VRRPV3-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE,
NOTIFICATION-TYPE, Counter32,
Integer32, mib-2, Unsigned32,
Counter64, TimeTicks
FROM SNMPv2-SMI -- RFC2578
TEXTUAL-CONVENTION, RowStatus,
MacAddress, TruthValue, TimeStamp,
TimeInterval
FROM SNMPv2-TC -- RFC2579
MODULE-COMPLIANCE, OBJECT-GROUP,
NOTIFICATION-GROUP
FROM SNMPv2-CONF -- RFC2580
ifIndex
FROM IF-MIB -- RFC2863
InetAddressType, InetAddress
FROM INET-ADDRESS-MIB; -- RFC4001
vrrpv3MIB MODULE-IDENTITY
LAST-UPDATED "201708140000Z" -- Aug 14, 2017
ORGANIZATION "IETF VRRP Working Group"
CONTACT-INFO
"WG E-Mail: vrrp@ietf.org
Editor: Kalyan Tata
Nokia
313 Fairchild Dr,
Mountain View, CA 94043
Tata_kalyan@yahoo.com"
DESCRIPTION
"This MIB describes objects used for managing Virtual
Router Redundancy Protocol version 3 (VRRPv3).
Copyright (c) 2012 IETF Trust and the persons
identified as authors of the code. All rights
reserved.
Redistribution and use in source and binary forms,
with or without modification, is permitted pursuant
to, and subject to the license terms contained in,
the Simplified BSD License set forth in Section
4.c of the IETF Trust's Legal Provisions Relating
to IETF Documents
(http://trustee.ietf.org/license-info).
This version of the MIB module is part of RFC 6527.
Please see the RFC for full legal notices."
REVISION "201708140000Z" -- Aug 14, 2017
DESCRIPTION "Apply RFC 6527 errata id 4168 and 5086."
REVISION "201202130000Z" -- Feb 13, 2012
DESCRIPTION "Initial version as published in RFC 6527."
::= { mib-2 207 }
-- Textual Conventions
Vrrpv3VrIdTC ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS current
DESCRIPTION
"The value of the Virtual Router Identifier noted as
(VRID) in RFC 5798. This, along with interface index
(ifIndex) and IP version, serves to uniquely identify
a virtual router on a given VRRP router."
REFERENCE "RFC 5798 (Sections 3 and 5.2.3)"
SYNTAX Integer32 (1..255)
-- VRRPv3 MIB Groups
vrrpv3Notifications OBJECT IDENTIFIER ::= { vrrpv3MIB 0 }
vrrpv3Objects OBJECT IDENTIFIER ::= { vrrpv3MIB 1 }
vrrpv3Conformance OBJECT IDENTIFIER ::= { vrrpv3MIB 2 }
-- VRRPv3 MIB Objects
vrrpv3Operations OBJECT IDENTIFIER ::= { vrrpv3Objects 1 }
vrrpv3Statistics OBJECT IDENTIFIER ::= { vrrpv3Objects 2 }
-- VRRPv3 Operations Table
vrrpv3OperationsTable OBJECT-TYPE
SYNTAX SEQUENCE OF Vrrpv3OperationsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Unified Operations table for a VRRP router that
consists of a sequence (i.e., one or more conceptual
rows) of 'vrrpv3OperationsEntry' items each of which
describe the operational characteristics of a virtual
router."
::= { vrrpv3Operations 1 }
vrrpv3OperationsEntry OBJECT-TYPE
SYNTAX Vrrpv3OperationsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the vrrpv3OperationsTable containing the
operational characteristics of a virtual router.
On a VRRP router, a given virtual router is
identified by a combination of ifIndex, VRID, and
the IP version. ifIndex represents an interface of
the router.
A row must be created with vrrpv3OperationsStatus
set to initialize(1) and cannot transition to
backup(2) or master(3) until
vrrpv3OperationsRowStatus is transitioned to
active(1).
The information in this table is persistent and when
written the entity SHOULD save the change to non-
volatile storage."
INDEX { ifIndex, vrrpv3OperationsVrId,
vrrpv3OperationsInetAddrType
}
::= { vrrpv3OperationsTable 1 }
Vrrpv3OperationsEntry ::=
SEQUENCE {
vrrpv3OperationsVrId
Vrrpv3VrIdTC,
vrrpv3OperationsInetAddrType
InetAddressType,
vrrpv3OperationsMasterIpAddr
InetAddress,
vrrpv3OperationsPrimaryIpAddr
InetAddress,
vrrpv3OperationsVirtualMacAddr
MacAddress,
vrrpv3OperationsStatus
INTEGER,
vrrpv3OperationsPriority
Unsigned32,
vrrpv3OperationsAddrCount
Integer32,
vrrpv3OperationsAdvInterval
TimeInterval,
vrrpv3OperationsPreemptMode
TruthValue,
vrrpv3OperationsAcceptMode
TruthValue,
vrrpv3OperationsUpTime
TimeTicks,
vrrpv3OperationsRowStatus
RowStatus
}
vrrpv3OperationsVrId OBJECT-TYPE
SYNTAX Vrrpv3VrIdTC
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object contains the Virtual Router Identifier
(VRID)."
REFERENCE "RFC 4001"
::= { vrrpv3OperationsEntry 1 }
vrrpv3OperationsInetAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The IP address type of Vrrpv3OperationsEntry and
Vrrpv3AssociatedIpAddrEntry. This value determines
the type for vrrpv3OperationsMasterIpAddr,
vrrpv3OperationsPrimaryIpAddr, and
vrrpv3AssociatedIpAddrAddress.
ipv4(1) and ipv6(2) are the only two values supported
in this MIB module."
REFERENCE "RFC 4001"
::= { vrrpv3OperationsEntry 2 }
vrrpv3OperationsMasterIpAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The master router's real IP address. The master router
would set this address to vrrpv3OperationsPrimaryIpAddr
while transitioning to master state. For backup
routers, this is the IP address listed as the source in
the VRRP advertisement last received by this virtual
router."
REFERENCE "RFC 5798"
::= { vrrpv3OperationsEntry 3 }
vrrpv3OperationsPrimaryIpAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"In the case where there is more than one IP
Address (associated IP addresses) for a given
'ifIndex', this object is used to specify the IP
address that will become the
vrrpv3OperationsMasterIpAddr', should the virtual
router transition from backup state to master."
::= { vrrpv3OperationsEntry 4 }
vrrpv3OperationsVirtualMacAddr OBJECT-TYPE
SYNTAX MacAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The virtual MAC address of the virtual router.
Although this object can be derived from the
'vrrpv3OperationsVrId' object, it is defined so that it
is easily obtainable by a management application and
can be included in VRRP-related SNMP notifications."
::= { vrrpv3OperationsEntry 5 }
vrrpv3OperationsStatus OBJECT-TYPE
SYNTAX INTEGER {
initialize(1),
backup(2),
master(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current state of the virtual router. This object
has three defined values:
- 'initialize', which indicates that the
virtual router is waiting for a startup event.
- 'backup', which indicates that the virtual router is
monitoring the availability of the master router.
- 'master', which indicates that the virtual router
is forwarding packets for IP addresses that are
associated with this router."
REFERENCE "RFC 5798"
::= { vrrpv3OperationsEntry 6 }
vrrpv3OperationsPriority OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the priority to be used for the
virtual router master election process; higher values
imply higher priority.
A priority of '0', although not settable, is sent by
the master router to indicate that this router has
ceased to participate in VRRP, and a backup virtual
router should transition to become a new master.
A priority of 255 is used for the router that owns the
associated IP address(es) for VRRP over IPv4 and hence
is not settable.
Setting the values of this object to 0 or 255 should be
rejected by the agents implementing this MIB module.
For example, an SNMP agent would return 'badValue(3)'
when a user tries to set the values 0 or 255 for this
object."
REFERENCE "RFC 5798, Section 6.1"
DEFVAL { 100 }
::= { vrrpv3OperationsEntry 7 }
vrrpv3OperationsAddrCount OBJECT-TYPE
SYNTAX Integer32 (0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of IP addresses that are associated with
this virtual router. This number is equal to the
number of rows in the vrrpv3AssociatedAddrTable that
correspond to a given ifIndex/VRID/IP version."
REFERENCE "RFC 5798, Section 6.1"
::= { vrrpv3OperationsEntry 8 }
vrrpv3OperationsAdvInterval OBJECT-TYPE
SYNTAX TimeInterval (1..4095)
UNITS "centiseconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The time interval, in centiseconds, between sending
advertisement messages. Only the master router sends
VRRP advertisements."
REFERENCE "RFC 5798, Section 6.1"
DEFVAL { 100}
::= { vrrpv3OperationsEntry 9 }
vrrpv3OperationsPreemptMode OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Controls whether a higher priority virtual router will
preempt a lower priority master."
REFERENCE "RFC 5798, Section 6.1"
DEFVAL { true }
::= { vrrpv3OperationsEntry 10 }
vrrpv3OperationsAcceptMode OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Controls whether a virtual router in master state
will accept packets addressed to the address owner's
address as its own if it is not the address
owner. Default is false(2)."
DEFVAL { false }
::= { vrrpv3OperationsEntry 11 }
vrrpv3OperationsUpTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This value represents the amount of time, in
TimeTicks (hundredth of a second), since this virtual
router (i.e., the 'vrrpv3OperationsStatus')
transitioned out of 'initialize'."
REFERENCE "RFC 5798, Section 6.1"
::= { vrrpv3OperationsEntry 12 }
vrrpv3OperationsRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The RowStatus variable should be used in accordance to
installation and removal conventions for conceptual
rows.
To create a row in this table, a manager sets this
object to either createAndGo(4) or createAndWait(5).
Until instances of all corresponding columns are
appropriately configured, the value of the
corresponding instance of the
'vrrpv3OperationsRowStatus' column will be read as
notReady(3).
In particular, a newly created row cannot be made
active(1) until (minimally) the corresponding instance
of vrrpv3OperationsInetAddrType, vrrpv3OperationsVrId,
and vrrpv3OperationsPrimaryIpAddr has been set, and
there is at least one active row in the
'vrrpv3AssociatedIpAddrTable' defining an associated
IP address.
notInService(2) should be used to administratively
bring the row down.
A typical order of operation to add a row is:
1. Create a row in vrrpv3OperationsTable with
createAndWait(5).
2. Create one or more corresponding rows in
vrrpv3AssociatedIpAddrTable.
3. Populate the vrrpv3OperationsEntry.
4. Set vrrpv3OperationsRowStatus to active(1).
A typical order of operation to delete an entry is:
1. Set vrrpv3OperationsRowStatus to notInService(2).
2. Set the corresponding rows in
vrrpv3AssociatedIpAddrTable to destroy(6) to delete
the entry.
3. Set vrrpv3OperationsRowStatus to destroy(6) to
delete the entry."
::= { vrrpv3OperationsEntry 13 }
-- VRRP Associated Address Table
vrrpv3AssociatedIpAddrTable OBJECT-TYPE
SYNTAX SEQUENCE OF Vrrpv3AssociatedIpAddrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table of addresses associated with each virtual
router."
::= { vrrpv3Operations 2 }
vrrpv3AssociatedIpAddrEntry OBJECT-TYPE
SYNTAX Vrrpv3AssociatedIpAddrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the table contains an IP address that is
associated with a virtual router. The number of rows
for a given IP version, VrID, and ifIndex will equal
the number of IP addresses associated (e.g., backed up)
by the virtual router (equivalent to
'vrrpv3OperationsIpAddrCount').
Rows in the table cannot be modified unless the value
of 'vrrpv3OperationsStatus' for the corresponding entry
in the vrrpv3OperationsTable has transitioned to
initialize(1).
The information in this table is persistent and when
written the entity SHOULD save the change to non-
volatile storage."
INDEX { ifIndex, vrrpv3OperationsVrId,
vrrpv3OperationsInetAddrType,
vrrpv3AssociatedIpAddrAddress }
::= { vrrpv3AssociatedIpAddrTable 1 }
Vrrpv3AssociatedIpAddrEntry ::=
SEQUENCE {
vrrpv3AssociatedIpAddrAddress
InetAddress,
vrrpv3AssociatedIpAddrRowStatus
RowStatus
}
vrrpv3AssociatedIpAddrAddress OBJECT-TYPE
SYNTAX InetAddress (SIZE (0|4|16))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The assigned IP addresses that a virtual router is
responsible for backing up.
The IP address type is determined by the value of
vrrpv3OperationsInetAddrType in the index of this
row."
REFERENCE "RFC 5798"
::= { vrrpv3AssociatedIpAddrEntry 1 }
vrrpv3AssociatedIpAddrRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The row status variable, used according to
installation and removal conventions for conceptual
rows. To create a row in this table, a manager sets
this object to either createAndGo(4) or
createAndWait(5). Setting this object to active(1)
results in the addition of an associated address for a
virtual router. Setting this object to notInService(2)
results in administratively bringing down the row.
Destroying the entry or setting it to destroy(6)
removes the associated address from the virtual router.
The use of other values is implementation-dependent.
Implementations should not allow deletion of the last
row corresponding to an active row in
vrrpv3OperationsTable.
Refer to the description of vrrpv3OperationsRowStatus
for typical row creation and deletion scenarios."
::= { vrrpv3AssociatedIpAddrEntry 2 }
-- VRRP Router Statistics
vrrpv3RouterChecksumErrors OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of VRRP packets received with an
invalid VRRP checksum value.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
vrrpv3GlobalStatisticsDiscontinuityTime."
REFERENCE "RFC 5798, Section 5.2.8"
::= { vrrpv3Statistics 1 }
vrrpv3RouterVersionErrors OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of VRRP packets received with an
unknown or unsupported version number.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
vrrpv3GlobalStatisticsDiscontinuityTime."
REFERENCE "RFC 5798, Section 5.2.1"
::= { vrrpv3Statistics 2 }
vrrpv3RouterVrIdErrors OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of VRRP packets received with a
VRID that is not valid for any virtual router on this
router.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
vrrpv3GlobalStatisticsDiscontinuityTime."
REFERENCE "RFC 5798, Section 5.2.3"
::= { vrrpv3Statistics 3 }
vrrpv3GlobalStatisticsDiscontinuityTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime on the most recent occasion at
which one of vrrpv3RouterChecksumErrors,
vrrpv3RouterVersionErrors, and vrrpv3RouterVrIdErrors
suffered a discontinuity.
If no such discontinuities have occurred since the last
re-initialization of the local management subsystem,
then this object contains a zero value."
::= { vrrpv3Statistics 4 }
-- VRRP Router Statistics Table
vrrpv3StatisticsTable OBJECT-TYPE
SYNTAX SEQUENCE OF Vrrpv3StatisticsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table of virtual router statistics."
::= { vrrpv3Statistics 5 }
vrrpv3StatisticsEntry OBJECT-TYPE
SYNTAX Vrrpv3StatisticsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the table containing statistics
information about a given virtual router."
AUGMENTS { vrrpv3OperationsEntry }
::= { vrrpv3StatisticsTable 1 }
Vrrpv3StatisticsEntry ::=
SEQUENCE {
vrrpv3StatisticsMasterTransitions
Counter32,
vrrpv3StatisticsNewMasterReason
INTEGER,
vrrpv3StatisticsRcvdAdvertisements
Counter64,
vrrpv3StatisticsAdvIntervalErrors
Counter64,
vrrpv3StatisticsIpTtlErrors
Counter64,
vrrpv3StatisticsProtoErrReason
INTEGER,
vrrpv3StatisticsRcvdPriZeroPackets
Counter64,
vrrpv3StatisticsSentPriZeroPackets
Counter64,
vrrpv3StatisticsRcvdInvalidTypePackets
Counter64,
vrrpv3StatisticsAddressListErrors
Counter64,
vrrpv3StatisticsPacketLengthErrors
Counter64,
vrrpv3StatisticsRowDiscontinuityTime
TimeStamp,
vrrpv3StatisticsRefreshRate
Unsigned32
}
vrrpv3StatisticsMasterTransitions OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of times that this virtual router's
state has transitioned to master state.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
vrrpv3StatisticsRowDiscontinuityTime."
::= { vrrpv3StatisticsEntry 1 }
vrrpv3StatisticsNewMasterReason OBJECT-TYPE
SYNTAX INTEGER {
notMaster (0),
priority (1),
preempted (2),
masterNoResponse (3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This indicates the reason for the virtual router to
transition to master state. If the virtual router
never transitioned to master state, the value of this
object is notMaster(0). Otherwise, this indicates the
reason this virtual router transitioned to master
state the last time. Used by vrrpv3NewMaster
notification."
::= { vrrpv3StatisticsEntry 2 }
vrrpv3StatisticsRcvdAdvertisements OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of VRRP advertisements received by
this virtual router.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
vrrpv3StatisticsRowDiscontinuityTime."
::= { vrrpv3StatisticsEntry 3 }
vrrpv3StatisticsAdvIntervalErrors OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of VRRP advertisement packets
received for which the advertisement interval is
different from the vrrpv3OperationsAdvInterval
configured on this virtual router.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
vrrpv3StatisticsRowDiscontinuityTime."
::= { vrrpv3StatisticsEntry 4 }
vrrpv3StatisticsIpTtlErrors OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of VRRP packets received by the
virtual router with IPv4 TTL (for VRRP over IPv4) or
IPv6 Hop Limit (for VRRP over IPv6) not equal to 255.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
vrrpv3StatisticsRowDiscontinuityTime."
REFERENCE "RFC 5798, Section 5.1.1.3"
::= { vrrpv3StatisticsEntry 5 }
vrrpv3StatisticsProtoErrReason OBJECT-TYPE
SYNTAX INTEGER {
noError (0),
ipTtlError (1),
versionError (2),
checksumError (3),
vrIdError(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This indicates the reason for the last protocol
error. This SHOULD be set to noError(0) when no
protocol errors are encountered. Used by
vrrpv3ProtoError notification."
::= { vrrpv3StatisticsEntry 6 }
vrrpv3StatisticsRcvdPriZeroPackets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of VRRP packets received by the
virtual router with a priority of '0'.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
vrrpv3StatisticsRowDiscontinuityTime."
REFERENCE "RFC 5798, Section 5.2.4"
::= { vrrpv3StatisticsEntry 7 }
vrrpv3StatisticsSentPriZeroPackets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of VRRP packets sent by the virtual
router with a priority of '0'.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
vrrpv3StatisticsRowDiscontinuityTime."
REFERENCE "RFC 5798, Section 5.2.4"
::= { vrrpv3StatisticsEntry 8 }
vrrpv3StatisticsRcvdInvalidTypePackets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of VRRP packets received by the virtual
router with an invalid value in the 'type' field.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
vrrpv3StatisticsRowDiscontinuityTime."
::= { vrrpv3StatisticsEntry 9 }
vrrpv3StatisticsAddressListErrors OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of packets received for which the
address list does not match the locally configured
list for the virtual router.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
vrrpv3StatisticsRowDiscontinuityTime."
::= { vrrpv3StatisticsEntry 10 }
vrrpv3StatisticsPacketLengthErrors OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of packets received with a packet
length less than the length of the VRRP header.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
vrrpv3StatisticsRowDiscontinuityTime."
::= { vrrpv3StatisticsEntry 11 }
vrrpv3StatisticsRowDiscontinuityTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime on the most recent occasion at
which any one or more of this entry's counters
suffered a discontinuity.
If no such discontinuities have occurred since the last
re-initialization of the local management subsystem,
then this object contains a zero value."
::= { vrrpv3StatisticsEntry 12 }
vrrpv3StatisticsRefreshRate OBJECT-TYPE
SYNTAX Unsigned32
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The minimum reasonable polling interval for this entry.
This object provides an indication of the minimum
amount of time required to update the counters in this
entry."
::= { vrrpv3StatisticsEntry 13 }
-- Notification Definitions
-- Notifications may be controlled using SNMP-NOTIFICATION-MIB
vrrpv3NewMaster NOTIFICATION-TYPE
OBJECTS {
vrrpv3OperationsMasterIpAddr,
vrrpv3StatisticsNewMasterReason
}
STATUS current
DESCRIPTION
"The newMaster notification indicates that the sending
agent has transitioned to master state."
::= { vrrpv3Notifications 1 }
vrrpv3ProtoError NOTIFICATION-TYPE
OBJECTS {
vrrpv3StatisticsProtoErrReason
}
STATUS current
DESCRIPTION
"The notification indicates that the sending agent has
encountered the protocol error indicated by
vrrpv3StatisticsProtoErrReason."
::= { vrrpv3Notifications 2 }
-- Conformance Information
vrrpv3Compliances OBJECT IDENTIFIER ::= { vrrpv3Conformance 1 }
vrrpv3Groups OBJECT IDENTIFIER ::= { vrrpv3Conformance 2 }
-- Compliance Statements
vrrpv3FullCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement"
MODULE -- this module
MANDATORY-GROUPS {
vrrpv3OperationsGroup,
vrrpv3StatisticsGroup,
vrrpv3InfoGroup,
vrrpv3NotificationsGroup
}
OBJECT vrrpv3OperationsPriority
WRITE-SYNTAX Unsigned32 (1..254)
DESCRIPTION "Setable values are from 1 to 254."
::= { vrrpv3Compliances 1 }
vrrpv3ReadOnlyCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"When this MIB module is implemented without support
for read-create (i.e., in read-only mode), then such
an implementation can claim read-only compliance.
Such a device can then be monitored, but cannot be
configured with this MIB."
MODULE -- this module
MANDATORY-GROUPS {
vrrpv3OperationsGroup,
vrrpv3StatisticsGroup,
vrrpv3StatisticsDiscontinuityGroup,
vrrpv3InfoGroup,
vrrpv3NotificationsGroup
}
OBJECT vrrpv3OperationsPriority
MIN-ACCESS read-only
DESCRIPTION "Write access is not required."
OBJECT vrrpv3OperationsPrimaryIpAddr
MIN-ACCESS read-only
DESCRIPTION "Write access is not required."
OBJECT vrrpv3OperationsAdvInterval
MIN-ACCESS read-only
DESCRIPTION "Write access is not required."
OBJECT vrrpv3OperationsPreemptMode
MIN-ACCESS read-only
DESCRIPTION "Write access is not required."
OBJECT vrrpv3OperationsAcceptMode
MIN-ACCESS read-only
DESCRIPTION "Write access is not required."
OBJECT vrrpv3OperationsRowStatus
MIN-ACCESS read-only
DESCRIPTION "Write access is not required."
OBJECT vrrpv3AssociatedIpAddrRowStatus
MIN-ACCESS read-only
DESCRIPTION "Write access is not required."
::= { vrrpv3Compliances 2 }
-- Conformance Groups
vrrpv3OperationsGroup OBJECT-GROUP
OBJECTS {
vrrpv3OperationsVirtualMacAddr,
vrrpv3OperationsStatus,
vrrpv3OperationsPriority,
vrrpv3OperationsMasterIpAddr,
vrrpv3OperationsAdvInterval,
vrrpv3OperationsPreemptMode,
vrrpv3OperationsAcceptMode,
vrrpv3OperationsUpTime,
vrrpv3OperationsRowStatus,
vrrpv3OperationsAddrCount,
vrrpv3OperationsPrimaryIpAddr,
vrrpv3AssociatedIpAddrRowStatus
}
STATUS current
DESCRIPTION
"Conformance group for VRRPv3 operations."
::= { vrrpv3Groups 1 }
vrrpv3StatisticsGroup OBJECT-GROUP
OBJECTS {
vrrpv3RouterChecksumErrors,
vrrpv3RouterVersionErrors,
vrrpv3RouterVrIdErrors,
vrrpv3StatisticsMasterTransitions,
vrrpv3StatisticsNewMasterReason,
vrrpv3StatisticsRcvdAdvertisements,
vrrpv3StatisticsAdvIntervalErrors,
vrrpv3StatisticsRcvdPriZeroPackets,
vrrpv3StatisticsSentPriZeroPackets,
vrrpv3StatisticsRcvdInvalidTypePackets,
vrrpv3StatisticsIpTtlErrors,
vrrpv3StatisticsProtoErrReason,
vrrpv3StatisticsAddressListErrors,
vrrpv3StatisticsPacketLengthErrors,
vrrpv3StatisticsRowDiscontinuityTime,
vrrpv3StatisticsRefreshRate
}
STATUS current
DESCRIPTION
"Conformance group for VRRPv3 statistics."
::= { vrrpv3Groups 2 }
vrrpv3StatisticsDiscontinuityGroup OBJECT-GROUP
OBJECTS {
vrrpv3GlobalStatisticsDiscontinuityTime
}
STATUS current
DESCRIPTION
"Objects providing information about counter
discontinuities."
::= { vrrpv3Groups 3 }
vrrpv3InfoGroup OBJECT-GROUP
OBJECTS {
vrrpv3StatisticsProtoErrReason,
vrrpv3StatisticsNewMasterReason
}
STATUS current
DESCRIPTION
"Conformance group for objects contained in VRRPv3
notifications."
::= { vrrpv3Groups 4 }
vrrpv3NotificationsGroup NOTIFICATION-GROUP
NOTIFICATIONS {
vrrpv3NewMaster,
vrrpv3ProtoError
}
STATUS current
DESCRIPTION
"The VRRP MIB Notification Group."
::= { vrrpv3Groups 5 }
END