/* * This module has been generated by smidump 0.4.5: * * smidump -f yang MAU-MIB * * Do not edit. Edit the source file instead! */ module MAU-MIB { /*** NAMESPACE / PREFIX DEFINITION ***/ namespace "urn:ietf:params:xml:ns:yang:smiv2:MAU-MIB"; prefix "mau-mib"; /*** LINKAGE (IMPORTS / INCLUDES) ***/ import IANA-MAU-MIB { prefix "iana-mau"; } import IF-MIB { prefix "if-mib"; } import SNMPv2-TC { prefix "smiv2"; } import yang-types { prefix "yang"; } /*** META INFORMATION ***/ organization "IETF Ethernet Interfaces and Hub MIB Working Group"; contact "WG charter: http://www.ietf.org/html.charters/hubmib-charter.html Mailing Lists: General Discussion: hubmib@ietf.org To Subscribe: hubmib-request@ietf.org In Body: subscribe your_email_address Chair: Bert Wijnen Postal: Alcatel-Lucent Schagen 33 3461 GL Linschoten Netherlands Phone: +31-348-407-775 EMail: bwijnen@alcatel-lucent.com Editor: Edward Beili Postal: Actelis Networks Inc. 25 Bazel St., P.O.B. 10173 Petach-Tikva 10173 Israel Tel: +972-3-924-3491 EMail: edward.beili@actelis.com"; description "Management information for 802.3 MAUs. The following reference is used throughout this MIB module: [IEEE802.3] refers to: IEEE Std 802.3, 2005 Edition: 'IEEE Standard for Information technology - Telecommunications and information exchange between systems - Local and metropolitan area networks - Specific requirements - Part 3: Carrier sense multiple access with collision detection (CSMA/CD) access method and physical layer specifications'. Of particular interest is Clause 30, 'Management'. Copyright (C) The IETF Trust (2007). This version of this MIB module is part of RFC 4836; see the RFC itself for full legal notices."; revision "2007-04-21" { description "Updated to reference IANA maintaned textual conventions for MAU types, Media Availability state, Auto Negotiation capabilities, and jack types, instead of using internally defined values. This version is published as RFC 4836."; } revision "2003-09-19" { description "Updated to include support for 10 Gb/s MAUs. This resulted in the following revisions: - Added OBJECT-IDENTITY definitions for 10 gigabit MAU types - Added fiberLC jack type to JackType TC - Extended ifMauTypeListBits with bits for the 10 gigabit MAU types - Added enumerations to ifMauMediaAvailable, and updated its DESCRIPTION to reflect behaviour at 10 Gb/s - Added 64-bit version of ifMauFalseCarriers and added mauIfGrpHCStats object group to contain the new object - Deprecated mauModIfCompl2 and replaced it with mauModIfCompl3, which includes the new object group This version published as RFC 3636."; } revision "1999-08-24" { description "This version published as RFC 2668. Updated to include support for 1000 Mb/sec MAUs and flow control negotiation."; } revision "1997-10-31" { description "Version published as RFC 2239."; } revision "1993-09-30" { description "Initial version, published as RFC 1515."; } /*** TYPE DEFINITIONS ***/ typedef JackType { type enumeration { enum other { value 1; } enum rj45 { value 2; } enum rj45S { value 3; } enum db9 { value 4; } enum bnc { value 5; } enum fAUI { value 6; } enum mAUI { value 7; } enum fiberSC { value 8; } enum fiberMIC { value 9; } enum fiberST { value 10; } enum telco { value 11; } enum mtrj { value 12; } enum hssdc { value 13; } enum fiberLC { value 14; } } status deprecated; description "********* THIS TC IS DEPRECATED ********** This TC has been deprecated in favour of IANAifJackType. Common enumeration values for repeater and interface MAU jack types."; } container dot3RpMauBasicGroup { /* XXX table comments here XXX */ list rpMauEntry { key "rpMauGroupIndex rpMauPortIndex rpMauIndex"; description "An entry in the table, containing information about a single MAU."; leaf rpMauGroupIndex { type int32 { range "1..2147483647"; } config false; description "This variable uniquely identifies the group containing the port to which the MAU described by this entry is connected. Note: In practice, a group will generally be a field-replaceable unit (i.e., module, card, or board) that can fit in the physical system enclosure, and the group number will correspond to a number marked on the physical enclosure. The group denoted by a particular value of this object is the same as the group denoted by the same value of rptrGroupIndex."; reference "RFC 2108, rptrGroupIndex."; } leaf rpMauPortIndex { type int32 { range "1..2147483647"; } config false; description "This variable uniquely identifies the repeater port within group rpMauGroupIndex to which the MAU described by this entry is connected."; reference "RFC 2108, rptrPortIndex."; } leaf rpMauIndex { type int32 { range "1..2147483647"; } config false; description "This variable uniquely identifies the MAU described by this entry from among other MAUs connected to the same port (rpMauPortIndex)."; reference "[IEEE802.3], 30.5.1.1.1, aMAUID."; } leaf rpMauType { type smiv2:AutonomousType; config false; description "This object identifies the MAU type. Values for standard IEEE 802.3 MAU types are defined in the IANA maintained IANA-MAU-MIB module, as OBJECT-IDENTITIES of dot3MauType. If the MAU type is unknown, the object identifier zeroDotZero is returned."; reference "[IEEE802.3], 30.5.1.1.2, aMAUType."; } leaf rpMauStatus { type enumeration { enum other { value 1; } enum unknown { value 2; } enum operational { value 3; } enum standby { value 4; } enum shutdown { value 5; } enum reset { value 6; } } config true; description "The current state of the MAU. This object MAY be implemented as a read-only object by those agents and MAUs that do not implement software control of the MAU state. Some agents may not support setting the value of this object to some of the enumerated values. The value other(1) is returned if the MAU is in a state other than one of the states 2 through 6. The value unknown(2) is returned when the MAU's true state is unknown; for example, when it is being initialized. A MAU in the operational(3) state is fully functional; it operates, and passes signals to its attached DTE or repeater port in accordance to its specification. A MAU in standby(4) state forces DI and CI to idle, and the media transmitter to idle or fault, if supported. Standby(4) mode only applies to link type MAUs. The state of rpMauMediaAvailable is unaffected. A MAU in shutdown(5) state assumes the same condition on DI, CI, and the media transmitter, as though it were powered down or not connected. The MAU MAY return other(1) value for the rpMauJabberState and rpMauMediaAvailable objects when it is in this state. For an AUI, this state will remove power from the AUI. Setting this variable to the value reset(6) resets the MAU in the same manner as a power-off, power-on cycle of at least one-half second would. The agent is not required to return the value reset(6). Setting this variable to the value operational(3), standby(4), or shutdown(5) causes the MAU to assume the respective state, except that setting a mixing-type MAU or an AUI to standby(4) will cause the MAU to enter the shutdown state."; reference "[IEEE802.3], 30.5.1.1.7, aMAUAdminState, 30.5.1.2.2, acMAUAdminControl, and 30.5.1.2.1, acResetMAU."; } leaf rpMauMediaAvailable { type iana-mau:IANAifMauMediaAvailable; config false; description "This object identifies Media Available state of the MAU, complementary to the rpMauStatus. Values for the standard IEEE 802.3 Media Available states are defined in the IANA maintained IANA-MAU-MIB module, as IANAifMauMediaAvailable TC."; reference "[IEEE802.3], 30.5.1.1.4, aMediaAvailable."; } leaf rpMauMediaAvailableStateExits { type yang:counter32; config false; description "A count of the number of times that rpMauMediaAvailable for this MAU instance leaves the state available(3). Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times, as indicated by the value of rptrMonitorPortLastChange."; reference "[IEEE802.3], 30.5.1.1.5, aLoseMediaCounter. RFC 2108, rptrMonitorPortLastChange"; } leaf rpMauJabberState { type enumeration { enum other { value 1; } enum unknown { value 2; } enum noJabber { value 3; } enum jabbering { value 4; } } config false; description "The value other(1) is returned if the jabber state is not 2, 3, or 4. The agent MUST always return other(1) for MAU type dot3MauTypeAUI. The value unknown(2) is returned when the MAU's true state is unknown; for example, when it is being initialized. If the MAU is not jabbering the agent returns noJabber(3). This is the 'normal' state. If the MAU is in jabber state the agent returns the jabbering(4) value."; reference "[IEEE802.3], 30.5.1.1.6, aJabber.jabberFlag."; } leaf rpMauJabberingStateEnters { type yang:counter32; config false; description "A count of the number of times that mauJabberState for this MAU instance enters the state jabbering(4). For MAUs of type dot3MauTypeAUI, dot3MauType100BaseT4, dot3MauType100BaseTX, dot3MauType100BaseFX, and all 1000Mbps types, this counter will always indicate zero. Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times, as indicated by the value of rptrMonitorPortLastChange."; reference "[IEEE802.3], 30.5.1.1.6, aJabber.jabberCounter. RFC 2108, rptrMonitorPortLastChange"; } leaf rpMauFalseCarriers { type yang:counter32; config false; description "A count of the number of false carrier events during IDLE in 100BASE-X links. This counter does not increment at the symbol rate. It can increment after a valid carrier completion at a maximum rate of once per 100 ms until the next carrier event. This counter increments only for MAUs of type dot3MauType100BaseT4, dot3MauType100BaseTX, dot3MauType100BaseFX, and all 1000Mbps types. For all other MAU types, this counter will always indicate zero. The approximate minimum time for rollover of this counter is 7.4 hours. Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times, as indicated by the value of rptrMonitorPortLastChange."; reference "[IEEE802.3], 30.5.1.1.10, aFalseCarriers. RFC 2108, rptrMonitorPortLastChange"; } } /* XXX table comments here XXX */ list rpJackEntry { key "rpMauGroupIndex rpMauPortIndex rpMauIndex rpJackIndex"; description "An entry in the table, containing information about a particular jack."; leaf rpMauGroupIndex { type keyref { path "/mau-mib:dot3RpMauBasicGroup/mau-mib:rpMauEntry/mau-mib:rpMauGroupIndex"; } config false; description "Automagically generated keyref leaf."; } leaf rpMauPortIndex { type keyref { path "/mau-mib:dot3RpMauBasicGroup/mau-mib:rpMauEntry/mau-mib:rpMauPortIndex"; } config false; description "Automagically generated keyref leaf."; } leaf rpMauIndex { type keyref { path "/mau-mib:dot3RpMauBasicGroup/mau-mib:rpMauEntry/mau-mib:rpMauIndex"; } config false; description "Automagically generated keyref leaf."; } leaf rpJackIndex { type int32 { range "1..2147483647"; } config false; description "This variable uniquely identifies the jack described by this entry from among other jacks attached to the same MAU (rpMauIndex)."; } leaf rpJackType { type iana-mau:IANAifJackType; config false; description "The jack connector type, as it appears on the outside of the system."; } } } container dot3IfMauBasicGroup { /* XXX table comments here XXX */ list ifMauEntry { key "ifMauIfIndex ifMauIndex"; description "An entry in the table, containing information about a single MAU."; leaf ifMauIfIndex { type if-mib:InterfaceIndex; config false; description "This variable uniquely identifies the interface to which the MAU described by this entry is connected."; reference "RFC 2863, ifIndex"; } leaf ifMauIndex { type int32 { range "1..2147483647"; } config false; description "This variable uniquely identifies the MAU described by this entry from among other MAUs connected to the same interface (ifMauIfIndex)."; reference "[IEEE802.3], 30.5.1.1.1, aMAUID."; } leaf ifMauType { type smiv2:AutonomousType; config false; description "This object identifies the MAU type. Values for standard IEEE 802.3 MAU types are defined in the IANA maintained IANA-MAU-MIB module, as OBJECT-IDENTITIES of dot3MauType. If the MAU type is unknown, the object identifier zeroDotZero is returned. This object represents the operational type of the MAU, as determined by either 1) the result of the auto-negotiation function or 2) if auto-negotiation is not enabled or is not implemented for this MAU, by the value of the object ifMauDefaultType. In case 2), a set to the object ifMauDefaultType will force the MAU into the new operating mode."; reference "[IEEE802.3], 30.5.1.1.2, aMAUType."; } leaf ifMauStatus { type enumeration { enum other { value 1; } enum unknown { value 2; } enum operational { value 3; } enum standby { value 4; } enum shutdown { value 5; } enum reset { value 6; } } config true; description "The current state of the MAU. This object MAY be implemented as a read-only object by those agents and MAUs that do not implement software control of the MAU state. Some agents may not support setting the value of this object to some of the enumerated values. The value other(1) is returned if the MAU is in a state other than one of the states 2 through 6. The value unknown(2) is returned when the MAU's true state is unknown; for example, when it is being initialized. A MAU in the operational(3) state is fully functional; it operates, and passes signals to its attached DTE or repeater port in accordance to its specification. A MAU in standby(4) state forces DI and CI to idle and the media transmitter to idle or fault, if supported. Standby(4) mode only applies to link type MAUs. The state of ifMauMediaAvailable is unaffected. A MAU in shutdown(5) state assumes the same condition on DI, CI, and the media transmitter, as though it were powered down or not connected. The MAU MAY return other(1) value for the ifMauJabberState and ifMauMediaAvailable objects when it is in this state. For an AUI, this state will remove power from the AUI. Setting this variable to the value reset(6) resets the MAU in the same manner as a power-off, power-on cycle of at least one-half second would. The agent is not required to return the value reset(6). Setting this variable to the value operational(3), standby(4), or shutdown(5) causes the MAU to assume the respective state, except that setting a mixing-type MAU or an AUI to standby(4) will cause the MAU to enter the shutdown state."; reference "[IEEE802.3], 30.5.1.1.7, aMAUAdminState, 30.5.1.2.2, acMAUAdminControl, and 30.5.1.2.1, acResetMAU."; } leaf ifMauMediaAvailable { type iana-mau:IANAifMauMediaAvailable; config false; description "This object identifies Media Available state of the MAU, complementary to the ifMauStatus. Values for the standard IEEE 802.3 Media Available states are defined in the IANA maintained IANA-MAU-MIB module, as IANAifMauMediaAvailable TC."; reference "[IEEE802.3], 30.5.1.1.4, aMediaAvailable."; } leaf ifMauMediaAvailableStateExits { type yang:counter32; config false; description "A count of the number of times that ifMauMediaAvailable for this MAU instance leaves the state available(3). Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times, as indicated by the value of ifCounterDiscontinuityTime."; reference "[IEEE802.3], 30.5.1.1.5, aLoseMediaCounter. RFC 2863, ifCounterDiscontinuityTime."; } leaf ifMauJabberState { type enumeration { enum other { value 1; } enum unknown { value 2; } enum noJabber { value 3; } enum jabbering { value 4; } } config false; description "The value other(1) is returned if the jabber state is not 2, 3, or 4. The agent MUST always return other(1) for MAU type dot3MauTypeAUI. The value unknown(2) is returned when the MAU's true state is unknown; for example, when it is being initialized. If the MAU is not jabbering the agent returns noJabber(3). This is the 'normal' state. If the MAU is in jabber state the agent returns the jabbering(4) value."; reference "[IEEE802.3], 30.5.1.1.6, aJabber.jabberFlag."; } leaf ifMauJabberingStateEnters { type yang:counter32; config false; description "A count of the number of times that mauJabberState for this MAU instance enters the state jabbering(4). This counter will always indicate zero for MAUs of type dot3MauTypeAUI and those of speeds above 10Mbps. Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times, as indicated by the value of ifCounterDiscontinuityTime."; reference "[IEEE802.3], 30.5.1.1.6, aJabber.jabberCounter. RFC 2863, ifCounterDiscontinuityTime."; } leaf ifMauFalseCarriers { type yang:counter32; config false; description "A count of the number of false carrier events during IDLE in 100BASE-X and 1000BASE-X links. For all other MAU types, this counter will always indicate zero. This counter does not increment at the symbol rate. It can increment after a valid carrier completion at a maximum rate of once per 100 ms for 100BASE-X and once per 10us for 1000BASE-X until the next CarrierEvent. This counter can roll over very quickly. A management station is advised to poll the ifMauHCFalseCarriers instead of this counter in order to avoid loss of information. Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times, as indicated by the value of ifCounterDiscontinuityTime."; reference "[IEEE802.3], 30.5.1.1.10, aFalseCarriers. RFC 2863, ifCounterDiscontinuityTime."; } leaf ifMauTypeList { type int32; config false; status deprecated; description "********* THIS OBJECT IS DEPRECATED ********** This object has been deprecated in favour of ifMauTypeListBits. A value that uniquely identifies the set of possible IEEE 802.3 types that the MAU could be. The value is a sum that initially takes the value zero. Then, for each type capability of this MAU, 2 raised to the power noted below is added to the sum. For example, a MAU that has the capability to be only 10BASE-T would have a value of 512 (2**9). In contrast, a MAU that supports both 10Base-T (full duplex) and 100BASE-TX (full duplex) would have a value of ((2**11) + (2**16)), or 67584. The powers of 2 assigned to the capabilities are these: Power Capability 0 other or unknown 1 AUI 2 10BASE-5 3 FOIRL 4 10BASE-2 5 10BASE-T duplex mode unknown 6 10BASE-FP 7 10BASE-FB 8 10BASE-FL duplex mode unknown 9 10BROAD36 10 10BASE-T half duplex mode 11 10BASE-T full duplex mode 12 10BASE-FL half duplex mode 13 10BASE-FL full duplex mode 14 100BASE-T4 15 100BASE-TX half duplex mode 16 100BASE-TX full duplex mode 17 100BASE-FX half duplex mode 18 100BASE-FX full duplex mode 19 100BASE-T2 half duplex mode 20 100BASE-T2 full duplex mode If auto-negotiation is present on this MAU, this object will map to ifMauAutoNegCapability."; } leaf ifMauDefaultType { type smiv2:AutonomousType; config true; description "This object identifies the default administrative baseband MAU type to be used in conjunction with the operational MAU type denoted by ifMauType. The set of possible values for this object is the same as the set defined for the ifMauType object. This object represents the administratively-configured type of the MAU. If auto-negotiation is not enabled or is not implemented for this MAU, the value of this object determines the operational type of the MAU. In this case, a set to this object will force the MAU into the specified operating mode. If auto-negotiation is implemented and enabled for this MAU, the operational type of the MAU is determined by auto-negotiation, and the value of this object denotes the type to which the MAU will automatically revert if/when auto-negotiation is later disabled. NOTE TO IMPLEMENTORS: It may be necessary to provide for underlying hardware implementations which do not follow the exact behavior specified above. In particular, when ifMauAutoNegAdminStatus transitions from enabled to disabled, the agent implementation MUST ensure that the operational type of the MAU (as reported by ifMauType) correctly transitions to the value specified by this object, rather than continuing to operate at the value earlier determined by the auto-negotiation function."; reference "[IEEE802.3], 30.5.1.1.1, aMAUID, and 22.2.4.1.4."; } leaf ifMauAutoNegSupported { type smiv2:TruthValue; config false; description "This object indicates whether or not auto-negotiation is supported on this MAU."; } leaf ifMauTypeListBits { type iana-mau:IANAifMauTypeListBits; config false; description "A value that uniquely identifies the set of possible IEEE 802.3 types that the MAU could be. If auto-negotiation is present on this MAU, this object will map to ifMauAutoNegCapabilityBits. Note that this MAU may be capable of operating as a MAU type that is beyond the scope of this MIB. This is indicated by returning the bit value bOther in addition to any bit values for standard capabilities that are listed in the IANAifMauTypeListBits TC."; } leaf ifMauHCFalseCarriers { type yang:counter64; config false; description "A count of the number of false carrier events during IDLE in 100BASE-X and 1000BASE-X links. For all other MAU types, this counter will always indicate zero. This counter does not increment at the symbol rate. This counter is a 64-bit version of ifMauFalseCarriers. Since the 32-bit version of this counter can roll over very quickly, management stations are advised to poll the 64-bit version instead, in order to avoid loss of information. Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times, as indicated by the value of ifCounterDiscontinuityTime."; reference "[IEEE802.3], 30.5.1.1.10, aFalseCarriers. RFC 2863, ifCounterDiscontinuityTime."; } } /* XXX table comments here XXX */ list ifJackEntry { key "ifMauIfIndex ifMauIndex ifJackIndex"; description "An entry in the table, containing information about a particular jack."; leaf ifMauIfIndex { type keyref { path "/mau-mib:dot3IfMauBasicGroup/mau-mib:ifMauEntry/mau-mib:ifMauIfIndex"; } config false; description "Automagically generated keyref leaf."; } leaf ifMauIndex { type keyref { path "/mau-mib:dot3IfMauBasicGroup/mau-mib:ifMauEntry/mau-mib:ifMauIndex"; } config false; description "Automagically generated keyref leaf."; } leaf ifJackIndex { type int32 { range "1..2147483647"; } config false; description "This variable uniquely identifies the jack described by this entry from among other jacks attached to the same MAU."; } leaf ifJackType { type iana-mau:IANAifJackType; config false; description "The jack connector type, as it appears on the outside of the system."; } } } container dot3IfMauAutoNegGroup { /* XXX table comments here XXX */ list ifMauAutoNegEntry { key "ifMauIfIndex ifMauIndex"; description "An entry in the table, containing configuration and status information for the auto-negotiation function of a particular MAU."; leaf ifMauIfIndex { type keyref { path "/mau-mib:dot3IfMauBasicGroup/mau-mib:ifMauEntry/mau-mib:ifMauIfIndex"; } config false; description "Automagically generated keyref leaf."; } leaf ifMauIndex { type keyref { path "/mau-mib:dot3IfMauBasicGroup/mau-mib:ifMauEntry/mau-mib:ifMauIndex"; } config false; description "Automagically generated keyref leaf."; } leaf ifMauAutoNegAdminStatus { type enumeration { enum enabled { value 1; } enum disabled { value 2; } } config true; description "Setting this object to enabled(1) will cause the interface that has the auto-negotiation signaling ability to be enabled. If the value of this object is disabled(2) then the interface will act as it would if it had no auto-negotiation signaling. Under these conditions, an IEEE 802.3 MAU will immediately be forced to the state indicated by the value of the object ifMauDefaultType. NOTE TO IMPLEMENTORS: When ifMauAutoNegAdminStatus transitions from enabled to disabled, the agent implementation MUST ensure that the operational type of the MAU (as reported by ifMauType) correctly transitions to the value specified by the ifMauDefaultType object, rather than continuing to operate at the value earlier determined by the auto-negotiation function."; reference "[IEEE802.3], 30.6.1.1.2, aAutoNegAdminState, and 30.6.1.2.2, acAutoNegAdminControl."; } leaf ifMauAutoNegRemoteSignaling { type enumeration { enum detected { value 1; } enum notdetected { value 2; } } config false; description "A value indicating whether the remote end of the link is using auto-negotiation signaling. It takes the value detected(1) if and only if, during the previous link negotiation, FLP Bursts were received."; reference "[IEEE802.3], 30.6.1.1.3, aAutoNegRemoteSignaling."; } leaf ifMauAutoNegConfig { type enumeration { enum other { value 1; } enum configuring { value 2; } enum complete { value 3; } enum disabled { value 4; } enum parallelDetectFail { value 5; } } config false; description "A value indicating the current status of the auto-negotiation process. The enumeration parallelDetectFail(5) maps to a failure in parallel detection as defined in 28.2.3.1 of [IEEE802.3]."; reference "[IEEE802.3], 30.6.1.1.4, aAutoNegAutoConfig."; } leaf ifMauAutoNegCapability { type int32; config false; status deprecated; description "********* THIS OBJECT IS DEPRECATED ********** This object has been deprecated in favour of ifMauAutoNegCapabilityBits. A value that uniquely identifies the set of capabilities of the local auto-negotiation entity. The value is a sum that initially takes the value zero. Then, for each capability of this interface, 2 raised to the power noted below is added to the sum. For example, an interface that has the capability to support only 100Base-TX half duplex would have a value of 32768 (2**15). In contrast, an interface that supports both 100Base-TX half duplex and 100Base-TX full duplex would have a value of 98304 ((2**15) + (2**16)). The powers of 2 assigned to the capabilities are these: Power Capability 0 other or unknown (1-9) (reserved) 10 10BASE-T half duplex mode 11 10BASE-T full duplex mode 12 (reserved) 13 (reserved) 14 100BASE-T4 15 100BASE-TX half duplex mode 16 100BASE-TX full duplex mode 17 (reserved) 18 (reserved) 19 100BASE-T2 half duplex mode 20 100BASE-T2 full duplex mode Note that interfaces that support this MIB may have capabilities that extend beyond the scope of this MIB."; reference "[IEEE802.3], 30.6.1.1.5, aAutoNegLocalTechnologyAbility."; } leaf ifMauAutoNegCapAdvertised { type int32; config true; status deprecated; description "********* THIS OBJECT IS DEPRECATED ********** This object has been deprecated in favour of ifMauAutoNegCapAdvertisedBits. A value that uniquely identifies the set of capabilities advertised by the local auto-negotiation entity. Refer to ifMauAutoNegCapability for a description of the possible values of this object. Capabilities in this object that are not available in ifMauAutoNegCapability cannot be enabled."; reference "[IEEE802.3], 30.6.1.1.6, aAutoNegAdvertisedTechnologyAbility."; } leaf ifMauAutoNegCapReceived { type int32; config false; status deprecated; description "********* THIS OBJECT IS DEPRECATED ********** This object has been deprecated in favour of ifMauAutoNegCapReceivedBits. A value that uniquely identifies the set of capabilities received from the remote auto-negotiation entity. Refer to ifMauAutoNegCapability for a description of the possible values of this object. Note that interfaces that support this MIB may be attached to remote auto-negotiation entities that have capabilities beyond the scope of this MIB."; reference "[IEEE802.3], 30.6.1.1.7, aAutoNegReceivedTechnologyAbility."; } leaf ifMauAutoNegRestart { type enumeration { enum restart { value 1; } enum norestart { value 2; } } config true; description "If the value of this object is set to restart(1) then this will force auto-negotiation to begin link renegotiation. If auto-negotiation signaling is disabled, a write to this object has no effect. Setting the value of this object to norestart(2) has no effect."; reference "[IEEE802.3], 30.6.1.2.1, acAutoNegRestartAutoConfig."; } leaf ifMauAutoNegCapabilityBits { type iana-mau:IANAifMauAutoNegCapBits; config false; description "A value that uniquely identifies the set of capabilities of the local auto-negotiation entity. Note that interfaces that support this MIB may have capabilities that extend beyond the scope of this MIB. Note that the local auto-negotiation entity may support some capabilities beyond the scope of this MIB. This is indicated by returning the bit value bOther in addition to any bit values for standard capabilities that are listed in the IANAifMauAutoNegCapBits TC."; reference "[IEEE802.3], 30.6.1.1.5, aAutoNegLocalTechnologyAbility."; } leaf ifMauAutoNegCapAdvertisedBits { type iana-mau:IANAifMauAutoNegCapBits; config true; description "A value that uniquely identifies the set of capabilities advertised by the local auto-negotiation entity. Capabilities in this object that are not available in ifMauAutoNegCapabilityBits cannot be enabled. Note that the local auto-negotiation entity may advertise some capabilities beyond the scope of this MIB. This is indicated by returning the bit value bOther in addition to any bit values for standard capabilities that are listed in the IANAifMauAutoNegCapBits TC."; reference "[IEEE802.3], 30.6.1.1.6, aAutoNegAdvertisedTechnologyAbility."; } leaf ifMauAutoNegCapReceivedBits { type iana-mau:IANAifMauAutoNegCapBits; config false; description "A value that uniquely identifies the set of capabilities received from the remote auto-negotiation entity. Note that interfaces that support this MIB may be attached to remote auto-negotiation entities that have capabilities beyond the scope of this MIB. This is indicated by returning the bit value bOther in addition to any bit values for standard capabilities that are listed in the IANAifMauAutoNegCapBits TC."; reference "[IEEE802.3], 30.6.1.1.7, aAutoNegReceivedTechnologyAbility."; } leaf ifMauAutoNegRemoteFaultAdvertised { type enumeration { enum noError { value 1; } enum offline { value 2; } enum linkFailure { value 3; } enum autoNegError { value 4; } } config true; description "A value that identifies any local fault indications that this MAU has detected and will advertise at the next auto-negotiation interaction for 1000Mbps MAUs."; reference "[IEEE802.3], 30.6.1.1.6, aAutoNegAdvertisedTechnologyAbility."; } leaf ifMauAutoNegRemoteFaultReceived { type enumeration { enum noError { value 1; } enum offline { value 2; } enum linkFailure { value 3; } enum autoNegError { value 4; } } config false; description "A value that identifies any fault indications received from the far end of a link by the local auto-negotiation entity for 1000Mbps MAUs."; reference "[IEEE802.3], 30.6.1.1.7, aAutoNegReceivedTechnologyAbility."; } } } notification rpMauJabberTrap { description "This trap is sent whenever a managed repeater MAU enters the jabber state. The agent MUST throttle the generation of consecutive rpMauJabberTraps so that there is at least a five-second gap between them."; reference "[IEEE802.3], 30.5.1.3.1, nJabber notification."; container rpMauJabberTrap-rpMauJabberState { leaf rpMauGroupIndex { type keyref { path "/mau-mib:dot3RpMauBasicGroup/mau-mib:rpMauEntry/mau-mib:rpMauGroupIndex"; } config false; description "Automagically generated keyref leaf."; } leaf rpMauPortIndex { type keyref { path "/mau-mib:dot3RpMauBasicGroup/mau-mib:rpMauEntry/mau-mib:rpMauPortIndex"; } config false; description "Automagically generated keyref leaf."; } leaf rpMauIndex { type keyref { path "/mau-mib:dot3RpMauBasicGroup/mau-mib:rpMauEntry/mau-mib:rpMauIndex"; } config false; description "Automagically generated keyref leaf."; } leaf rpMauJabberState { type enumeration { enum other { value 1; } enum unknown { value 2; } enum noJabber { value 3; } enum jabbering { value 4; } } config false; description "The value other(1) is returned if the jabber state is not 2, 3, or 4. The agent MUST always return other(1) for MAU type dot3MauTypeAUI. The value unknown(2) is returned when the MAU's true state is unknown; for example, when it is being initialized. If the MAU is not jabbering the agent returns noJabber(3). This is the 'normal' state. If the MAU is in jabber state the agent returns the jabbering(4) value."; reference "[IEEE802.3], 30.5.1.1.6, aJabber.jabberFlag."; } } } notification ifMauJabberTrap { description "This trap is sent whenever a managed interface MAU enters the jabber state. The agent MUST throttle the generation of consecutive ifMauJabberTraps so that there is at least a five-second gap between them."; reference "[IEEE802.3], 30.5.1.3.1, nJabber notification."; container ifMauJabberTrap-ifMauJabberState { leaf ifMauIfIndex { type keyref { path "/mau-mib:dot3IfMauBasicGroup/mau-mib:ifMauEntry/mau-mib:ifMauIfIndex"; } config false; description "Automagically generated keyref leaf."; } leaf ifMauIndex { type keyref { path "/mau-mib:dot3IfMauBasicGroup/mau-mib:ifMauEntry/mau-mib:ifMauIndex"; } config false; description "Automagically generated keyref leaf."; } leaf ifMauJabberState { type enumeration { enum other { value 1; } enum unknown { value 2; } enum noJabber { value 3; } enum jabbering { value 4; } } config false; description "The value other(1) is returned if the jabber state is not 2, 3, or 4. The agent MUST always return other(1) for MAU type dot3MauTypeAUI. The value unknown(2) is returned when the MAU's true state is unknown; for example, when it is being initialized. If the MAU is not jabbering the agent returns noJabber(3). This is the 'normal' state. If the MAU is in jabber state the agent returns the jabbering(4) value."; reference "[IEEE802.3], 30.5.1.1.6, aJabber.jabberFlag."; } } } } /* end of module MAU-MIB */