU, complementary to the rpMauStatus. Values
for the standard IEEE 802.3 Media Available states
are defined in the IANA maintained IANA-MAU-MIB
module, as IANAifMauMediaAvailable TC."
-- REFERENCE
-- "[IEEE802.3], 30.5.1.1.4, aMediaAvailable."
::= { rpMauEntry 6 }
rpMauMediaAvailableStateExits OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A count of the number of times that
rpMauMediaAvailable for this MAU instance leaves
the state available(3).
Discontinuities in the value of this counter can
occur at re-initialization of the management
system and at other times, as indicated by the
value of rptrMonitorPortLastChange."
-- REFERENCE
-- "[IEEE802.3], 30.5.1.1.5, aLoseMediaCounter.
-- RFC 2108, rptrMonitorPortLastChange"
::= { rpMauEntry 7 }
rpMauJabberState OBJECT-TYPE
SYNTAX INTEGER { other(1), unknown(2), noJabber(3),
jabbering(4) }
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The value other(1) is returned if the jabber
state is not 2, 3, or 4. The agent MUST always
return other(1) for MAU type dot3MauTypeAUI.
The value unknown(2) is returned when the MAU's
true state is unknown; for example, when it is
being initialized.
If the MAU is not jabbering the agent returns
noJabber(3). This is the 'normal' state.
If the MAU is in jabber state the agent returns
the jabbering(4) value."
-- REFERENCE
-- "[IEEE802.3], 30.5.1.1.6, aJabber.jabberFlag."
::= { rpMauEntry 8 }
rpMauJabberingStateEnters OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A count of the number of times that
mauJabberState for this MAU instance enters the
state jabbering(4). For MAUs of type
dot3MauTypeAUI, dot3MauType100BaseT4,
dot3MauType100BaseTX, dot3MauType100BaseFX, and
all 1000Mbps types, this counter will always
indicate zero.
Discontinuities in the value of this counter can
occur at re-initialization of the management
system and at other times, as indicated by the
value of rptrMonitorPortLastChange."
-- REFERENCE
-- "[IEEE802.3], 30.5.1.1.6, aJabber.jabberCounter.
-- RFC 2108, rptrMonitorPortLastChange"
::= { rpMauEntry 9 }
rpMauFalseCarriers OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A count of the number of false carrier events
during IDLE in 100BASE-X links. This counter
does not increment at the symbol rate. It can
increment after a valid carrier completion at a
maximum rate of once per 100 ms until the next
carrier event.
This counter increments only for MAUs of type
dot3MauType100BaseT4, dot3MauType100BaseTX,
dot3MauType100BaseFX, and all 1000Mbps types.
For all other MAU types, this counter will
always indicate zero.
The approximate minimum time for rollover of
this counter is 7.4 hours.
Discontinuities in the value of this counter can
occur at re-initialization of the management
system and at other times, as indicated by the
value of rptrMonitorPortLastChange."
-- REFERENCE
-- "[IEEE802.3], 30.5.1.1.10, aFalseCarriers.
-- RFC 2108, rptrMonitorPortLastChange"
::= { rpMauEntry 10 }
rpJackTable OBJECT-TYPE
SYNTAX SEQUENCE OF RpJackEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Information about the external jacks attached
to MAUs attached to the ports of a repeater."
::= { dot3RpMauBasicGroup 2 }
rpJackEntry OBJECT-TYPE
SYNTAX RpJackEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the table, containing information
about a particular jack."
INDEX { rpMauGroupIndex, rpMauPortIndex, rpMauIndex,
rpJackIndex }
::= { rpJackTable 1 }
RpJackEntry ::= SEQUENCE {
rpJackIndex INTEGER,
rpJackType IANAifJackType
}
rpJackIndex OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This variable uniquely identifies the jack
described by this entry from among other jacks
attached to the same MAU (rpMauIndex)."
::= { rpJackEntry 1 }
rpJackType OBJECT-TYPE
SYNTAX IANAifJackType
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The jack connector type, as it appears on the
outside of the system."
::= { rpJackEntry 2 }
dot3IfMauBasicGroup OBJECT IDENTIFIER
::= { snmpDot3MauMgt 2 }
ifMauTable OBJECT-TYPE
SYNTAX SEQUENCE OF IfMauEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Table of descriptive and status information
about MAU(s) attached to an interface."
::= { dot3IfMauBasicGroup 1 }
ifMauEntry OBJECT-TYPE
SYNTAX IfMauEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the table, containing information
about a single MAU."
INDEX { ifMauIfIndex, ifMauIndex }
::= { ifMauTable 1 }
IfMauEntry ::= SEQUENCE {
ifMauIfIndex InterfaceIndex,
ifMauIndex INTEGER,
ifMauType AutonomousType,
ifMauStatus INTEGER,
ifMauMediaAvailable IANAifMauMediaAvailable,
ifMauMediaAvailableStateExits Counter,
ifMauJabberState INTEGER,
ifMauJabberingStateEnters Counter,
ifMauFalseCarriers Counter,
ifMauTypeList INTEGER,
ifMauDefaultType AutonomousType,
ifMauAutoNegSupported TruthValue,
ifMauTypeListBits IANAifMauTypeListBits
-- ifMauHCFalseCarriers Counter64
}
ifMauIfIndex OBJECT-TYPE
SYNTAX InterfaceIndex
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This variable uniquely identifies the interface
to which the MAU described by this entry is
connected."
-- REFERENCE
-- "RFC 2863, ifIndex"
::= { ifMauEntry 1 }
ifMauIndex OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This variable uniquely identifies the MAU
described by this entry from among other MAUs
connected to the same interface (ifMauIfIndex)."
-- REFERENCE
-- "[IEEE802.3], 30.5.1.1.1, aMAUID."
::= { ifMauEntry 2 }
ifMauType OBJECT-TYPE
SYNTAX AutonomousType
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object identifies the MAU type. Values for
standard IEEE 802.3 MAU types are defined in the
IANA maintained IANA-MAU-MIB module, as
OBJECT-IDENTITIES of dot3MauType.
If the MAU type is unknown, the object identifier
zeroDotZero is returned.
This object represents the operational type of
the MAU, as determined by either 1) the result
of the auto-negotiation function or 2) if
auto-negotiation is not enabled or is not
implemented for this MAU, by the value of the
object ifMauDefaultType. In case 2), a set to
the object ifMauDefaultType will force the MAU
into the new operating mode."
-- REFERENCE
-- "[IEEE802.3], 30.5.1.1.2, aMAUType."
::= { ifMauEntry 3 }
ifMauStatus OBJECT-TYPE
SYNTAX INTEGER { other(1), unknown(2), operational(3),
standby(4), shutdown(5), reset(6) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The current state of the MAU. This object MAY
be implemented as a read-only object by those
agents and MAUs that do not implement software
control of the MAU state. Some agents may not
support setting the value of this object to some
of the enumerated values.
The value other(1) is returned if the MAU is in
a state other than one of the states 2 through
6.
The value unknown(2) is returned when the MAU's
true state is unknown; for example, when it is
being initialized.
A MAU in the operational(3) state is fully
functional; it operates, and passes signals to its
attached DTE or repeater port in accordance to
its specification.
A MAU in standby(4) state forces DI and CI to
idle and the media transmitter to idle or fault,
if supported. Standby(4) mode only applies to
link type MAUs. The state of
ifMauMediaAvailable is unaffected.
A MAU in shutdown(5) state assumes the same
condition on DI, CI, and the media transmitter,
as though it were powered down or not connected.
The MAU MAY return other(1) value for the
ifMauJabberState and ifMauMediaAvailable objects
when it is in this state. For an AUI, this
state will remove power from the AUI.
Setting this variable to the value reset(6)
resets the MAU in the same manner as a
power-off, power-on cycle of at least one-half
second would. The agent is not required to
return the value reset(6).
Setting this variable to the value
operational(3), standby(4), or shutdown(5)
causes the MAU to assume the respective state,
except that setting a mixing-type MAU or an AUI
to standby(4) will cause the MAU to enter the
shutdown state."
-- REFERENCE
-- "[IEEE802.3], 30.5.1.1.7, aMAUAdminState,
-- 30.5.1.2.2, acMAUAdminControl, and 30.5.1.2.1,
-- acResetMAU."
::= { ifMauEntry 4 }
ifMauMediaAvailable OBJECT-TYPE
SYNTAX IANAifMauMediaAvailable
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object identifies Media Available state of
the MAU, complementary to the ifMauStatus. Values
for the standard IEEE 802.3 Media Available states
are defined in the IANA maintained IANA-MAU-MIB
module, as IANAifMauMediaAvailable TC."
-- REFERENCE
-- "[IEEE802.3], 30.5.1.1.4, aMediaAvailable."
::= { ifMauEntry 5 }
ifMauMediaAvailableStateExits OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A count of the number of times that
ifMauMediaAvailable for this MAU instance leaves
the state available(3).
Discontinuities in the value of this counter can
occur at re-initialization of the management
system and at other times, as indicated by the
value of ifCounterDiscontinuityTime."
-- REFERENCE
-- "[IEEE802.3], 30.5.1.1.5, aLoseMediaCounter.
-- RFC 2863, ifCounterDiscontinuityTime."
::= { ifMauEntry 6 }
ifMauJabberState OBJECT-TYPE
SYNTAX INTEGER { other(1), unknown(2), noJabber(3),
jabbering(4) }
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The value other(1) is returned if the jabber
state is not 2, 3, or 4. The agent MUST always
return other(1) for MAU type dot3MauTypeAUI.
The value unknown(2) is returned when the MAU's
true state is unknown; for example, when it is
being initialized.
If the MAU is not jabbering the agent returns
noJabber(3). This is the 'normal' state.
If the MAU is in jabber state the agent returns
the jabbering(4) value."
-- REFERENCE
-- "[IEEE802.3], 30.5.1.1.6, aJabber.jabberFlag."
::= { ifMauEntry 7 }
ifMauJabberingStateEnters OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A count of the number of times that
mauJabberState for this MAU instance enters the
state jabbering(4). This counter will always
indicate zero for MAUs of type dot3MauTypeAUI
and those of speeds above 10Mbps.
Discontinuities in the value of this counter can
occur at re-initialization of the management
system and at other times, as indicated by the
value of ifCounterDiscontinuityTime."
-- REFERENCE
-- "[IEEE802.3], 30.5.1.1.6, aJabber.jabberCounter.
-- RFC 2863, ifCounterDiscontinuityTime."
::= { ifMauEntry 8 }
ifMauFalseCarriers OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A count of the number of false carrier events
during IDLE in 100BASE-X and 1000BASE-X links.
For all other MAU types, this counter will
always indicate zero. This counter does not
increment at the symbol rate.
It can increment after a valid carrier
completion at a maximum rate of once per 100 ms
for 100BASE-X and once per 10us for 1000BASE-X
until the next CarrierEvent.
This counter can roll over very quickly. A
management station is advised to poll the
ifMauHCFalseCarriers instead of this counter in
order to avoid loss of information.
Discontinuities in the value of this counter can
occur at re-initialization of the management
system and at other times, as indicated by the
value of ifCounterDiscontinuityTime."
-- REFERENCE
-- "[IEEE802.3], 30.5.1.1.10, aFalseCarriers.
--
--
--
-- RFC 2863, ifCounterDiscontinuityTime."
::= { ifMauEntry 9 }
ifMauTypeList OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS deprecated
DESCRIPTION
"********* THIS OBJECT IS DEPRECATED **********
This object has been deprecated in favour of
ifMauTypeListBits.
A value that uniquely identifies the set of
possible IEEE 802.3 types that the MAU could be.
The value is a sum that initially takes the
value zero. Then, for each type capability of
this MAU, 2 raised to the power noted below is
added to the sum. For example, a MAU that has
the capability to be only 10BASE-T would have a
value of 512 (2**9). In contrast, a MAU that
supports both 10Base-T (full duplex) and
100BASE-TX (full duplex) would have a value of
((2**11) + (2**16)), or 67584.
The powers of 2 assigned to the capabilities are
these:
Power Capability
0 other or unknown
1 AUI
2 10BASE-5
3 FOIRL
4 10BASE-2
5 10BASE-T duplex mode unknown
6 10BASE-FP
7 10BASE-FB
8 10BASE-FL duplex mode unknown
9 10BROAD36
10 10BASE-T half duplex mode
11 10BASE-T full duplex mode
12 10BASE-FL half duplex mode
13 10BASE-FL full duplex mode
14 100BASE-T4
15 100BASE-TX half duplex mode
16 100BASE-TX full duplex mode
17 100BASE-FX half duplex mode
18 100BASE-FX full duplex mode
19 100BASE-T2 half duplex mode
20 100BASE-T2 full duplex mode
If auto-negotiation is present on this MAU, this
object will map to ifMauAutoNegCapability."
::= { ifMauEntry 10 }
ifMauDefaultType OBJECT-TYPE
SYNTAX AutonomousType
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object identifies the default
administrative baseband MAU type to be used in
conjunction with the operational MAU type
denoted by ifMauType.
The set of possible values for this object is
the same as the set defined for the ifMauType
object.
This object represents the
administratively-configured type of the MAU. If
auto-negotiation is not enabled or is not
implemented for this MAU, the value of this
object determines the operational type of the
MAU. In this case, a set to this object will
force the MAU into the specified operating mode.
If auto-negotiation is implemented and enabled
for this MAU, the operational type of the MAU
is determined by auto-negotiation, and the value
of this object denotes the type to which the MAU
will automatically revert if/when
auto-negotiation is later disabled.
NOTE TO IMPLEMENTORS: It may be necessary to
provide for underlying hardware implementations
which do not follow the exact behavior specified
above. In particular, when
ifMauAutoNegAdminStatus transitions from enabled
to disabled, the agent implementation MUST
ensure that the operational type of the MAU (as
reported by ifMauType) correctly transitions to
the value specified by this object, rather than
continuing to operate at the value earlier
determined by the auto-negotiation function."
-- REFERENCE
-- "[IEEE802.3], 30.5.1.1.1, aMAUID, and 22.2.4.1.4."
::= { ifMauEntry 11 }
ifMauAutoNegSupported OBJECT-TYPE
SYNTAX TruthValue
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object indicates whether or not
auto-negotiation is supported on this MAU."
::= { ifMauEntry 12 }
ifMauTypeListBits OBJECT-TYPE
SYNTAX IANAifMauTypeListBits
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A value that uniquely identifies the set of
possible IEEE 802.3 types that the MAU could be.
If auto-negotiation is present on this MAU, this
object will map to ifMauAutoNegCapabilityBits.
Note that this MAU may be capable of operating
as a MAU type that is beyond the scope of this
MIB. This is indicated by returning the
bit value bOther in addition to any bit values
for standard capabilities that are listed in the
IANAifMauTypeListBits TC."
::= { ifMauEntry 13 }
-- ifMauHCFalseCarriers OBJECT-TYPE
-- SYNTAX Counter64
-- ACCESS read-only
-- STATUS mandatory
-- DESCRIPTION
-- "A count of the number of false carrier events
-- during IDLE in 100BASE-X and 1000BASE-X links.
--
-- For all other MAU types, this counter will
-- always indicate zero. This counter does not
-- increment at the symbol rate.
--
-- This counter is a 64-bit version of
-- ifMauFalseCarriers. Since the 32-bit version of
-- this counter can roll over very quickly,
-- management stations are advised to poll the
-- 64-bit version instead, in order to avoid loss
-- of information.
--
-- Discontinuities in the value of this counter can
-- occur at re-initialization of the management
-- system and at other times, as indicated by the
-- value of ifCounterDiscontinuityTime."
-- REFERENCE
-- "[IEEE802.3], 30.5.1.1.10, aFalseCarriers.
--
--
--
-- RFC 2863, ifCounterDiscontinuityTime."
-- ::= { ifMauEntry 14 }
ifJackTable OBJECT-TYPE
SYNTAX SEQUENCE OF IfJackEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Information about the external jacks attached
to MAUs attached to an interface."
::= { dot3IfMauBasicGroup 2 }
ifJackEntry OBJECT-TYPE
SYNTAX IfJackEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the table, containing information
about a particular jack."
INDEX { ifMauIfIndex, ifMauIndex, ifJackIndex }
::= { ifJackTable 1 }
IfJackEntry ::= SEQUENCE {
ifJackIndex INTEGER,
ifJackType IANAifJackType
}
ifJackIndex OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This variable uniquely identifies the jack
described by this entry from among other jacks
attached to the same MAU."
::= { ifJackEntry 1 }
ifJackType OBJECT-TYPE
SYNTAX IANAifJackType
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The jack connector type, as it appears on the
outside of the system."
::= { ifJackEntry 2 }
dot3BroadMauBasicGroup OBJECT IDENTIFIER
::= { snmpDot3MauMgt 3 }
broadMauBasicTable OBJECT-TYPE
SYNTAX SEQUENCE OF BroadMauBasicEntry
ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"********* THIS OBJECT IS DEPRECATED **********
This entire table has been deprecated. There
have been no reported implementations of this
table, and it is unlikely that there ever will
be. IEEE recommends that broadband MAU types
should not be used for new installations.
Table of descriptive and status information
about the broadband MAUs connected to
interfaces."
::= { dot3BroadMauBasicGroup 1 }
broadMauBasicEntry OBJECT-TYPE
SYNTAX BroadMauBasicEntry
ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"********* THIS OBJECT IS DEPRECATED **********
An entry in the table, containing information
about a single broadband MAU."
INDEX { broadMauIfIndex, broadMauIndex }
::= { broadMauBasicTable 1 }
BroadMauBasicEntry ::= SEQUENCE {
broadMauIfIndex InterfaceIndex,
broadMauIndex INTEGER,
broadMauXmtRcvSplitType INTEGER,
broadMauXmtCarrierFreq INTEGER,
broadMauTranslationFreq INTEGER
}
broadMauIfIndex OBJECT-TYPE
SYNTAX InterfaceIndex
ACCESS read-only
STATUS deprecated
DESCRIPTION
"********* THIS OBJECT IS DEPRECATED **********
This variable uniquely identifies the interface
to which the MAU described by this entry is
connected."
-- REFERENCE
-- "RFC 2863, ifIndex."
::= { broadMauBasicEntry 1 }
broadMauIndex OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
ACCESS read-only
STATUS deprecated
DESCRIPTION
"********* THIS OBJECT IS DEPRECATED **********
This variable uniquely identifies the MAU
connected to interface broadMauIfIndex that is
described by this entry."
-- REFERENCE
-- "[IEEE802.3], 30.5.1.1.1, aMAUID."
::= { broadMauBasicEntry 2 }
broadMauXmtRcvSplitType OBJECT-TYPE
SYNTAX INTEGER { other(1), single(2), dual(3) }
ACCESS read-only
STATUS deprecated
DESCRIPTION
"********* THIS OBJECT IS DEPRECATED **********
This object indicates the type of frequency
multiplexing/cabling system used to separate the
transmit and receive paths for the 10BROAD36
MAU.
The value other(1) is returned if the split type
is not either single or dual.
The value single(2) indicates a single cable
system. The value dual(3) indicates a dual
cable system, offset normally zero."
-- REFERENCE
-- "[IEEE802.3], 30.5.1.1.8, aBbMAUXmitRcvSplitType."
::= { broadMauBasicEntry 3 }
broadMauXmtCarrierFreq OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS deprecated
DESCRIPTION
"********* THIS OBJECT IS DEPRECATED **********
This variable indicates the transmit carrier
frequency of the 10BROAD36 MAU in MHz/4; that
is, in units of 250 kHz."
-- REFERENCE
-- "[IEEE802.3], 30.5.1.1.9,
-- aBroadbandFrequencies.xmitCarrierFrequency."
::= { broadMauBasicEntry 4 }
broadMauTranslationFreq OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS deprecated
DESCRIPTION
"********* THIS OBJECT IS DEPRECATED **********
This variable indicates the translation offset
frequency of the 10BROAD36 MAU in MHz/4; that
is, in units of 250 kHz."
-- REFERENCE
-- "[IEEE802.3], 30.5.1.1.9,
-- aBroadbandFrequencies.translationFrequency."
::= { broadMauBasicEntry 5 }
dot3IfMauAutoNegGroup OBJECT IDENTIFIER
::= { snmpDot3MauMgt 5 }
ifMauAutoNegTable OBJECT-TYPE
SYNTAX SEQUENCE OF IfMauAutoNegEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Configuration and status objects for the
auto-negotiation function of MAUs attached to
interfaces.
The ifMauAutoNegTable applies to systems in
which auto-negotiation is supported on one or
more MAUs attached to interfaces. Note that if
auto-negotiation is present and enabled, the
ifMauType object reflects the result of the
auto-negotiation function."
::= { dot3IfMauAutoNegGroup 1 }
ifMauAutoNegEntry OBJECT-TYPE
SYNTAX IfMauAutoNegEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the table, containing configuration
and status information for the auto-negotiation
function of a particular MAU."
INDEX { ifMauIfIndex, ifMauIndex }
::= { ifMauAutoNegTable 1 }
IfMauAutoNegEntry ::= SEQUENCE {
ifMauAutoNegAdminStatus INTEGER,
ifMauAutoNegRemoteSignaling INTEGER,
ifMauAutoNegConfig INTEGER,
ifMauAutoNegCapability INTEGER,
ifMauAutoNegCapAdvertised INTEGER,
ifMauAutoNegCapReceived INTEGER,
ifMauAutoNegRestart INTEGER,
ifMauAutoNegCapabilityBits IANAifMauAutoNegCapBits,
ifMauAutoNegCapAdvertisedBits IANAifMauAutoNegCapBits,
ifMauAutoNegCapReceivedBits IANAifMauAutoNegCapBits,
ifMauAutoNegRemoteFaultAdvertised INTEGER,
ifMauAutoNegRemoteFaultReceived INTEGER
}
ifMauAutoNegAdminStatus OBJECT-TYPE
SYNTAX INTEGER { enabled(1), disabled(2) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Setting this object to enabled(1) will cause
the interface that has the auto-negotiation
signaling ability to be enabled.
If the value of this object is disabled(2) then
the interface will act as it would if it had no
auto-negotiation signaling. Under these
conditions, an IEEE 802.3 MAU will immediately
be forced to the state indicated by the value of
the object ifMauDefaultType.
NOTE TO IMPLEMENTORS: When
ifMauAutoNegAdminStatus transitions from enabled
to disabled, the agent implementation MUST
ensure that the operational type of the MAU (as
reported by ifMauType) correctly transitions to
the value specified by the ifMauDefaultType
object, rather than continuing to operate at the
value earlier determined by the auto-negotiation
function."
-- REFERENCE
-- "[IEEE802.3], 30.6.1.1.2, aAutoNegAdminState,
-- and 30.6.1.2.2, acAutoNegAdminControl."
::= { ifMauAutoNegEntry 1 }
ifMauAutoNegRemoteSignaling OBJECT-TYPE
SYNTAX INTEGER { detected(1), notdetected(2) }
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A value indicating whether the remote end of
the link is using auto-negotiation signaling. It
takes the value detected(1) if and only if,
during the previous link negotiation, FLP Bursts
were received."
-- REFERENCE
-- "[IEEE802.3], 30.6.1.1.3,
-- aAutoNegRemoteSignaling."
::= { ifMauAutoNegEntry 2 }
ifMauAutoNegConfig OBJECT-TYPE
SYNTAX INTEGER { other(1), configuring(2), complete(3),
disabled(4), parallelDetectFail(5) }
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A value indicating the current status of the
auto-negotiation process. The enumeration
parallelDetectFail(5) maps to a failure in
parallel detection as defined in 28.2.3.1 of
[IEEE802.3]."
-- REFERENCE
-- "[IEEE802.3], 30.6.1.1.4, aAutoNegAutoConfig."
::= { ifMauAutoNegEntry 4 }
ifMauAutoNegCapability OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS deprecated
DESCRIPTION
"********* THIS OBJECT IS DEPRECATED **********
This object has been deprecated in favour of
ifMauAutoNegCapabilityBits.
A value that uniquely identifies the set of
capabilities of the local auto-negotiation
entity. The value is a sum that initially
takes the value zero. Then, for each capability
of this interface, 2 raised to the power noted
below is added to the sum. For example, an
interface that has the capability to support
only 100Base-TX half duplex would have a value
of 32768 (2**15). In contrast, an interface
that supports both 100Base-TX half duplex and
100Base-TX full duplex would have a value of
98304 ((2**15) + (2**16)).
The powers of 2 assigned to the capabilities are
these:
Power Capability
0 other or unknown
(1-9) (reserved)
10 10BASE-T half duplex mode
11 10BASE-T full duplex mode
12 (reserved)
13 (reserved)
14 100BASE-T4
15 100BASE-TX half duplex mode
16 100BASE-TX full duplex mode
17 (reserved)
18 (reserved)
19 100BASE-T2 half duplex mode
20 100BASE-T2 full duplex mode
Note that interfaces that support this MIB may
have capabilities that extend beyond the scope
of this MIB."
-- REFERENCE
-- "[IEEE802.3], 30.6.1.1.5,
-- aAutoNegLocalTechnologyAbility."
::= { ifMauAutoNegEntry 5 }
ifMauAutoNegCapAdvertised OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS deprecated
DESCRIPTION
"********* THIS OBJECT IS DEPRECATED **********
This object has been deprecated in favour of
ifMauAutoNegCapAdvertisedBits.
A value that uniquely identifies the set of
capabilities advertised by the local
auto-negotiation entity. Refer to
ifMauAutoNegCapability for a description of the
possible values of this object.
Capabilities in this object that are not
available in ifMauAutoNegCapability cannot be
enabled."
-- REFERENCE
-- "[IEEE802.3], 30.6.1.1.6,
-- aAutoNegAdvertisedTechnologyAbility."
::= { ifMauAutoNegEntry 6 }
ifMauAutoNegCapReceived OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS deprecated
DESCRIPTION
"********* THIS OBJECT IS DEPRECATED **********
This object has been deprecated in favour of
ifMauAutoNegCapReceivedBits.
A value that uniquely identifies the set of
capabilities received from the remote
auto-negotiation entity. Refer to
ifMauAutoNegCapability for a description of the
possible values of this object.
Note that interfaces that support this MIB may
be attached to remote auto-negotiation entities
that have capabilities beyond the scope of this
MIB."
-- REFERENCE
-- "[IEEE802.3], 30.6.1.1.7,
-- aAutoNegReceivedTechnologyAbility."
::= { ifMauAutoNegEntry 7 }
ifMauAutoNegRestart OBJECT-TYPE
SYNTAX INTEGER { restart(1), norestart(2) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"If the value of this object is set to
restart(1) then this will force auto-negotiation
to begin link renegotiation. If auto-negotiation
signaling is disabled, a write to this object
has no effect.
Setting the value of this object to norestart(2)
has no effect."
-- REFERENCE
-- "[IEEE802.3], 30.6.1.2.1,
-- acAutoNegRestartAutoConfig."
::= { ifMauAutoNegEntry 8 }
ifMauAutoNegCapabilityBits OBJECT-TYPE
SYNTAX IANAifMauAutoNegCapBits
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A value that uniquely identifies the set of
capabilities of the local auto-negotiation
entity. Note that interfaces that support this
MIB may have capabilities that extend beyond the
scope of this MIB.
Note that the local auto-negotiation entity may
support some capabilities beyond the scope of
this MIB. This is indicated by returning the
bit value bOther in addition to any bit values
for standard capabilities that are listed in the
IANAifMauAutoNegCapBits TC."
-- REFERENCE
-- "[IEEE802.3], 30.6.1.1.5,
-- aAutoNegLocalTechnologyAbility."
::= { ifMauAutoNegEntry 9 }
ifMauAutoNegCapAdvertisedBits OBJECT-TYPE
SYNTAX IANAifMauAutoNegCapBits
ACCESS read-write
STATUS mandatory
DESCRIPTION
"A value that uniquely identifies the set of
capabilities advertised by the local
auto-negotiation entity.
Capabilities in this object that are not
available in ifMauAutoNegCapabilityBits cannot
be enabled.
Note that the local auto-negotiation entity may
advertise some capabilities beyond the scope of
this MIB. This is indicated by returning the
bit value bOther in addition to any bit values
for standard capabilities that are listed in the
IANAifMauAutoNegCapBits TC."
-- REFERENCE
-- "[IEEE802.3], 30.6.1.1.6,
-- aAutoNegAdvertisedTechnologyAbility."
::= { ifMauAutoNegEntry 10 }
ifMauAutoNegCapReceivedBits OBJECT-TYPE
SYNTAX IANAifMauAutoNegCapBits
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A value that uniquely identifies the set of
capabilities received from the remote
auto-negotiation entity.
Note that interfaces that support this MIB may
be attached to remote auto-negotiation entities
that have capabilities beyond the scope of this
MIB. This is indicated by returning the bit
value bOther in addition to any bit values for
standard capabilities that are listed in the
IANAifMauAutoNegCapBits TC."
-- REFERENCE
-- "[IEEE802.3], 30.6.1.1.7,
-- aAutoNegReceivedTechnologyAbility."
::= { ifMauAutoNegEntry 11 }
ifMauAutoNegRemoteFaultAdvertised OBJECT-TYPE
SYNTAX INTEGER { noError(1), offline(2), linkFailure(3),
autoNegError(4) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"A value that identifies any local fault
indications that this MAU has detected and will
advertise at the next auto-negotiation
interaction for 1000Mbps MAUs."
-- REFERENCE
-- "[IEEE802.3], 30.6.1.1.6,
-- aAutoNegAdvertisedTechnologyAbility."
::= { ifMauAutoNegEntry 12 }
ifMauAutoNegRemoteFaultReceived OBJECT-TYPE
SYNTAX INTEGER { noError(1), offline(2), linkFailure(3),
autoNegError(4) }
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A value that identifies any fault indications
received from the far end of a link by the
local auto-negotiation entity for 1000Mbps
MAUs."
-- REFERENCE
-- "[IEEE802.3], 30.6.1.1.7,
-- aAutoNegReceivedTechnologyAbility."
::= { ifMauAutoNegEntry 13 }
mauModConf OBJECT IDENTIFIER
::= { mauMod 1 }
mauModCompls OBJECT IDENTIFIER
::= { mauModConf 1 }
mauModObjGrps OBJECT IDENTIFIER
::= { mauModConf 2 }
mauModNotGrps OBJECT IDENTIFIER
::= { mauModConf 3 }
rpMauJabberTrap TRAP-TYPE
ENTERPRISE snmpDot3MauMgt
VARIABLES { rpMauJabberState }
-- STATUS mandatory
DESCRIPTION
"This trap is sent whenever a managed repeater
MAU enters the jabber state.
The agent MUST throttle the generation of
consecutive rpMauJabberTraps so that there is at
least a five-second gap between them."
-- REFERENCE
-- "[IEEE802.3], 30.5.1.3.1, nJabber notification."
::= 1
ifMauJabberTrap TRAP-TYPE
ENTERPRISE snmpDot3MauMgt
VARIABLES { ifMauJabberState }
-- STATUS mandatory
DESCRIPTION
"This trap is sent whenever a managed interface
MAU enters the jabber state.
The agent MUST throttle the generation of
consecutive ifMauJabberTraps so that there is at
least a five-second gap between them."
-- REFERENCE
-- "[IEEE802.3], 30.5.1.3.1, nJabber notification."
::= 2
mauRpGrpBasic OBJECT IDENTIFIER
::= { mauModObjGrps 1 }
-- mauRpGrpBasic OBJECT-GROUP
-- OBJECTS { rpMauGroupIndex, rpMauPortIndex, rpMauIndex,
-- rpMauType, rpMauStatus, rpMauMediaAvailable,
-- rpMauMediaAvailableStateExits, rpMauJabberState,
-- rpMauJabberingStateEnters }
-- STATUS mandatory
-- DESCRIPTION
-- "Basic conformance group for MAUs attached to
-- repeater ports. This group is also the
-- conformance specification for RFC 1515
-- implementations."
-- ::= { mauModObjGrps 1 }
mauRpGrp100Mbs OBJECT IDENTIFIER
::= { mauModObjGrps 2 }
-- mauRpGrp100Mbs OBJECT-GROUP
-- OBJECTS { rpMauFalseCarriers }
-- STATUS mandatory
-- DESCRIPTION
-- "Conformance group for MAUs attached to
-- repeater ports with 100 Mb/s or greater
-- capability."
-- ::= { mauModObjGrps 2 }
mauRpGrpJack OBJECT IDENTIFIER
::= { mauModObjGrps 3 }
-- mauRpGrpJack OBJECT-GROUP
-- OBJECTS { rpJackType }
-- STATUS mandatory
-- DESCRIPTION
-- "Conformance group for MAUs attached to
-- repeater ports with managed jacks."
-- ::= { mauModObjGrps 3 }
mauIfGrpBasic OBJECT IDENTIFIER
::= { mauModObjGrps 4 }
-- mauIfGrpBasic OBJECT-GROUP
-- OBJECTS { ifMauIfIndex, ifMauIndex, ifMauType, ifMauStatus,
-- ifMauMediaAvailable, ifMauMediaAvailableStateExits,
-- ifMauJabberState, ifMauJabberingStateEnters }
-- STATUS mandatory
-- DESCRIPTION
-- "Basic conformance group for MAUs attached to
-- interfaces. This group also provides a
-- conformance specification for RFC 1515
-- implementations."
-- ::= { mauModObjGrps 4 }
mauIfGrp100Mbs OBJECT IDENTIFIER
::= { mauModObjGrps 5 }
-- mauIfGrp100Mbs OBJECT-GROUP
-- OBJECTS { ifMauFalseCarriers, ifMauTypeList, ifMauDefaultType,
-- ifMauAutoNegSupported }
-- STATUS deprecated
-- DESCRIPTION
-- "********* THIS GROUP IS DEPRECATED **********
--
-- Conformance group for MAUs attached to
-- interfaces with 100 Mb/s capability.
--
-- This object group has been deprecated in favor
-- of mauIfGrpHighCapacity."
-- ::= { mauModObjGrps 5 }
mauIfGrpJack OBJECT IDENTIFIER
::= { mauModObjGrps 6 }
-- mauIfGrpJack OBJECT-GROUP
-- OBJECTS { ifJackType }
-- STATUS mandatory
-- DESCRIPTION
-- "Conformance group for MAUs attached to
-- interfaces with managed jacks."
-- ::= { mauModObjGrps 6 }
mauIfGrpAutoNeg OBJECT IDENTIFIER
::= { mauModObjGrps 7 }
-- mauIfGrpAutoNeg OBJECT-GROUP
-- OBJECTS { ifMauAutoNegAdminStatus,
-- ifMauAutoNegRemoteSignaling, ifMauAutoNegConfig,
-- ifMauAutoNegCapability, ifMauAutoNegCapAdvertised,
-- ifMauAutoNegCapReceived, ifMauAutoNegRestart }
-- STATUS deprecated
-- DESCRIPTION
-- "********* THIS GROUP IS DEPRECATED **********
--
-- Conformance group for MAUs attached to
-- interfaces with managed auto-negotiation.
--
-- This object group has been deprecated in favor
-- of mauIfGrpAutoNeg2."
-- ::= { mauModObjGrps 7 }
mauBroadBasic OBJECT IDENTIFIER
::= { mauModObjGrps 8 }
-- mauBroadBasic OBJECT-GROUP
-- OBJECTS { broadMauIfIndex, broadMauIndex,
-- broadMauXmtRcvSplitType, broadMauXmtCarrierFreq,
-- broadMauTranslationFreq }
-- STATUS deprecated
-- DESCRIPTION
-- "********* THIS GROUP IS DEPRECATED **********
-- Conformance group for broadband MAUs attached
-- to interfaces.
--
-- This object group is deprecated. There have
-- been no reported implementations of this group,
-- and it was felt to be unlikely that there will
-- be any future implementations."
-- ::= { mauModObjGrps 8 }
mauIfGrpHighCapacity OBJECT IDENTIFIER
::= { mauModObjGrps 9 }
-- mauIfGrpHighCapacity OBJECT-GROUP
-- OBJECTS { ifMauFalseCarriers, ifMauTypeListBits,
-- ifMauDefaultType, ifMauAutoNegSupported }
-- STATUS mandatory
-- DESCRIPTION
-- "Conformance group for MAUs attached to
-- interfaces with 100 Mb/s or greater capability."
-- ::= { mauModObjGrps 9 }
mauIfGrpAutoNeg2 OBJECT IDENTIFIER
::= { mauModObjGrps 10 }
-- mauIfGrpAutoNeg2 OBJECT-GROUP
-- OBJECTS { ifMauAutoNegAdminStatus,
-- ifMauAutoNegRemoteSignaling, ifMauAutoNegConfig,
-- ifMauAutoNegCapabilityBits,
-- ifMauAutoNegCapAdvertisedBits,
-- ifMauAutoNegCapReceivedBits, ifMauAutoNegRestart }
-- STATUS mandatory
-- DESCRIPTION
-- "Conformance group for MAUs attached to
-- interfaces with managed auto-negotiation."
-- ::= { mauModObjGrps 10 }
mauIfGrpAutoNeg1000Mbps OBJECT IDENTIFIER
::= { mauModObjGrps 11 }
-- mauIfGrpAutoNeg1000Mbps OBJECT-GROUP
-- OBJECTS { ifMauAutoNegRemoteFaultAdvertised,
-- ifMauAutoNegRemoteFaultReceived }
-- STATUS mandatory
-- DESCRIPTION
-- "Conformance group for 1000Mbps MAUs attached to
-- interfaces with managed auto-negotiation."
-- ::= { mauModObjGrps 11 }
mauIfGrpHCStats OBJECT IDENTIFIER
::= { mauModObjGrps 12 }
-- mauIfGrpHCStats OBJECT-GROUP
-- OBJECTS { ifMauHCFalseCarriers }
-- STATUS mandatory
-- DESCRIPTION
-- "Conformance for high capacity statistics for
-- MAUs attached to interfaces."
-- ::= { mauModObjGrps 12 }
rpMauNotifications OBJECT IDENTIFIER
::= { mauModNotGrps 1 }
-- rpMauNotifications NOTIFICATION-GROUP
-- NOTIFICATIONS { rpMauJabberTrap }
-- STATUS mandatory
-- DESCRIPTION
-- "Notifications for repeater MAUs."
-- ::= { mauModNotGrps 1 }
ifMauNotifications OBJECT IDENTIFIER
::= { mauModNotGrps 2 }
-- ifMauNotifications NOTIFICATION-GROUP
-- NOTIFICATIONS { ifMauJabberTrap }
-- STATUS mandatory
-- DESCRIPTION
-- "Notifications for interface MAUs."
-- ::= { mauModNotGrps 2 }
mauModRpCompl OBJECT IDENTIFIER
::= { mauModCompls 1 }
-- mauModRpCompl MODULE-COMPLIANCE
-- STATUS deprecated
-- DESCRIPTION
-- "******** THIS COMPLIANCE IS DEPRECATED ********
-- Compliance for MAUs attached to repeater
-- ports.
--
-- This compliance is deprecated and replaced by
-- mauModRpCompl2, which corrects an oversight by
-- allowing rpMauStatus to be implemented
-- read-only."
-- MODULE -- -- this module
-- MANDATORY-GROUPS { mauRpGrpBasic }
-- GROUP mauRpGrp100Mbs
-- DESCRIPTION
-- "Implementation of this optional group is
-- recommended for MAUs that have 100Mb/s or
-- greater capability."
-- GROUP mauRpGrpJack
-- DESCRIPTION
-- "Implementation of this optional group is
-- recommended for MAUs that have one or more
-- external jacks."
-- GROUP rpMauNotifications
-- DESCRIPTION
-- "Implementation of this group is recommended
-- for MAUs attached to repeater ports."
-- ::= { mauModCompls 1 }
mauModIfCompl OBJECT IDENTIFIER
::= { mauModCompls 2 }
-- mauModIfCompl MODULE-COMPLIANCE
-- STATUS deprecated
-- DESCRIPTION
-- "******** THIS COMPLIANCE IS DEPRECATED ********
--
-- Compliance for MAUs attached to interfaces.
-- This compliance is deprecated and replaced by
-- mauModIfCompl2."
-- MODULE -- -- this module
-- MANDATORY-GROUPS { mauIfGrpBasic }
-- GROUP mauIfGrp100Mbs
-- DESCRIPTION
-- "Implementation of this optional group is
-- recommended for MAUs that have 100Mb/s
-- capability."
-- GROUP mauIfGrpJack
-- DESCRIPTION
-- "Implementation of this optional group is
-- recommended for MAUs that have one or more
-- external jacks."
-- GROUP mauIfGrpAutoNeg
-- DESCRIPTION
-- "Implementation of this group is mandatory
-- for MAUs that support managed
-- auto-negotiation."
-- GROUP mauBroadBasic
-- DESCRIPTION
-- "Implementation of this group is mandatory
-- for broadband MAUs."
-- GROUP ifMauNotifications
-- DESCRIPTION
-- "Implementation of this group is recommended
-- for MAUs attached to interfaces."
-- ::= { mauModCompls 2 }
mauModIfCompl2 OBJECT IDENTIFIER
::= { mauModCompls 3 }
-- mauModIfCompl2 MODULE-COMPLIANCE
-- STATUS deprecated
-- DESCRIPTION
-- "******** THIS COMPLIANCE IS DEPRECATED ********
--
-- Compliance for MAUs attached to interfaces.
--
-- This compliance is deprecated and replaced by
-- mauModIfCompl3."
-- MODULE -- -- this module
-- MANDATORY-GROUPS { mauIfGrpBasic }
-- GROUP mauIfGrpHighCapacity
-- DESCRIPTION
-- "Implementation of this optional group is
-- recommended for MAUs that have 100Mb/s
-- or greater capability."
-- GROUP mauIfGrpJack
-- DESCRIPTION
-- "Implementation of this optional group is
-- recommended for MAUs that have one or more
-- external jacks."
-- GROUP mauIfGrpAutoNeg2
-- DESCRIPTION
-- "Implementation of this group is mandatory
-- for MAUs that support managed
-- auto-negotiation."
-- GROUP mauIfGrpAutoNeg1000Mbps
-- DESCRIPTION
-- "Implementation of this group is mandatory
-- for MAUs that have 1000Mb/s or greater
-- capability and support managed
-- auto-negotiation."
-- GROUP ifMauNotifications
-- DESCRIPTION
-- "Implementation of this group is recommended
-- for MAUs attached to interfaces."
-- OBJECT ifMauStatus
-- MIN-ACCESS read-only
-- DESCRIPTION
-- "Write access is not required."
-- ::= { mauModCompls 3 }
mauModRpCompl2 OBJECT IDENTIFIER
::= { mauModCompls 4 }
-- mauModRpCompl2 MODULE-COMPLIANCE
-- STATUS mandatory
-- DESCRIPTION
-- "Compliance for MAUs attached to repeater
-- ports.
--
-- Note that compliance with this compliance
-- statement requires compliance with the
-- snmpRptrModCompl MODULE-COMPLIANCE statement of
-- the SNMP-REPEATER-MIB (RFC 2108)."
-- MODULE -- -- this module
-- MANDATORY-GROUPS { mauRpGrpBasic }
-- GROUP mauRpGrp100Mbs
-- DESCRIPTION
-- "Implementation of this optional group is
-- recommended for MAUs that have 100Mb/s or
-- greater capability."
-- GROUP mauRpGrpJack
-- DESCRIPTION
-- "Implementation of this optional group is
-- recommended for MAUs that have one or more
-- external jacks."
-- GROUP rpMauNotifications
-- DESCRIPTION
-- "Implementation of this group is recommended
-- for MAUs attached to repeater ports."
-- OBJECT rpMauStatus
-- MIN-ACCESS read-only
-- DESCRIPTION
-- "Write access is not required."
-- ::= { mauModCompls 4 }
mauModIfCompl3 OBJECT IDENTIFIER
::= { mauModCompls 5 }
-- mauModIfCompl3 MODULE-COMPLIANCE
-- STATUS mandatory
-- DESCRIPTION
-- "Compliance for MAUs attached to interfaces.
--
-- Note that compliance with this compliance
-- statement requires compliance with the
-- ifCompliance3 MODULE-COMPLIANCE statement of the
-- IF-MIB (RFC 2863) and the dot3Compliance2
-- MODULE-COMPLIANCE statement of the
-- EtherLike-MIB (RFC3635)."
-- MODULE -- -- this module
-- MANDATORY-GROUPS { mauIfGrpBasic }
-- GROUP mauIfGrpHighCapacity
-- DESCRIPTION
-- "Implementation of this optional group is
-- recommended for MAUs that have 100Mb/s
-- or greater capability."
-- GROUP mauIfGrpHCStats
-- DESCRIPTION
-- "Implementation of this group is mandatory
-- for MAUs that have 1000Mb/s capacity, and
-- is recommended for MAUs that have 100Mb/s
-- capacity."
-- GROUP mauIfGrpJack
-- DESCRIPTION
-- "Implementation of this optional group is
-- recommended for MAUs that have one or more
-- external jacks."
-- GROUP mauIfGrpAutoNeg2
-- DESCRIPTION
-- "Implementation of this group is mandatory
-- for MAUs that support managed
-- auto-negotiation."
-- GROUP mauIfGrpAutoNeg1000Mbps
-- DESCRIPTION
-- "Implementation of this group is mandatory
-- for MAUs that have 1000Mb/s or greater
-- capability and support managed
-- auto-negotiation."
-- GROUP ifMauNotifications
-- DESCRIPTION
-- "Implementation of this group is recommended
-- for MAUs attached to interfaces."
-- OBJECT ifMauStatus
-- MIN-ACCESS read-only
-- DESCRIPTION
-- "Write access is not required."
-- ::= { mauModCompls 5 }
END -- end of module MAU-MIB.