ISCSI-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE, OBJECT-IDENTITY, NOTIFICATION-TYPE,
Unsigned32, Counter32, Counter64, Gauge32,
mib-2
FROM SNMPv2-SMI
TEXTUAL-CONVENTION, TruthValue, RowPointer, TimeStamp, RowStatus,
AutonomousType, StorageType
FROM SNMPv2-TC
MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP
FROM SNMPv2-CONF
SnmpAdminString
FROM SNMP-FRAMEWORK-MIB -- RFC 3411
InetAddressType, InetAddress, InetPortNumber
FROM INET-ADDRESS-MIB -- RFC 4001
;
iscsiMibModule MODULE-IDENTITY
LAST-UPDATED "200605220000Z" -- May 22, 2006
ORGANIZATION "IETF IPS Working Group"
CONTACT-INFO
"
Mark Bakke
Cisco Systems, Inc
7900 International Drive, Suite 400
Bloomington, MN
USA 55425
E-mail: mbakke@cisco.com
Marjorie Krueger
Hewlett-Packard
Networked Storage Architecture
Networked Storage Solutions Org.
8000 Foothills Blvd.
Roseville, CA 95747
E-mail: marjorie_krueger@hp.com
Tom McSweeney
IBM Corporation
600 Park Offices Drive
Research Triangle Park, NC
USA 27709
E-mail: tommcs@us.ibm.com
James Muchow
Qlogic Corp.
6321 Bury Dr.
Eden Prairie, MN
USA 55346
E-mail: james.muchow@qlogic.com"
DESCRIPTION
"The iSCSI Protocol MIB module.
Copyright (C) The Internet Society (2006). This version of
this MIB module is part of RFC 4544; see the RFC itself for
full legal notices."
REVISION "200605220000Z" -- May 22, 2006
DESCRIPTION
"Initial version of the iSCSI Protocol MIB module"
::= { mib-2 142 }
iscsiNotifications OBJECT IDENTIFIER ::= { iscsiMibModule 0 }
iscsiObjects OBJECT IDENTIFIER ::= { iscsiMibModule 1 }
iscsiConformance OBJECT IDENTIFIER ::= { iscsiMibModule 2 }
iscsiAdmin OBJECT IDENTIFIER ::= { iscsiMibModule 3 }
-- Textual Conventions
IscsiTransportProtocol ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS current
DESCRIPTION
"This data type is used to define the transport
protocols that will carry iSCSI PDUs."
REFERENCE
"RFC791, RFC1700
The presently known, officially delegated numbers
can be found at:
http://www.iana.org/assignments/protocol-numbers"
SYNTAX Unsigned32 (0..255)
IscsiDigestMethod ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This data type represents the methods possible
for digest negotiation.
none - a placeholder for a secondary digest method
that means only the primary method can be
used.
other - a digest method other than those defined below.
noDigest - does not support digests (will operate without
a digest (Note: implementations must support
digests to be compliant with the RFC3720).
CRC32c - require a CRC32C digest."
REFERENCE
"RFC 3720, Section 12.1, HeaderDigest and DataDigest"
SYNTAX INTEGER {
none(1),
other(2),
noDigest(3),
crc32c(4)
}
IscsiName ::= TEXTUAL-CONVENTION
DISPLAY-HINT "223t"
STATUS current
DESCRIPTION
"This data type is used for objects whose value is an
iSCSI name with the properties described in RFC 3720
section 3.2.6.1, and encoded as specified in RFC 3720
section 3.2.6.2. A zero-length string indicates the
absence of an iSCSI name."
REFERENCE
"RFC 3720, Section 3.2.6, iSCSI Names."
SYNTAX OCTET STRING (SIZE(0 | 16..223))
--**********************************************************************
iscsiDescriptors OBJECT IDENTIFIER ::= { iscsiAdmin 1 }
iscsiHeaderIntegrityTypes OBJECT IDENTIFIER ::= { iscsiDescriptors 1 }
iscsiHdrIntegrityNone OBJECT-IDENTITY
STATUS current
DESCRIPTION
"The authoritative identifier when no integrity
scheme (for either the header or data) is being
used."
REFERENCE
"RFC 3720, Section 12.1, HeaderDigest and DataDigest"
::= { iscsiHeaderIntegrityTypes 1 }
iscsiHdrIntegrityCrc32c OBJECT-IDENTITY
STATUS current
DESCRIPTION
"The authoritative identifier when the integrity
scheme (for either the header or data) is CRC32c."
REFERENCE
"RFC 3720, Section 12.1, HeaderDigest and DataDigest"
::= { iscsiHeaderIntegrityTypes 2 }
iscsiDataIntegrityTypes OBJECT IDENTIFIER ::= { iscsiDescriptors 2 }
iscsiDataIntegrityNone OBJECT-IDENTITY
STATUS current
DESCRIPTION
"The authoritative identifier when no integrity
scheme (for either the header or data) is being
used."
REFERENCE
"RFC 3720, Section 12.1, HeaderDigest and DataDigest"
::= { iscsiDataIntegrityTypes 1 }
iscsiDataIntegrityCrc32c OBJECT-IDENTITY
STATUS current
DESCRIPTION
"The authoritative identifier when the integrity
scheme (for either the header or data) is CRC32c."
REFERENCE
"RFC 3720, Section 12.1, HeaderDigest and DataDigest"
::= { iscsiDataIntegrityTypes 2 }
--**********************************************************************
iscsiInstance OBJECT IDENTIFIER ::= { iscsiObjects 1 }
-- Instance Attributes Table
iscsiInstanceAttributesTable OBJECT-TYPE
SYNTAX SEQUENCE OF IscsiInstanceAttributesEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of iSCSI instances present on the system."
::= { iscsiInstance 1 }
iscsiInstanceAttributesEntry OBJECT-TYPE
SYNTAX IscsiInstanceAttributesEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (row) containing management information applicable
to a particular iSCSI instance."
INDEX { iscsiInstIndex }
::= { iscsiInstanceAttributesTable 1 }
IscsiInstanceAttributesEntry ::= SEQUENCE {
iscsiInstIndex Unsigned32,
iscsiInstDescr SnmpAdminString,
iscsiInstVersionMin Unsigned32,
iscsiInstVersionMax Unsigned32,
iscsiInstVendorID SnmpAdminString,
iscsiInstVendorVersion SnmpAdminString,
iscsiInstPortalNumber Unsigned32,
iscsiInstNodeNumber Unsigned32,
iscsiInstSessionNumber Unsigned32,
iscsiInstSsnFailures Counter32,
iscsiInstLastSsnFailureType AutonomousType,
iscsiInstLastSsnRmtNodeName IscsiName,
iscsiInstDiscontinuityTime TimeStamp
}
iscsiInstIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An arbitrary integer used to uniquely identify a particular
iSCSI instance. This index value must not be modified or
reused by an agent unless a reboot has occurred. An agent
should attempt to keep this value persistent across reboots."
::= { iscsiInstanceAttributesEntry 1 }
iscsiInstDescr OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A UTF-8 string, determined by the implementation to
describe the iSCSI instance. When only a single instance
is present, this object may be set to the zero-length
string; with multiple iSCSI instances, it may be used in
an implementation-dependent manner to describe the purpose
of the respective instance."
::= { iscsiInstanceAttributesEntry 2 }
iscsiInstVersionMin OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The minimum version number of the iSCSI specification
such that this iSCSI instance supports this minimum
value, the maximum value indicated by the corresponding
instance in iscsiInstVersionMax, and all versions in
between."
REFERENCE
"RFC 3720, Section 10.12, Login Request"
::= { iscsiInstanceAttributesEntry 3 }
iscsiInstVersionMax OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum version number of the iSCSI specification
such that this iSCSI instance supports this maximum
value, the minimum value indicated by the corresponding
instance in iscsiInstVersionMin, and all versions in
between."
REFERENCE
"RFC 3720, Section 10.12, Login Request"
::= { iscsiInstanceAttributesEntry 4 }
iscsiInstVendorID OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A UTF-8 string describing the manufacturer of the
implementation of this instance."
::= { iscsiInstanceAttributesEntry 5 }
iscsiInstVendorVersion OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A UTF-8 string set by the manufacturer describing the
version of the implementation of this instance. The
format of this string is determined solely by the
manufacturer, and is for informational purposes only.
It is unrelated to the iSCSI specification version numbers."
::= { iscsiInstanceAttributesEntry 6 }
iscsiInstPortalNumber OBJECT-TYPE
SYNTAX Unsigned32
UNITS "transport endpoints"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of rows in the iscsiPortalAttributesTable
that are currently associated with this iSCSI instance."
::= { iscsiInstanceAttributesEntry 7 }
iscsiInstNodeNumber OBJECT-TYPE
SYNTAX Unsigned32
UNITS "iSCSI nodes"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of rows in the iscsiNodeAttributesTable
that are currently associated with this iSCSI instance."
::= { iscsiInstanceAttributesEntry 8 }
iscsiInstSessionNumber OBJECT-TYPE
SYNTAX Unsigned32
UNITS "sessions"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of rows in the iscsiSessionAttributesTable
that are currently associated with this iSCSI instance."
::= { iscsiInstanceAttributesEntry 9 }
iscsiInstSsnFailures OBJECT-TYPE
SYNTAX Counter32
UNITS "sessions"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of times a session belonging
to this instance has been failed. If this counter has
suffered a discontinuity, the time of the last discontinuity
is indicated in iscsiInstDiscontinuityTime."
REFERENCE
"RFC 3720, Section 12.1, HeaderDigest and DataDigest"
::= { iscsiInstanceAttributesEntry 10 }
iscsiInstLastSsnFailureType OBJECT-TYPE
SYNTAX AutonomousType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter object in the iscsiInstSsnErrorStatsTable
that was incremented when the last session failure occurred.
If the reason for failure is not found in the
iscsiInstSsnErrorStatsTable, the value { 0.0 } is
used instead."
::= { iscsiInstanceAttributesEntry 11 }
iscsiInstLastSsnRmtNodeName OBJECT-TYPE
SYNTAX IscsiName
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The iSCSI name of the remote node from the failed
session."
::= { iscsiInstanceAttributesEntry 12 }
iscsiInstDiscontinuityTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of SysUpTime on the most recent occasion
at which any one or more of this instance's counters
suffered a discontinuity.
If no such discontinuities have occurred since the last
re-initialization of the local management subsystem,
then this object contains a zero value."
::= { iscsiInstanceAttributesEntry 13 }
-- Instance Session Failure Stats Table
iscsiInstanceSsnErrorStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF IscsiInstanceSsnErrorStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Statistics regarding the occurrences of error types
that result in a session failure."
::= { iscsiInstance 2 }
iscsiInstanceSsnErrorStatsEntry OBJECT-TYPE
SYNTAX IscsiInstanceSsnErrorStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (row) containing management information applicable
to a particular iSCSI instance."
AUGMENTS { iscsiInstanceAttributesEntry }
::= { iscsiInstanceSsnErrorStatsTable 1 }
IscsiInstanceSsnErrorStatsEntry ::= SEQUENCE {
iscsiInstSsnDigestErrors Counter32,
iscsiInstSsnCxnTimeoutErrors Counter32,
iscsiInstSsnFormatErrors Counter32
}
iscsiInstSsnDigestErrors OBJECT-TYPE
SYNTAX Counter32
UNITS "sessions"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The count of sessions that were failed due to receipt of
a PDU containing header or data digest errors. If this
counter has suffered a discontinuity, the time of the last
discontinuity is indicated in iscsiInstDiscontinuityTime."
REFERENCE
"RFC 3720, Section 6.7, Digest Errors"
::= { iscsiInstanceSsnErrorStatsEntry 1 }
iscsiInstSsnCxnTimeoutErrors OBJECT-TYPE
SYNTAX Counter32
UNITS "sessions"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The count of sessions that were failed due to a sequence
exceeding a time limit. If this counter has suffered a
discontinuity, the time of the last discontinuity
is indicated in iscsiInstDiscontinuityTime."
REFERENCE
"RFC 3720, Section 6.4, Connection Timeout Management"
::= { iscsiInstanceSsnErrorStatsEntry 2 }
iscsiInstSsnFormatErrors OBJECT-TYPE
SYNTAX Counter32
UNITS "sessions"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The count of sessions that were failed due to receipt of
a PDU that contained a format error. If this counter has
suffered a discontinuity, the time of the last discontinuity
is indicated in iscsiInstDiscontinuityTime."
REFERENCE
"RFC 3720, Section 6.6, Format Errors"
::= { iscsiInstanceSsnErrorStatsEntry 3 }
--**********************************************************************
iscsiPortal OBJECT IDENTIFIER ::= { iscsiObjects 2 }
-- Portal Attributes Table
iscsiPortalAttributesTable OBJECT-TYPE
SYNTAX SEQUENCE OF IscsiPortalAttributesEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of transport endpoints (using TCP or another transport
protocol) used by this iSCSI instance. An iSCSI instance may
use a portal to listen for incoming connections to its targets,
to initiate connections to other targets, or both."
::= { iscsiPortal 1 }
iscsiPortalAttributesEntry OBJECT-TYPE
SYNTAX IscsiPortalAttributesEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (row) containing management information applicable
to a particular portal instance."
INDEX { iscsiInstIndex, iscsiPortalIndex }
::= { iscsiPortalAttributesTable 1 }
IscsiPortalAttributesEntry ::= SEQUENCE {
iscsiPortalIndex Unsigned32,
iscsiPortalRowStatus RowStatus,
iscsiPortalRoles BITS,
iscsiPortalAddrType InetAddressType,
iscsiPortalAddr InetAddress,
iscsiPortalProtocol IscsiTransportProtocol,
iscsiPortalMaxRecvDataSegLength Unsigned32,
iscsiPortalPrimaryHdrDigest IscsiDigestMethod,
iscsiPortalPrimaryDataDigest IscsiDigestMethod,
iscsiPortalSecondaryHdrDigest IscsiDigestMethod,
iscsiPortalSecondaryDataDigest IscsiDigestMethod,
iscsiPortalRecvMarker TruthValue,
iscsiPortalStorageType StorageType
}
iscsiPortalIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An arbitrary integer used to uniquely identify a particular
transport endpoint within this iSCSI instance. This index
value must not be modified or reused by an agent unless a
reboot has occurred. An agent should attempt to keep this
value persistent across reboots."
::= { iscsiPortalAttributesEntry 1 }
iscsiPortalRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This field allows entries to be dynamically added and
removed from this table via SNMP. When adding a row to
this table, all non-Index/RowStatus objects must be set.
When the value of this object is 'active', the values of
the other objects in this table cannot be changed.
Rows may be discarded using RowStatus.
Note that creating a row in this table will typically
cause the agent to create one or more rows in
iscsiTgtPortalAttributesTable and/or
iscsiIntrPortalAttributesTable."
::= { iscsiPortalAttributesEntry 2 }
iscsiPortalRoles OBJECT-TYPE
SYNTAX BITS {
targetTypePortal(0),
initiatorTypePortal(1)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A portal can operate in one or both of two roles:
as a target portal and/or an initiator portal. If
the portal will operate in both roles, both bits
must be set.
This object will define a corresponding row that
will exist or must be created in the
iscsiTgtPortalAttributesTable, the
iscsiIntrPortalAttributesTable or both. If the
targetTypePortal bit is set, one or more corresponding
iscsiTgtPortalAttributesEntry rows will be found or
created. If the initiatorTypePortal bit is set,
one or more corresponding iscsiIntrPortalAttributesEntry
rows will be found or created. If both bits are set, one
or more corresponding rows will be found or created in
one of the above tables."
::= { iscsiPortalAttributesEntry 3 }
iscsiPortalAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The type of Internet Network Address contained in the
corresponding instance of the iscsiPortalAddr."
DEFVAL { ipv4 }
::= { iscsiPortalAttributesEntry 4 }
iscsiPortalAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The portal's Internet Network Address, of the type
specified by the object iscsiPortalAddrType. If
iscsiPortalAddrType has the value 'dns', this address
gets resolved to an IP address whenever a new iSCSI
connection is established using this portal."
::= { iscsiPortalAttributesEntry 5 }
iscsiPortalProtocol OBJECT-TYPE
SYNTAX IscsiTransportProtocol
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The portal's transport protocol."
DEFVAL { 6 } -- TCP
::= { iscsiPortalAttributesEntry 6 }
iscsiPortalMaxRecvDataSegLength OBJECT-TYPE
SYNTAX Unsigned32 (512..16777215)
UNITS "bytes"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum PDU length this portal can receive.
This may be constrained by hardware characteristics
and individual implementations may choose not to
allow this object to be changed."
REFERENCE
"RFC 3720, Section 12.12, MaxRecvDataSegmentLength"
DEFVAL { 8192 }
::= { iscsiPortalAttributesEntry 7 }
iscsiPortalPrimaryHdrDigest OBJECT-TYPE
SYNTAX IscsiDigestMethod
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The preferred header digest for this portal."
DEFVAL { crc32c }
::= { iscsiPortalAttributesEntry 8 }
iscsiPortalPrimaryDataDigest OBJECT-TYPE
SYNTAX IscsiDigestMethod
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The preferred data digest method for this portal."
DEFVAL { crc32c }
::= { iscsiPortalAttributesEntry 9 }
iscsiPortalSecondaryHdrDigest OBJECT-TYPE
SYNTAX IscsiDigestMethod
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An alternate header digest preference for this portal."
DEFVAL { noDigest }
::= { iscsiPortalAttributesEntry 10 }
iscsiPortalSecondaryDataDigest OBJECT-TYPE
SYNTAX IscsiDigestMethod
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An alternate data digest preference for this portal."
DEFVAL { noDigest }
::= { iscsiPortalAttributesEntry 11 }
iscsiPortalRecvMarker OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object indicates whether or not this portal will
request markers in its incoming data stream."
REFERENCE
"RFC 3720, Appendix A."
DEFVAL { false }
::= { iscsiPortalAttributesEntry 12 }
iscsiPortalStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The storage type for this row. Rows in this table that were
created through an external process may have a storage type of
readOnly or permanent.
Conceptual rows having the value 'permanent' need not
allow write access to any columnar objects in the row."
DEFVAL { nonVolatile }
::= { iscsiPortalAttributesEntry 13 }
--**********************************************************************
iscsiTargetPortal OBJECT IDENTIFIER ::= { iscsiObjects 3 }
-- Target Portal Attributes Table
iscsiTgtPortalAttributesTable OBJECT-TYPE
SYNTAX SEQUENCE OF IscsiTgtPortalAttributesEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of transport endpoints (using TCP or another transport
protocol) on which this iSCSI instance listens for incoming
connections to its targets."
::= { iscsiTargetPortal 1 }
iscsiTgtPortalAttributesEntry OBJECT-TYPE
SYNTAX IscsiTgtPortalAttributesEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (row) containing management information applicable
to a particular portal instance that is used to listen for
incoming connections to local targets. One or more rows in
this table is populated by the agent for each
iscsiPortalAttributesEntry row that has the bit
targetTypePortal set in its iscsiPortalRoles column."
INDEX { iscsiInstIndex, iscsiPortalIndex,
iscsiTgtPortalNodeIndexOrZero }
::= { iscsiTgtPortalAttributesTable 1 }
IscsiTgtPortalAttributesEntry ::= SEQUENCE {
iscsiTgtPortalNodeIndexOrZero Unsigned32,
iscsiTgtPortalPort InetPortNumber,
iscsiTgtPortalTag Unsigned32
}
iscsiTgtPortalNodeIndexOrZero OBJECT-TYPE
SYNTAX Unsigned32 (0..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An arbitrary integer used to uniquely identify a
particular node within an iSCSI instance present
on the local system.
For implementations where each {portal, node} tuple
can have a different portal tag, this value will
map to the iscsiNodeIndex.
For implementations where the portal tag is the
same for a given portal regardless of which node
is using the portal, the value 0 (zero) is used."
::= { iscsiTgtPortalAttributesEntry 1 }
iscsiTgtPortalPort OBJECT-TYPE
SYNTAX InetPortNumber (1..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The portal's transport protocol port number on which the
portal listens for incoming iSCSI connections when the
portal is used as a target portal. This object's storage
type is specified in iscsiPortalStorageType."
::= { iscsiTgtPortalAttributesEntry 2 }
iscsiTgtPortalTag OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The portal's aggregation tag when the portal is used as
a target portal. Multiple-connection sessions may
be aggregated over portals sharing an identical
aggregation tag. This object's storage type is
specified in iscsiPortalStorageType."
REFERENCE
"RFC 3720, Section 3.4.1, iSCSI Architectural Model"
::= { iscsiTgtPortalAttributesEntry 3 }
--**********************************************************************
iscsiInitiatorPortal OBJECT IDENTIFIER ::= { iscsiObjects 4 }
-- Initiator Portal Attributes Table
iscsiIntrPortalAttributesTable OBJECT-TYPE
SYNTAX SEQUENCE OF IscsiIntrPortalAttributesEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of Internet Network Addresses (using TCP or another
transport protocol) from which this iSCSI instance may
initiate connections to other targets."
::= { iscsiInitiatorPortal 1 }
iscsiIntrPortalAttributesEntry OBJECT-TYPE
SYNTAX IscsiIntrPortalAttributesEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (row) containing management information applicable
to a particular portal instance that is used to initiate
connections to iSCSI targets. One or more rows in
this table is populated by the agent for each
iscsiPortalAttributesEntry row that has the bit
initiatorTypePortal set in its iscsiPortalRoles column."
INDEX { iscsiInstIndex, iscsiPortalIndex,
iscsiIntrPortalNodeIndexOrZero }
::= { iscsiIntrPortalAttributesTable 1 }
IscsiIntrPortalAttributesEntry ::= SEQUENCE {
iscsiIntrPortalNodeIndexOrZero Unsigned32,
iscsiIntrPortalTag Unsigned32
}
iscsiIntrPortalNodeIndexOrZero OBJECT-TYPE
SYNTAX Unsigned32 (0..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An arbitrary integer used to uniquely identify a
particular node within an iSCSI instance present
on the local system.
For implementations where each {portal, node} tuple
can have a different portal tag, this value will
map to the iscsiNodeIndex.
For implementations where the portal tag is the
same for a given portal regardless of which node
is using the portal, the value 0 (zero) is used."
::= { iscsiIntrPortalAttributesEntry 1 }
iscsiIntrPortalTag OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The portal's aggregation tag when the portal is used as
an initiator portal. Multiple-connection sessions may
be aggregated over portals sharing an identical
aggregation tag. This object's storage type is
specified in iscsiPortalStorageType."
REFERENCE
"RFC 3720, Section 3.4.1, iSCSI Architectural Model"
::= { iscsiIntrPortalAttributesEntry 2 }
--**********************************************************************
iscsiNode OBJECT IDENTIFIER ::= { iscsiObjects 5 }
-- Node Attributes Table
iscsiNodeAttributesTable OBJECT-TYPE
SYNTAX SEQUENCE OF IscsiNodeAttributesEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of iSCSI nodes belonging to each iSCSI instance
present on the local system. An iSCSI node can act as
an initiator, a target, or both."
::= { iscsiNode 1 }
iscsiNodeAttributesEntry OBJECT-TYPE
SYNTAX IscsiNodeAttributesEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (row) containing management information applicable
to a particular iSCSI node."
INDEX { iscsiInstIndex, iscsiNodeIndex }
::= { iscsiNodeAttributesTable 1 }
IscsiNodeAttributesEntry ::= SEQUENCE {
iscsiNodeIndex Unsigned32,
iscsiNodeName IscsiName,
iscsiNodeAlias SnmpAdminString,
iscsiNodeRoles BITS,
iscsiNodeTransportType RowPointer,
iscsiNodeInitialR2T TruthValue,
iscsiNodeImmediateData TruthValue,
iscsiNodeMaxOutstandingR2T Unsigned32,
iscsiNodeFirstBurstLength Unsigned32,
iscsiNodeMaxBurstLength Unsigned32,
iscsiNodeMaxConnections Unsigned32,
iscsiNodeDataSequenceInOrder TruthValue,
iscsiNodeDataPDUInOrder TruthValue,
iscsiNodeDefaultTime2Wait Unsigned32,
iscsiNodeDefaultTime2Retain Unsigned32,
iscsiNodeErrorRecoveryLevel Unsigned32,
iscsiNodeDiscontinuityTime TimeStamp,
iscsiNodeStorageType StorageType
}
iscsiNodeIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An arbitrary integer used to uniquely identify a particular
node within an iSCSI instance. This index value must not be
modified or reused by an agent unless a reboot has occurred.
An agent should attempt to keep this value persistent across
reboots."
::= { iscsiNodeAttributesEntry 1 }
iscsiNodeName OBJECT-TYPE
SYNTAX IscsiName
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This node's iSCSI name, which is independent of the location
of the node, and can be resolved into a set of addresses
through various discovery services."
::= { iscsiNodeAttributesEntry 2 }
iscsiNodeAlias OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A character string that is a human-readable name or
description of the iSCSI node. If configured, this alias
may be communicated to the initiator or target node at
the remote end of the connection during a Login Request
or Response message. This string is not used as an
identifier, but can be displayed by the system's user
interface in a list of initiators and/or targets to
which it is connected.
If no alias exists, the value is a zero-length string."
REFERENCE
"RFC 3720, Section 12.6, TargetAlias, 12.7, InitiatorAlias"
::= { iscsiNodeAttributesEntry 3 }
iscsiNodeRoles OBJECT-TYPE
SYNTAX BITS {
targetTypeNode(0),
initiatorTypeNode(1)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A node can operate in one or both of two roles:
a target role and/or an initiator role. If the node
will operate in both roles, both bits must be set.
This object will also define the corresponding rows that
will exist in the iscsiTargetAttributesTable, the
iscsiInitiatorAttributesTable or both. If the
targetTypeNode bit is set, there will be a corresponding
iscsiTargetAttributesEntry. If the initiatorTypeNode bit
is set, there will be a corresponding
iscsiInitiatorAttributesEntry. If both bits are set,
there will be a corresponding iscsiTgtPortalAttributesEntry
and iscsiPortalAttributesEntry."
::= { iscsiNodeAttributesEntry 4 }
iscsiNodeTransportType OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A pointer to the corresponding row in the appropriate
table for this SCSI transport, thereby allowing management
stations to locate the SCSI-level device that is represented
by this iscsiNode. For example, it will usually point to the
corresponding scsiTrnspt object in the SCSI MIB module.
If no corresponding row exists, the value 0.0 must be
used to indicate this."
REFERENCE
"SCSI-MIB"
::= { iscsiNodeAttributesEntry 5 }
iscsiNodeInitialR2T OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the InitialR2T preference for this
node:
true = YES,
false = will try to negotiate NO, will accept YES "
REFERENCE
"RFC 3720, Section 12.10, InitialR2T"
::= { iscsiNodeAttributesEntry 6 }
iscsiNodeImmediateData OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object indicates ImmediateData preference for this
node:
true = YES (but will accept NO),
false = NO "
REFERENCE
"RFC 3720, Section 12.11, ImmediateData"
DEFVAL { true }
::= { iscsiNodeAttributesEntry 7 }
iscsiNodeMaxOutstandingR2T OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
UNITS "R2Ts"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Maximum number of outstanding requests-to-transmit (R2Ts)
allowed per iSCSI task."
REFERENCE
"RFC 3720, Section 12.17, MaxOutstandingR2T"
DEFVAL { 1 }
::= { iscsiNodeAttributesEntry 8 }
iscsiNodeFirstBurstLength OBJECT-TYPE
SYNTAX Unsigned32 (512..16777215)
UNITS "bytes"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The maximum length (bytes) supported for unsolicited data
to/from this node."
REFERENCE
"RFC 3720, Section 12.14, FirstBurstLength"
DEFVAL { 65536 }
::= { iscsiNodeAttributesEntry 9 }
iscsiNodeMaxBurstLength OBJECT-TYPE
SYNTAX Unsigned32 (512..16777215)
UNITS "bytes"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The maximum number of bytes that can be sent within
a single sequence of Data-In or Data-Out PDUs."
REFERENCE
"RFC 3720, Section 12.13, MaxBurstLength"
DEFVAL { 262144 }
::= { iscsiNodeAttributesEntry 10 }
iscsiNodeMaxConnections OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
UNITS "connections"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The maximum number of connections allowed in each
session to and/or from this node."
REFERENCE
"RFC 3720, Section 12.2, MaxConnections"
DEFVAL { 1 }
::= { iscsiNodeAttributesEntry 11 }
iscsiNodeDataSequenceInOrder OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The DataSequenceInOrder preference of this node.
False (=No) indicates that iSCSI data PDU sequences may
be transferred in any order. True (=Yes) indicates that
data PDU sequences must be transferred using
continuously increasing offsets, except during
error recovery."
REFERENCE
"RFC 3720, Section 12.19, DataSequenceInOrder"
DEFVAL { true }
::= { iscsiNodeAttributesEntry 12 }
iscsiNodeDataPDUInOrder OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The DataPDUInOrder preference of this node.
False (=No) indicates that iSCSI data PDUs within sequences
may be in any order. True (=Yes) indicates that data PDUs
within sequences must be at continuously increasing
addresses, with no gaps or overlay between PDUs."
REFERENCE
"RFC 3720, Section 12.18, DataPDUInOrder"
DEFVAL { true }
::= { iscsiNodeAttributesEntry 13 }
iscsiNodeDefaultTime2Wait OBJECT-TYPE
SYNTAX Unsigned32 (0..3600)
UNITS "seconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The DefaultTime2Wait preference of this node. This is the
minimum time, in seconds, to wait before attempting an
explicit/implicit logout or active iSCSI task reassignment
after an unexpected connection termination or a connection
reset."
REFERENCE
"RFC 3720, Section 12.15, DefaultTime2Wait"
DEFVAL { 2 }
::= { iscsiNodeAttributesEntry 14 }
iscsiNodeDefaultTime2Retain OBJECT-TYPE
SYNTAX Unsigned32 (0..3600)
UNITS "seconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The DefaultTime2Retain preference of this node. This is
the maximum time, in seconds after an initial wait
(Time2Wait), before which an active iSCSI task reassignment
is still possible after an unexpected connection termination
or a connection reset."
REFERENCE
"RFC 3720, Section 12.16, DefaultTime2Retain"
DEFVAL { 20 }
::= { iscsiNodeAttributesEntry 15 }
iscsiNodeErrorRecoveryLevel OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The ErrorRecoveryLevel preference of this node.
Currently, only 0-2 are valid.
This object is designed to accommodate future error recovery
levels.
Higher error recovery levels imply support in addition to
support for the lower error level functions. In other words,
error level 2 implies support for levels 0-1, since those
functions are subsets of error level 2."
REFERENCE
"RFC 3720, Section 12.20, ErrorRecoveryLevel"
DEFVAL { 0 }
::= { iscsiNodeAttributesEntry 16 }
iscsiNodeDiscontinuityTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of SysUpTime on the most recent occasion
at which any one or more of this node's counters
suffered a discontinuity.
If no such discontinuities have occurred since the last
re-initialization of the local management subsystem,
then this object contains a zero value."
::= { iscsiNodeAttributesEntry 17 }
iscsiNodeStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The storage type for all read-write objects within this
row. Rows in this table are always created via an
external process, and may have a storage type of readOnly
or permanent. Conceptual rows having the value 'permanent'
need not allow write access to any columnar objects in
the row.
If this object has the value 'volatile', modifications
to read-write objects in this row are not persistent
across reboots. If this object has the value
'nonVolatile', modifications to objects in this row
are persistent.
An implementation may choose to allow this object
to be set to either 'nonVolatile' or 'volatile',
allowing the management application to choose this
behavior."
DEFVAL { volatile }
::= { iscsiNodeAttributesEntry 18 }
--**********************************************************************
iscsiTarget OBJECT IDENTIFIER ::= { iscsiObjects 6 }
-- Target Attributes Table
iscsiTargetAttributesTable OBJECT-TYPE
SYNTAX SEQUENCE OF IscsiTargetAttributesEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of iSCSI nodes that can take on a target role,
belonging to each iSCSI instance present on the local
system."
::= { iscsiTarget 1 }
iscsiTargetAttributesEntry OBJECT-TYPE
SYNTAX IscsiTargetAttributesEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (row) containing management information applicable
to a particular node that can take on a target role."
INDEX { iscsiInstIndex, iscsiNodeIndex }
::= { iscsiTargetAttributesTable 1 }
IscsiTargetAttributesEntry ::= SEQUENCE {
iscsiTgtLoginFailures Counter32,
iscsiTgtLastFailureTime TimeStamp,
iscsiTgtLastFailureType AutonomousType,
iscsiTgtLastIntrFailureName IscsiName,
iscsiTgtLastIntrFailureAddrType InetAddressType,
iscsiTgtLastIntrFailureAddr InetAddress
}
iscsiTgtLoginFailures OBJECT-TYPE
SYNTAX Counter32
UNITS "failed login attempts"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of times a login attempt to this
local target has failed.
If this counter has suffered a discontinuity, the time of the
last discontinuity is indicated in iscsiNodeDiscontinuityTime."
REFERENCE
"RFC 3720, Section 10.13.5, Status-Class and Status-Detail"
::= { iscsiTargetAttributesEntry 1 }
iscsiTgtLastFailureTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The timestamp of the most recent failure of a login attempt
to this target. A value of zero indicates that no such
failures have occurred since the last system boot."
::= { iscsiTargetAttributesEntry 2 }
iscsiTgtLastFailureType OBJECT-TYPE
SYNTAX AutonomousType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The type of the most recent failure of a login attempt
to this target, represented as the OID of the counter
object in iscsiTargetLoginStatsTable for which the
relevant instance was incremented. A value of 0.0
indicates a type that is not represented by any of
the counters in iscsiTargetLoginStatsTable."
::= { iscsiTargetAttributesEntry 3 }
iscsiTgtLastIntrFailureName OBJECT-TYPE
SYNTAX IscsiName
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The iSCSI name of the initiator that failed the last
login attempt."
::= { iscsiTargetAttributesEntry 4 }
iscsiTgtLastIntrFailureAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The type of Internet Network Address contained in the
corresponding instance of the iscsiTgtLastIntrFailureAddr.
The value 'dns' is not allowed."
::= { iscsiTargetAttributesEntry 5 }
iscsiTgtLastIntrFailureAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An Internet Network Address, of the type specified by
the object iscsiTgtLastIntrFailureAddrType, giving the
host address of the initiator that failed the last login
attempt."
::= { iscsiTargetAttributesEntry 6 }
-- Target Login Stats Table
iscsiTargetLoginStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF IscsiTargetLoginStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of counters that keep a record of the results
of initiators' login attempts to this target."
::= { iscsiTarget 2 }
iscsiTargetLoginStatsEntry OBJECT-TYPE
SYNTAX IscsiTargetLoginStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (row) containing counters for each result of
a login attempt to this target."
AUGMENTS { iscsiTargetAttributesEntry }
::= { iscsiTargetLoginStatsTable 1 }
IscsiTargetLoginStatsEntry ::= SEQUENCE {
iscsiTgtLoginAccepts Counter32,
iscsiTgtLoginOtherFails Counter32,
iscsiTgtLoginRedirects Counter32,
iscsiTgtLoginAuthorizeFails Counter32,
iscsiTgtLoginAuthenticateFails Counter32,
iscsiTgtLoginNegotiateFails Counter32
}
iscsiTgtLoginAccepts OBJECT-TYPE
SYNTAX Counter32
UNITS "successful logins"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The count of Login Response PDUs with status
0x0000, Accept Login, transmitted by this
target.
If this counter has suffered a discontinuity, the time of the
last discontinuity is indicated in iscsiNodeDiscontinuityTime."
REFERENCE
"RFC 3720, Section 10.13.5, Status-Class and Status-Detail"
::= { iscsiTargetLoginStatsEntry 1 }
iscsiTgtLoginOtherFails OBJECT-TYPE
SYNTAX Counter32
UNITS "failed logins"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of Login Response PDUs that were transmitted
by this target and that were not counted by any other
object in the row.
If this counter has suffered a discontinuity, the time of the
last discontinuity is indicated in iscsiNodeDiscontinuityTime."
REFERENCE
"RFC 3720, Section 10.13.5, Status-Class and Status-Detail"
::= { iscsiTargetLoginStatsEntry 2 }
iscsiTgtLoginRedirects OBJECT-TYPE
SYNTAX Counter32
UNITS "redirected logins"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The count of Login Response PDUs with status class 0x01,
Redirection, transmitted by this target.
If this counter has suffered a discontinuity, the time of the
last discontinuity is indicated in iscsiNodeDiscontinuityTime."
REFERENCE
"RFC 3720, Section 10.13.5, Status-Class and Status-Detail"
::= { iscsiTargetLoginStatsEntry 3 }
iscsiTgtLoginAuthorizeFails OBJECT-TYPE
SYNTAX Counter32
UNITS "failed logins"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The count of Login Response PDUs with status 0x0202,
Forbidden Target, transmitted by this target.
If this counter is incremented, an iscsiTgtLoginFailure
notification should be generated.
If this counter has suffered a discontinuity, the time of the
last discontinuity is indicated in iscsiNodeDiscontinuityTime."
REFERENCE
"RFC 3720, Section 10.13.5, Status-Class and Status-Detail"
::= { iscsiTargetLoginStatsEntry 4 }
iscsiTgtLoginAuthenticateFails OBJECT-TYPE
SYNTAX Counter32
UNITS "failed logins"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The count of Login Response PDUs with status 0x0201,
Authentication Failed, transmitted by this target.
If this counter is incremented, an iscsiTgtLoginFailure
notification should be generated.
If this counter has suffered a discontinuity, the time of the
last discontinuity is indicated in iscsiNodeDiscontinuityTime."
REFERENCE
"RFC 3720, Section 10.13.5, Status-Class and Status-Detail"
::= { iscsiTargetLoginStatsEntry 5 }
iscsiTgtLoginNegotiateFails OBJECT-TYPE
SYNTAX Counter32
UNITS "failed logins"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times a target has effectively refused a
login because the parameter negotiation failed.
If this counter is incremented, an iscsiTgtLoginFailure
notification should be generated.
If this counter has suffered a discontinuity, the time of the
last discontinuity is indicated in iscsiNodeDiscontinuityTime."
::= { iscsiTargetLoginStatsEntry 6 }
-- Target Logout Stats Table
iscsiTargetLogoutStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF IscsiTargetLogoutStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"When a target receives a Logout command, it responds
with a Logout Response that carries a status code.
This table contains counters for both normal and
abnormal logout requests received by this target."
::= { iscsiTarget 3 }
iscsiTargetLogoutStatsEntry OBJECT-TYPE
SYNTAX IscsiTargetLogoutStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (row) containing counters of Logout Response
PDUs that were received by this target."
AUGMENTS { iscsiTargetAttributesEntry }
::= { iscsiTargetLogoutStatsTable 1 }
IscsiTargetLogoutStatsEntry ::= SEQUENCE {
iscsiTgtLogoutNormals Counter32,
iscsiTgtLogoutOthers Counter32
}
iscsiTgtLogoutNormals OBJECT-TYPE
SYNTAX Counter32
UNITS "normal logouts"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The count of Logout Command PDUs received by this target,
with reason code 0 (closes the session).
If this counter has suffered a discontinuity, the time of the
last discontinuity is indicated in iscsiNodeDiscontinuityTime."
REFERENCE
"RFC 3720, Section 10.14.1, Reason Code"
::= { iscsiTargetLogoutStatsEntry 1 }
iscsiTgtLogoutOthers OBJECT-TYPE
SYNTAX Counter32
UNITS "abnormal logouts"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The count of Logout Command PDUs received by this target,
with any reason code other than 0.
If this counter has suffered a discontinuity, the time of the
last discontinuity is indicated in iscsiNodeDiscontinuityTime."
REFERENCE
"RFC 3720, Section 10.14.1, Reason Code"
::= { iscsiTargetLogoutStatsEntry 2 }
--**********************************************************************
iscsiTgtAuthorization OBJECT IDENTIFIER ::= { iscsiObjects 7 }
-- Target Authorization Attributes Table
iscsiTgtAuthAttributesTable OBJECT-TYPE
SYNTAX SEQUENCE OF IscsiTgtAuthAttributesEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of initiator identities that are authorized to
access each target node within each iSCSI instance
present on the local system."
::= { iscsiTgtAuthorization 1 }
iscsiTgtAuthAttributesEntry OBJECT-TYPE
SYNTAX IscsiTgtAuthAttributesEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (row) containing management information
applicable to a particular target node's authorized
initiator identity."
INDEX { iscsiInstIndex, iscsiNodeIndex, iscsiTgtAuthIndex }
::= { iscsiTgtAuthAttributesTable 1 }
IscsiTgtAuthAttributesEntry ::= SEQUENCE {
iscsiTgtAuthIndex Unsigned32,
iscsiTgtAuthRowStatus RowStatus,
iscsiTgtAuthIdentity RowPointer,
iscsiTgtAuthStorageType StorageType
}
iscsiTgtAuthIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An arbitrary integer used to uniquely identify a particular
target's authorized initiator identity within an iSCSI
instance present on the local system. This index value must
not be modified or reused by an agent unless a reboot has
occurred. An agent should attempt to keep this value
persistent across reboots."
::= { iscsiTgtAuthAttributesEntry 1 }
iscsiTgtAuthRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This field allows entries to be dynamically added and
removed from this table via SNMP. When adding a row to
this table, all non-Index/RowStatus objects must be set.
When the value of this object is 'active', the values of
the other objects in this table cannot be changed.
Rows may be discarded using RowStatus."
::= { iscsiTgtAuthAttributesEntry 2 }
iscsiTgtAuthIdentity OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A pointer to the corresponding user entry in the IPS-AUTH
MIB module that will be allowed to access this iSCSI target."
REFERENCE
"IPS-AUTH MIB, RFC 4545"
::= { iscsiTgtAuthAttributesEntry 3 }
iscsiTgtAuthStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The storage type for this row. Rows in this table that were
created through an external process may have a storage type of
readOnly or permanent.
Conceptual rows having the value 'permanent' need not
allow write access to any columnar objects in the row."
DEFVAL { nonVolatile }
::= { iscsiTgtAuthAttributesEntry 4 }
--**********************************************************************
iscsiInitiator OBJECT IDENTIFIER ::= { iscsiObjects 8 }
-- Initiator Attributes Table
iscsiInitiatorAttributesTable OBJECT-TYPE
SYNTAX SEQUENCE OF IscsiInitiatorAttributesEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of iSCSI nodes that can take on an initiator
role, belonging to each iSCSI instance present on
the local system."
::= { iscsiInitiator 1 }
iscsiInitiatorAttributesEntry OBJECT-TYPE
SYNTAX IscsiInitiatorAttributesEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (row) containing management information
applicable to a particular iSCSI node that has
initiator capabilities."
INDEX { iscsiInstIndex, iscsiNodeIndex }
::= { iscsiInitiatorAttributesTable 1 }
IscsiInitiatorAttributesEntry ::= SEQUENCE {
iscsiIntrLoginFailures Counter32,
iscsiIntrLastFailureTime TimeStamp,
iscsiIntrLastFailureType AutonomousType,
iscsiIntrLastTgtFailureName IscsiName,
iscsiIntrLastTgtFailureAddrType InetAddressType,
iscsiIntrLastTgtFailureAddr InetAddress
}
iscsiIntrLoginFailures OBJECT-TYPE
SYNTAX Counter32
UNITS "failed logins"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of times a login attempt from
this local initiator has failed.
If this counter has suffered a discontinuity, the time of the
last discontinuity is indicated in iscsiNodeDiscontinuityTime."
REFERENCE
"RFC 3720, Section 10.13.5, Status-Class and Status-Detail"
::= { iscsiInitiatorAttributesEntry 1 }
iscsiIntrLastFailureTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The timestamp of the most recent failure of a login attempt
from this initiator. A value of zero indicates that no such
failures have occurred since the last system boot."
::= { iscsiInitiatorAttributesEntry 2 }
iscsiIntrLastFailureType OBJECT-TYPE
SYNTAX AutonomousType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The type of the most recent failure of a login attempt
from this initiator, represented as the OID of the counter
object in iscsiInitiatorLoginStatsTable for which the
relevant instance was incremented. A value of 0.0
indicates a type that is not represented by any of
the counters in iscsiInitiatorLoginStatsTable."
::= { iscsiInitiatorAttributesEntry 3 }
iscsiIntrLastTgtFailureName OBJECT-TYPE
SYNTAX IscsiName
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A UTF-8 string giving the name of the target that failed
the last login attempt."
::= { iscsiInitiatorAttributesEntry 4 }
iscsiIntrLastTgtFailureAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The type of Internet Network Address contained in the
corresponding instance of the iscsiIntrLastTgtFailureAddr.
The value 'dns' is not allowed."
::= { iscsiInitiatorAttributesEntry 5 }
iscsiIntrLastTgtFailureAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An Internet Network Address, of the type specified by the
object iscsiIntrLastTgtFailureAddrType, giving the host
address of the target that failed the last login attempt."
::= { iscsiInitiatorAttributesEntry 6 }
-- Initiator Login Stats Table
iscsiInitiatorLoginStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF IscsiInitiatorLoginStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of counters which keep track of the results of
this initiator's login attempts."
::= { iscsiInitiator 2 }
iscsiInitiatorLoginStatsEntry OBJECT-TYPE
SYNTAX IscsiInitiatorLoginStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (row) containing counters of each result
of this initiator's login attempts."
AUGMENTS { iscsiInitiatorAttributesEntry }
::= { iscsiInitiatorLoginStatsTable 1 }
IscsiInitiatorLoginStatsEntry ::= SEQUENCE {
iscsiIntrLoginAcceptRsps Counter32,
iscsiIntrLoginOtherFailRsps Counter32,
iscsiIntrLoginRedirectRsps Counter32,
iscsiIntrLoginAuthFailRsps Counter32,
iscsiIntrLoginAuthenticateFails Counter32,
iscsiIntrLoginNegotiateFails Counter32
}
iscsiIntrLoginAcceptRsps OBJECT-TYPE
SYNTAX Counter32
UNITS "successful logins"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The count of Login Response PDUs with status
0x0000, Accept Login, received by this initiator.
If this counter has suffered a discontinuity, the time of the
last discontinuity is indicated in iscsiNodeDiscontinuityTime."
REFERENCE
"RFC 3720, Section 10.13.5, Status-Class and Status-Detail"
::= { iscsiInitiatorLoginStatsEntry 1 }
iscsiIntrLoginOtherFailRsps OBJECT-TYPE
SYNTAX Counter32
UNITS "failed logins"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The count of Login Response PDUs received by this
initiator with any status code not counted in the
objects below.
If this counter has suffered a discontinuity, the time of the
last discontinuity is indicated in iscsiNodeDiscontinuityTime."
REFERENCE
"RFC 3720, Section 10.13.5, Status-Class and Status-Detail"
::= { iscsiInitiatorLoginStatsEntry 2 }
iscsiIntrLoginRedirectRsps OBJECT-TYPE
SYNTAX Counter32
UNITS "failed logins"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The count of Login Response PDUs with status class 0x01,
Redirection, received by this initiator.
If this counter has suffered a discontinuity, the time of the
last discontinuity is indicated in iscsiNodeDiscontinuityTime."
REFERENCE
"RFC 3720, Section 10.13.5, Status-Class and Status-Detail"
::= { iscsiInitiatorLoginStatsEntry 3 }
iscsiIntrLoginAuthFailRsps OBJECT-TYPE
SYNTAX Counter32
UNITS "failed logins"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The count of Login Response PDUs with status class 0x201,
Authentication Failed, received by this initiator.
If this counter has suffered a discontinuity, the time of the
last discontinuity is indicated in iscsiNodeDiscontinuityTime."
REFERENCE
"RFC 3720, Section 10.13.5, Status-Class and Status-Detail"
::= { iscsiInitiatorLoginStatsEntry 4 }
iscsiIntrLoginAuthenticateFails OBJECT-TYPE
SYNTAX Counter32
UNITS "failed logins"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times the initiator has aborted a
login because the target could not be authenticated.
No response is generated.
If this counter is incremented, an iscsiIntrLoginFailure
notification should be generated.
If this counter has suffered a discontinuity, the time of the
last discontinuity is indicated in iscsiNodeDiscontinuityTime."
REFERENCE
"RFC 3720, Section 10.13.5, Status-Class and Status-Detail"
::= { iscsiInitiatorLoginStatsEntry 5 }
iscsiIntrLoginNegotiateFails OBJECT-TYPE
SYNTAX Counter32
UNITS "failed logins"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times the initiator has aborted a
login because parameter negotiation with the target
failed.
No response is generated.
If this counter is incremented, an iscsiIntrLoginFailure
notification should be generated.
If this counter has suffered a discontinuity, the time of the
last discontinuity is indicated in iscsiNodeDiscontinuityTime."
REFERENCE
"RFC 3720, Section 6.10, Negotiation Failures"
::= { iscsiInitiatorLoginStatsEntry 6 }
-- Initiator Logout Stats Table
iscsiInitiatorLogoutStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF IscsiInitiatorLogoutStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"When an initiator attempts to send a Logout command, the target
responds with a Logout Response that carries a status code.
This table contains a list of counters of Logout Response
PDUs of each status code that was received by each
initiator belonging to this iSCSI instance present on this
system."
::= { iscsiInitiator 3 }
iscsiInitiatorLogoutStatsEntry OBJECT-TYPE
SYNTAX IscsiInitiatorLogoutStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (row) containing counters of Logout Response
PDUs of each status code that was generated by this
initiator."
AUGMENTS { iscsiInitiatorAttributesEntry }
::= { iscsiInitiatorLogoutStatsTable 1 }
IscsiInitiatorLogoutStatsEntry ::= SEQUENCE {
iscsiIntrLogoutNormals Counter32,
iscsiIntrLogoutOthers Counter32
}
iscsiIntrLogoutNormals OBJECT-TYPE
SYNTAX Counter32
UNITS "normal logouts"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The count of Logout Command PDUs generated by this initiator
with reason code 0 (closes the session).
If this counter has suffered a discontinuity, the time of the
last discontinuity is indicated in iscsiNodeDiscontinuityTime."
REFERENCE
"RFC 3720, Section 10.14.1, Reason Code"
::= { iscsiInitiatorLogoutStatsEntry 1 }
iscsiIntrLogoutOthers OBJECT-TYPE
SYNTAX Counter32
UNITS "abnormal logouts"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The count of Logout Command PDUs generated by this initiator
with any status code other than 0.
If this counter has suffered a discontinuity, the time of the
last discontinuity is indicated in iscsiNodeDiscontinuityTime."
REFERENCE
"RFC 3720, Section 10.14.1, Reason Code"
::= { iscsiInitiatorLogoutStatsEntry 2 }
--**********************************************************************
iscsiIntrAuthorization OBJECT IDENTIFIER ::= { iscsiObjects 9 }
-- Initiator Authorization Attributes Table
iscsiIntrAuthAttributesTable OBJECT-TYPE
SYNTAX SEQUENCE OF IscsiIntrAuthAttributesEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of target identities that each initiator
on the local system may access."
::= { iscsiIntrAuthorization 1 }
iscsiIntrAuthAttributesEntry OBJECT-TYPE
SYNTAX IscsiIntrAuthAttributesEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (row) containing management information applicable
to a particular initiator node's authorized target identity."
INDEX { iscsiInstIndex, iscsiNodeIndex, iscsiIntrAuthIndex }
::= { iscsiIntrAuthAttributesTable 1 }
IscsiIntrAuthAttributesEntry ::= SEQUENCE {
iscsiIntrAuthIndex Unsigned32,
iscsiIntrAuthRowStatus RowStatus,
iscsiIntrAuthIdentity RowPointer,
iscsiIntrAuthStorageType StorageType
}
iscsiIntrAuthIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An arbitrary integer used to uniquely identify a
particular initiator node's authorized target
identity within an iSCSI instance present on the
local system. This index value must not be modified
or reused by an agent unless a reboot has occurred.
An agent should attempt to keep this value persistent
across reboots."
::= { iscsiIntrAuthAttributesEntry 1 }
iscsiIntrAuthRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This field allows entries to be dynamically added and
removed from this table via SNMP. When adding a row to
this table, all non-Index/RowStatus objects must be set.
When the value of this object is 'active', the values of
the other objects in this table cannot be changed.
Rows may be discarded using RowStatus."
::= { iscsiIntrAuthAttributesEntry 2 }
iscsiIntrAuthIdentity OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A pointer to the corresponding user entry in the IPS-AUTH
MIB module to which this initiator node should attempt to
establish an iSCSI session."
REFERENCE
"IPS-AUTH MIB, RFC 4545"
::= { iscsiIntrAuthAttributesEntry 3 }
iscsiIntrAuthStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The storage type for this row. Rows in this table that were
created through an external process may have a storage type of
readOnly or permanent.
Conceptual rows having the value 'permanent' need not
allow write access to any columnar objects in the row."
DEFVAL { nonVolatile }
::= { iscsiIntrAuthAttributesEntry 4 }
--**********************************************************************
iscsiSession OBJECT IDENTIFIER ::= { iscsiObjects 10 }
-- Session Attributes Table
iscsiSessionAttributesTable OBJECT-TYPE
SYNTAX SEQUENCE OF IscsiSessionAttributesEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of sessions belonging to each iSCSI instance
present on the system."
::= { iscsiSession 1 }
iscsiSessionAttributesEntry OBJECT-TYPE
SYNTAX IscsiSessionAttributesEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (row) containing management information applicable
to a particular session.
If this session is a discovery session that is not attached
to any particular node, the iscsiSsnNodeIndex will be zero.
Otherwise, the iscsiSsnNodeIndex will have the same value as
iscsiNodeIndex."
INDEX { iscsiInstIndex, iscsiSsnNodeIndex, iscsiSsnIndex }
::= { iscsiSessionAttributesTable 1 }
IscsiSessionAttributesEntry ::= SEQUENCE {
iscsiSsnNodeIndex Unsigned32,
iscsiSsnIndex Unsigned32,
iscsiSsnDirection INTEGER,
iscsiSsnInitiatorName IscsiName,
iscsiSsnTargetName IscsiName,
iscsiSsnTSIH Unsigned32,
iscsiSsnISID OCTET STRING,
iscsiSsnInitiatorAlias SnmpAdminString,
iscsiSsnTargetAlias SnmpAdminString,
iscsiSsnInitialR2T TruthValue,
iscsiSsnImmediateData TruthValue,
iscsiSsnType INTEGER,
iscsiSsnMaxOutstandingR2T Unsigned32,
iscsiSsnFirstBurstLength Unsigned32,
iscsiSsnMaxBurstLength Unsigned32,
iscsiSsnConnectionNumber Gauge32,
iscsiSsnAuthIdentity RowPointer,
iscsiSsnDataSequenceInOrder TruthValue,
iscsiSsnDataPDUInOrder TruthValue,
iscsiSsnErrorRecoveryLevel Unsigned32,
iscsiSsnDiscontinuityTime TimeStamp
}
iscsiSsnNodeIndex OBJECT-TYPE
SYNTAX Unsigned32 (0..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An arbitrary integer used to uniquely identify a
particular node within an iSCSI instance present
on the local system. For normal, non-discovery
sessions, this value will map to the iscsiNodeIndex.
For discovery sessions that do not have a node
associated, the value 0 (zero) is used."
::= { iscsiSessionAttributesEntry 1 }
iscsiSsnIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An arbitrary integer used to uniquely identify a
particular session within an iSCSI instance present
on the local system. An agent should attempt to
not reuse index values unless a reboot has occurred.
iSCSI sessions are destroyed during a reboot; rows
in this table are not persistent across reboots."
::= { iscsiSessionAttributesEntry 2 }
iscsiSsnDirection OBJECT-TYPE
SYNTAX INTEGER {
inboundSession(1),
outboundSession(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Direction of iSCSI session:
inboundSession - session is established from an external
initiator to a target within this iSCSI
instance.
outboundSession - session is established from an initiator
within this iSCSI instance to an external
target."
::= { iscsiSessionAttributesEntry 3 }
iscsiSsnInitiatorName OBJECT-TYPE
SYNTAX IscsiName
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If iscsiSsnDirection is Inbound, this object is a
UTF-8 string that will contain the name of the remote
initiator. If this session is a discovery session that
does not specify a particular initiator, this object
will contain a zero-length string.
If iscsiSsnDirection is Outbound, this object will
contain a zero-length string."
::= { iscsiSessionAttributesEntry 4 }
iscsiSsnTargetName OBJECT-TYPE
SYNTAX IscsiName
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If iscsiSsnDirection is Outbound, this object is a
UTF-8 string that will contain the name of the remote
target. If this session is a discovery session that
does not specify a particular target, this object will
contain a zero-length string.
If iscsiSsnDirection is Inbound, this object will
contain a zero-length string."
::= { iscsiSessionAttributesEntry 5 }
iscsiSsnTSIH OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The target-defined identification handle for this session."
REFERENCE
"RFC 3720, Section 10.12.6, TSIH"
::= { iscsiSessionAttributesEntry 6 }
iscsiSsnISID OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(6))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The initiator-defined portion of the iSCSI Session ID."
REFERENCE
"RFC 3720, Section 10.12.5, ISID"
::= { iscsiSessionAttributesEntry 7 }
iscsiSsnInitiatorAlias OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A UTF-8 string that gives the alias communicated by the
initiator end of the session during the login phase.
If no alias exists, the value is a zero-length string."
REFERENCE
"RFC 3720, Section 12.7, InitiatorAlias"
::= { iscsiSessionAttributesEntry 8 }
iscsiSsnTargetAlias OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A UTF-8 string that gives the alias communicated by the
target end of the session during the login phase.
If no alias exists, the value is a zero-length string."
REFERENCE
"RFC 3720, Section 12.6, TargetAlias"
::= { iscsiSessionAttributesEntry 9 }
iscsiSsnInitialR2T OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If set to true, indicates that the initiator must wait
for an R2T before sending to the target. If set to false,
the initiator may send data immediately, within limits set
by iscsiSsnFirstBurstLength and the expected data transfer
length of the request."
REFERENCE
"RFC 3720, Section 12.10, InitialR2T"
::= { iscsiSessionAttributesEntry 10 }
iscsiSsnImmediateData OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates whether the initiator and target have agreed to
support immediate data on this session."
REFERENCE
"RFC 3720, Section 12.11, ImmediateData"
::= { iscsiSessionAttributesEntry 11 }
iscsiSsnType OBJECT-TYPE
SYNTAX INTEGER {
normalSession(1),
discoverySession(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Type of iSCSI session:
normalSession - session is a normal iSCSI session
discoverySession - session is being used only for discovery."
REFERENCE
"RFC 3720, Section 12.21, SessionType"
::= { iscsiSessionAttributesEntry 12 }
iscsiSsnMaxOutstandingR2T OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
UNITS "R2Ts"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum number of outstanding requests-to-transmit
(R2Ts) per iSCSI task within this session."
REFERENCE
"RFC 3720, Section 12.17, MaxOutstandingR2T"
::= { iscsiSessionAttributesEntry 13 }
iscsiSsnFirstBurstLength OBJECT-TYPE
SYNTAX Unsigned32 (512..16777215)
UNITS "bytes"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum length supported for unsolicited data sent
within this session."
REFERENCE
"RFC 3720, Section 12.14, FirstBurstLength"
::= { iscsiSessionAttributesEntry 14 }
iscsiSsnMaxBurstLength OBJECT-TYPE
SYNTAX Unsigned32 (512..16777215)
UNITS "bytes"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum number of bytes that can be sent within
a single sequence of Data-In or Data-Out PDUs."
REFERENCE
"RFC 3720, Section 12.13, MaxBurstLength"
::= { iscsiSessionAttributesEntry 15 }
iscsiSsnConnectionNumber OBJECT-TYPE
SYNTAX Gauge32 (1..65535)
UNITS "connections"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of transport protocol connections that currently
belong to this session."
::= { iscsiSessionAttributesEntry 16 }
iscsiSsnAuthIdentity OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains a pointer to a row in the
IPS-AUTH MIB module that identifies the authentication
method being used on this session, as communicated
during the login phase."
REFERENCE
"IPS-AUTH MIB, RFC 4545"
::= { iscsiSessionAttributesEntry 17 }
iscsiSsnDataSequenceInOrder OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"False indicates that iSCSI data PDU sequences may
be transferred in any order. True indicates that
data PDU sequences must be transferred using
continuously increasing offsets, except during
error recovery."
REFERENCE
"RFC 3720, Section 12.19, DataSequenceInOrder"
::= { iscsiSessionAttributesEntry 18 }
iscsiSsnDataPDUInOrder OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"False indicates that iSCSI data PDUs within sequences
may be in any order. True indicates that data PDUs
within sequences must be at continuously increasing
addresses, with no gaps or overlay between PDUs.
Default is true."
REFERENCE
"RFC 3720, Section 12.18, DataPDUInOrder"
::= { iscsiSessionAttributesEntry 19 }
iscsiSsnErrorRecoveryLevel OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The level of error recovery negotiated between
the initiator and the target. Higher numbers
represent more detailed recovery schemes."
REFERENCE
"RFC 3720, Section 12.20, ErrorRecoveryLevel"
::= { iscsiSessionAttributesEntry 20 }
iscsiSsnDiscontinuityTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of SysUpTime on the most recent occasion
at which any one or more of this session's counters
suffered a discontinuity.
When a session is established, and this object is
created, it is initialized to the current value
of SysUpTime."
::= { iscsiSessionAttributesEntry 21 }
-- Session Stats Table
iscsiSessionStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF IscsiSessionStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of general iSCSI traffic counters for each of the
sessions present on the system."
::= { iscsiSession 2 }
iscsiSessionStatsEntry OBJECT-TYPE
SYNTAX IscsiSessionStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (row) containing general iSCSI traffic counters
for a particular session."
AUGMENTS { iscsiSessionAttributesEntry }
::= { iscsiSessionStatsTable 1 }
IscsiSessionStatsEntry ::= SEQUENCE {
iscsiSsnCmdPDUs Counter32,
iscsiSsnRspPDUs Counter32,
iscsiSsnTxDataOctets Counter64,
iscsiSsnRxDataOctets Counter64,
iscsiSsnLCTxDataOctets Counter32,
iscsiSsnLCRxDataOctets Counter32
}
iscsiSsnCmdPDUs OBJECT-TYPE
SYNTAX Counter32
UNITS "PDUs"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The count of Command PDUs transferred on this session.
If this counter has suffered a discontinuity, the time of the
last discontinuity is indicated in iscsiSsnDiscontinuityTime."
::= { iscsiSessionStatsEntry 1 }
iscsiSsnRspPDUs OBJECT-TYPE
SYNTAX Counter32
UNITS "PDUs"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The count of Response PDUs transferred on this session.
If this counter has suffered a discontinuity, the time of the
last discontinuity is indicated in iscsiSsnDiscontinuityTime."
::= { iscsiSessionStatsEntry 2 }
iscsiSsnTxDataOctets OBJECT-TYPE
SYNTAX Counter64
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The count of data octets that were transmitted by
the local iSCSI node on this session.
If this counter has suffered a discontinuity, the time of the
last discontinuity is indicated in iscsiSsnDiscontinuityTime."
::= { iscsiSessionStatsEntry 3 }
iscsiSsnRxDataOctets OBJECT-TYPE
SYNTAX Counter64
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The count of data octets that were received by
the local iSCSI node on this session.
If this counter has suffered a discontinuity, the time of the
last discontinuity is indicated in iscsiSsnDiscontinuityTime."
::= { iscsiSessionStatsEntry 4 }
iscsiSsnLCTxDataOctets OBJECT-TYPE
SYNTAX Counter32
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A Low Capacity shadow object of iscsiSsnTxDataOctets
for those systems that don't support Counter64.
If this counter has suffered a discontinuity, the time of the
last discontinuity is indicated in iscsiSsnDiscontinuityTime."
::= { iscsiSessionStatsEntry 5 }
iscsiSsnLCRxDataOctets OBJECT-TYPE
SYNTAX Counter32
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A Low Capacity shadow object of iscsiSsnRxDataOctets
for those systems that don't support Counter64.
If this counter has suffered a discontinuity, the time of the
last discontinuity is indicated in iscsiSsnDiscontinuityTime."
::= { iscsiSessionStatsEntry 6 }
-- Session Connection Error Stats Table
iscsiSessionCxnErrorStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF IscsiSessionCxnErrorStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of error counters for each of the sessions
present on this system."
::= { iscsiSession 3 }
iscsiSessionCxnErrorStatsEntry OBJECT-TYPE
SYNTAX IscsiSessionCxnErrorStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (row) containing error counters for
a particular session."
AUGMENTS { iscsiSessionAttributesEntry }
::= { iscsiSessionCxnErrorStatsTable 1 }
IscsiSessionCxnErrorStatsEntry ::= SEQUENCE {
iscsiSsnCxnDigestErrors Counter32,
iscsiSsnCxnTimeoutErrors Counter32
}
iscsiSsnCxnDigestErrors OBJECT-TYPE
SYNTAX Counter32
UNITS "PDUs"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The count of PDUs that were received on the session and
contained header or data digest errors.
If this counter has suffered a discontinuity, the time of the
last discontinuity is indicated in iscsiSsnDiscontinuityTime."
REFERENCE
"RFC 3720, Section 6.7, Digest Errors"
::= { iscsiSessionCxnErrorStatsEntry 1 }
iscsiSsnCxnTimeoutErrors OBJECT-TYPE
SYNTAX Counter32
UNITS "connections"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The count of connections within this session
that have been terminated due to timeout.
If this counter has suffered a discontinuity, the time of the
last discontinuity is indicated in iscsiSsnDiscontinuityTime."
REFERENCE
"RFC 3720, Section 6.4, Connection Timeout Management"
::= { iscsiSessionCxnErrorStatsEntry 2 }
--**********************************************************************
iscsiConnection OBJECT IDENTIFIER ::= { iscsiObjects 11 }
-- Connection Attributes Table
iscsiConnectionAttributesTable OBJECT-TYPE
SYNTAX SEQUENCE OF IscsiConnectionAttributesEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of connections belonging to each iSCSI instance
present on the system."
::= { iscsiConnection 1 }
iscsiConnectionAttributesEntry OBJECT-TYPE
SYNTAX IscsiConnectionAttributesEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (row) containing management information applicable
to a particular connection."
INDEX { iscsiInstIndex, iscsiSsnNodeIndex, iscsiSsnIndex,
iscsiCxnIndex }
::= { iscsiConnectionAttributesTable 1 }
IscsiConnectionAttributesEntry ::= SEQUENCE {
iscsiCxnIndex Unsigned32,
iscsiCxnCid Unsigned32,
iscsiCxnState INTEGER,
iscsiCxnAddrType InetAddressType,
iscsiCxnLocalAddr InetAddress,
iscsiCxnProtocol IscsiTransportProtocol,
iscsiCxnLocalPort InetPortNumber,
iscsiCxnRemoteAddr InetAddress,
iscsiCxnRemotePort InetPortNumber,
iscsiCxnMaxRecvDataSegLength Unsigned32,
iscsiCxnMaxXmitDataSegLength Unsigned32,
iscsiCxnHeaderIntegrity IscsiDigestMethod,
iscsiCxnDataIntegrity IscsiDigestMethod,
iscsiCxnRecvMarker TruthValue,
iscsiCxnSendMarker TruthValue,
iscsiCxnVersionActive Unsigned32
}
iscsiCxnIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An arbitrary integer used to uniquely identify a
particular connection of a particular session within
an iSCSI instance present on the local system. An
agent should attempt to not reuse index values unless
a reboot has occurred. iSCSI connections are destroyed
during a reboot; rows in this table are not persistent
across reboots."
::= { iscsiConnectionAttributesEntry 1 }
iscsiCxnCid OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The iSCSI Connection ID for this connection."
::= { iscsiConnectionAttributesEntry 2 }
iscsiCxnState OBJECT-TYPE
SYNTAX INTEGER {
login(1),
full(2),
logout(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current state of this connection, from an iSCSI negotiation
point of view. Here are the states:
login - The transport protocol connection has been established,
but a valid iSCSI login response with the final bit set
has not been sent or received.
full - A valid iSCSI login response with the final bit set
has been sent or received.
logout - A valid iSCSI logout command has been sent or
received, but the transport protocol connection has
not yet been closed."
::= { iscsiConnectionAttributesEntry 3 }
iscsiCxnAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The type of Internet Network Addresses contained in the
corresponding instances of iscsiCxnLocalAddr and
iscsiCxnRemoteAddr.
The value 'dns' is not allowed."
::= { iscsiConnectionAttributesEntry 4 }
iscsiCxnLocalAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The local Internet Network Address, of the type specified
by iscsiCxnAddrType, used by this connection."
::= { iscsiConnectionAttributesEntry 5 }
iscsiCxnProtocol OBJECT-TYPE
SYNTAX IscsiTransportProtocol
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The transport protocol over which this connection is
running."
::= { iscsiConnectionAttributesEntry 6 }
iscsiCxnLocalPort OBJECT-TYPE
SYNTAX InetPortNumber
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The local transport protocol port used by this connection.
This object cannot have the value zero, since it represents
an established connection."
::= { iscsiConnectionAttributesEntry 7 }
iscsiCxnRemoteAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The remote Internet Network Address, of the type specified
by iscsiCxnAddrType, used by this connection."
::= { iscsiConnectionAttributesEntry 8 }
iscsiCxnRemotePort OBJECT-TYPE
SYNTAX InetPortNumber
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The remote transport protocol port used by this connection.
This object cannot have the value zero, since it represents
an established connection."
::= { iscsiConnectionAttributesEntry 9 }
iscsiCxnMaxRecvDataSegLength OBJECT-TYPE
SYNTAX Unsigned32 (512..16777215)
UNITS "bytes"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum data payload size supported for command
or data PDUs able to be received on this connection."
REFERENCE
"RFC 3720, Section 12.12, MaxRecvDataSegmentLength"
::= { iscsiConnectionAttributesEntry 10 }
iscsiCxnMaxXmitDataSegLength OBJECT-TYPE
SYNTAX Unsigned32 (512..16777215)
UNITS "bytes"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum data payload size supported for command
or data PDUs to be sent on this connection."
REFERENCE
"RFC 3720, Section 12.12, MaxRecvDataSegmentLength"
::= { iscsiConnectionAttributesEntry 11 }
iscsiCxnHeaderIntegrity OBJECT-TYPE
SYNTAX IscsiDigestMethod
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object identifies the iSCSI header
digest scheme in use within this connection."
::= { iscsiConnectionAttributesEntry 12 }
iscsiCxnDataIntegrity OBJECT-TYPE
SYNTAX IscsiDigestMethod
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object identifies the iSCSI data
digest scheme in use within this connection."
::= { iscsiConnectionAttributesEntry 13 }
iscsiCxnRecvMarker OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates whether or not this connection
is receiving markers in its incoming data stream."
REFERENCE
"RFC 3720, Appendix A."
::= { iscsiConnectionAttributesEntry 14 }
iscsiCxnSendMarker OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates whether or not this connection
is inserting markers in its outgoing data stream."
REFERENCE
"RFC 3720, Appendix A."
::= { iscsiConnectionAttributesEntry 15 }
iscsiCxnVersionActive OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Active version number of the iSCSI specification negotiated
on this connection."
REFERENCE
"RFC 3720, Section 10.12, Login Request"
::= { iscsiConnectionAttributesEntry 16 }
--**********************************************************************
-- Notifications
iscsiTgtLoginFailure NOTIFICATION-TYPE
OBJECTS {
iscsiTgtLoginFailures,
iscsiTgtLastFailureType,
iscsiTgtLastIntrFailureName,
iscsiTgtLastIntrFailureAddrType,
iscsiTgtLastIntrFailureAddr
}
STATUS current
DESCRIPTION
"Sent when a login is failed by a target.
To avoid sending an excessive number of notifications due
to multiple errors counted, an SNMP agent implementing this
notification SHOULD NOT send more than 3 notifications of
this type in any 10-second time period."
::= { iscsiNotifications 1 }
iscsiIntrLoginFailure NOTIFICATION-TYPE
OBJECTS {
iscsiIntrLoginFailures,
iscsiIntrLastFailureType,
iscsiIntrLastTgtFailureName,
iscsiIntrLastTgtFailureAddrType,
iscsiIntrLastTgtFailureAddr
}
STATUS current
DESCRIPTION
"Sent when a login is failed by an initiator.
To avoid sending an excessive number of notifications due
to multiple errors counted, an SNMP agent implementing this
notification SHOULD NOT send more than 3 notifications of
this type in any 10-second time period."
::= { iscsiNotifications 2 }
iscsiInstSessionFailure NOTIFICATION-TYPE
OBJECTS {
iscsiInstSsnFailures,
iscsiInstLastSsnFailureType,
iscsiInstLastSsnRmtNodeName
}
STATUS current
DESCRIPTION
"Sent when an active session is failed by either the initiator
or the target.
To avoid sending an excessive number of notifications due
to multiple errors counted, an SNMP agent implementing this
notification SHOULD NOT send more than 3 notifications of
this type in any 10-second time period."
::= { iscsiNotifications 3 }
--**********************************************************************
-- Conformance Statements
iscsiCompliances OBJECT IDENTIFIER ::= { iscsiConformance 1 }
iscsiGroups OBJECT IDENTIFIER ::= { iscsiConformance 2 }
iscsiInstanceAttributesGroup OBJECT-GROUP
OBJECTS {
iscsiInstDescr,
iscsiInstVersionMin,
iscsiInstVersionMax,
iscsiInstVendorID,
iscsiInstVendorVersion,
iscsiInstPortalNumber,
iscsiInstNodeNumber,
iscsiInstSessionNumber,
iscsiInstSsnFailures,
iscsiInstLastSsnFailureType,
iscsiInstLastSsnRmtNodeName,
iscsiInstDiscontinuityTime
}
STATUS current
DESCRIPTION
"A collection of objects providing information about iSCSI
instances."
::= { iscsiGroups 1 }
iscsiInstanceSsnErrorStatsGroup OBJECT-GROUP
OBJECTS {
iscsiInstSsnDigestErrors,
iscsiInstSsnCxnTimeoutErrors,
iscsiInstSsnFormatErrors
}
STATUS current
DESCRIPTION
"A collection of objects providing information about
errors that have caused a session failure for an
iSCSI instance."
::= { iscsiGroups 2 }
iscsiPortalAttributesGroup OBJECT-GROUP
OBJECTS {
iscsiPortalRowStatus,
iscsiPortalStorageType,
iscsiPortalRoles,
iscsiPortalAddrType,
iscsiPortalAddr,
iscsiPortalProtocol,
iscsiPortalMaxRecvDataSegLength,
iscsiPortalPrimaryHdrDigest,
iscsiPortalPrimaryDataDigest,
iscsiPortalSecondaryHdrDigest,
iscsiPortalSecondaryDataDigest,
iscsiPortalRecvMarker
}
STATUS current
DESCRIPTION
"A collection of objects providing information about
the transport protocol endpoints of the local targets."
::= { iscsiGroups 3 }
iscsiTgtPortalAttributesGroup OBJECT-GROUP
OBJECTS {
iscsiTgtPortalPort,
iscsiTgtPortalTag
}
STATUS current
DESCRIPTION
"A collection of objects providing information about
the transport protocol endpoints of the local targets."
::= { iscsiGroups 4 }
iscsiIntrPortalAttributesGroup OBJECT-GROUP
OBJECTS {
iscsiIntrPortalTag
}
STATUS current
DESCRIPTION
"An object providing information about
the portal tags used by the local initiators."
::= { iscsiGroups 5 }
iscsiNodeAttributesGroup OBJECT-GROUP
OBJECTS {
iscsiNodeName,
iscsiNodeAlias,
iscsiNodeRoles,
iscsiNodeTransportType,
iscsiNodeInitialR2T,
iscsiNodeImmediateData,
iscsiNodeMaxOutstandingR2T,
iscsiNodeFirstBurstLength,
iscsiNodeMaxBurstLength,
iscsiNodeMaxConnections,
iscsiNodeDataSequenceInOrder,
iscsiNodeDataPDUInOrder,
iscsiNodeDefaultTime2Wait,
iscsiNodeDefaultTime2Retain,
iscsiNodeErrorRecoveryLevel,
iscsiNodeDiscontinuityTime,
iscsiNodeStorageType
}
STATUS current
DESCRIPTION
"A collection of objects providing information about all
local targets."
::= { iscsiGroups 6 }
iscsiTargetAttributesGroup OBJECT-GROUP
OBJECTS {
iscsiTgtLoginFailures,
iscsiTgtLastFailureTime,
iscsiTgtLastFailureType,
iscsiTgtLastIntrFailureName,
iscsiTgtLastIntrFailureAddrType,
iscsiTgtLastIntrFailureAddr
}
STATUS current
DESCRIPTION
"A collection of objects providing information about all
local targets."
::= { iscsiGroups 7 }
iscsiTargetLoginStatsGroup OBJECT-GROUP
OBJECTS {
iscsiTgtLoginAccepts,
iscsiTgtLoginOtherFails,
iscsiTgtLoginRedirects,
iscsiTgtLoginAuthorizeFails,
iscsiTgtLoginAuthenticateFails,
iscsiTgtLoginNegotiateFails
}
STATUS current
DESCRIPTION
"A collection of objects providing information about all
login attempts by remote initiators to local targets."
::= { iscsiGroups 8 }
iscsiTargetLogoutStatsGroup OBJECT-GROUP
OBJECTS {
iscsiTgtLogoutNormals,
iscsiTgtLogoutOthers
}
STATUS current
DESCRIPTION
"A collection of objects providing information about all
logout events between remote initiators and local targets."
::= { iscsiGroups 9 }
iscsiTargetAuthGroup OBJECT-GROUP
OBJECTS {
iscsiTgtAuthRowStatus,
iscsiTgtAuthStorageType,
iscsiTgtAuthIdentity
}
STATUS current
DESCRIPTION
"A collection of objects providing information about all
remote initiators that are authorized to connect to local
targets."
::= { iscsiGroups 10 }
iscsiInitiatorAttributesGroup OBJECT-GROUP
OBJECTS {
iscsiIntrLoginFailures,
iscsiIntrLastFailureTime,
iscsiIntrLastFailureType,
iscsiIntrLastTgtFailureName,
iscsiIntrLastTgtFailureAddrType,
iscsiIntrLastTgtFailureAddr
}
STATUS current
DESCRIPTION
"A collection of objects providing information about
all local initiators."
::= { iscsiGroups 11 }
iscsiInitiatorLoginStatsGroup OBJECT-GROUP
OBJECTS {
iscsiIntrLoginAcceptRsps,
iscsiIntrLoginOtherFailRsps,
iscsiIntrLoginRedirectRsps,
iscsiIntrLoginAuthFailRsps,
iscsiIntrLoginAuthenticateFails,
iscsiIntrLoginNegotiateFails
}
STATUS current
DESCRIPTION
"A collection of objects providing information about all
login attempts by local initiators to remote targets."
::= { iscsiGroups 12 }
iscsiInitiatorLogoutStatsGroup OBJECT-GROUP
OBJECTS {
iscsiIntrLogoutNormals,
iscsiIntrLogoutOthers
}
STATUS current
DESCRIPTION
"A collection of objects providing information about all
logout events between local initiators and remote targets."
::= { iscsiGroups 13 }
iscsiInitiatorAuthGroup OBJECT-GROUP
OBJECTS {
iscsiIntrAuthRowStatus,
iscsiIntrAuthStorageType,
iscsiIntrAuthIdentity
}
STATUS current
DESCRIPTION
"A collection of objects providing information about all
remote targets that are initiators of the local system
that they are authorized to access."
::= { iscsiGroups 14 }
iscsiSessionAttributesGroup OBJECT-GROUP
OBJECTS {
iscsiSsnDirection,
iscsiSsnInitiatorName,
iscsiSsnTargetName,
iscsiSsnTSIH,
iscsiSsnISID,
iscsiSsnInitiatorAlias,
iscsiSsnTargetAlias,
iscsiSsnInitialR2T,
iscsiSsnImmediateData,
iscsiSsnType,
iscsiSsnMaxOutstandingR2T,
iscsiSsnFirstBurstLength,
iscsiSsnMaxBurstLength,
iscsiSsnConnectionNumber,
iscsiSsnAuthIdentity,
iscsiSsnDataSequenceInOrder,
iscsiSsnDataPDUInOrder,
iscsiSsnErrorRecoveryLevel,
iscsiSsnDiscontinuityTime
}
STATUS current
DESCRIPTION
"A collection of objects providing information applicable to
all sessions."
::= { iscsiGroups 15 }
iscsiSessionPDUStatsGroup OBJECT-GROUP
OBJECTS {
iscsiSsnCmdPDUs,
iscsiSsnRspPDUs
}
STATUS current
DESCRIPTION
"A collection of objects providing information about PDU
traffic for each session."
::= { iscsiGroups 16 }
iscsiSessionOctetStatsGroup OBJECT-GROUP
OBJECTS {
iscsiSsnTxDataOctets,
iscsiSsnRxDataOctets
}
STATUS current
DESCRIPTION
"A collection of objects providing information about octet
traffic for each session using a Counter64 data type."
::= { iscsiGroups 17 }
iscsiSessionLCOctetStatsGroup OBJECT-GROUP
OBJECTS {
iscsiSsnLCTxDataOctets,
iscsiSsnLCRxDataOctets
}
STATUS current
DESCRIPTION
"A collection of objects providing information about octet
traffic for each session using a Counter32 data type."
::= { iscsiGroups 18 }
iscsiSessionCxnErrorStatsGroup OBJECT-GROUP
OBJECTS {
iscsiSsnCxnDigestErrors,
iscsiSsnCxnTimeoutErrors
}
STATUS current
DESCRIPTION
"A collection of objects providing information about connection
errors for all sessions."
::= { iscsiGroups 19 }
iscsiConnectionAttributesGroup OBJECT-GROUP
OBJECTS {
iscsiCxnCid,
iscsiCxnState,
iscsiCxnProtocol,
iscsiCxnAddrType,
iscsiCxnLocalAddr,
iscsiCxnLocalPort,
iscsiCxnRemoteAddr,
iscsiCxnRemotePort,
iscsiCxnMaxRecvDataSegLength,
iscsiCxnMaxXmitDataSegLength,
iscsiCxnHeaderIntegrity,
iscsiCxnDataIntegrity,
iscsiCxnRecvMarker,
iscsiCxnSendMarker,
iscsiCxnVersionActive
}
STATUS current
DESCRIPTION
"A collection of objects providing information about all
connections used by all sessions."
::= { iscsiGroups 20 }
iscsiTgtLgnNotificationsGroup NOTIFICATION-GROUP
NOTIFICATIONS {
iscsiTgtLoginFailure
}
STATUS current
DESCRIPTION
"A collection of notifications that indicate a login
failure from a remote initiator to a local target."
::= { iscsiGroups 21 }
iscsiIntrLgnNotificationsGroup NOTIFICATION-GROUP
NOTIFICATIONS {
iscsiIntrLoginFailure
}
STATUS current
DESCRIPTION
"A collection of notifications that indicate a login
failure from a local initiator to a remote target."
::= { iscsiGroups 22 }
iscsiSsnFlrNotificationsGroup NOTIFICATION-GROUP
NOTIFICATIONS {
iscsiInstSessionFailure
}
STATUS current
DESCRIPTION
"A collection of notifications that indicate session
failures occurring after login."
::= { iscsiGroups 23 }
--**********************************************************************
iscsiComplianceV1 MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"Initial version of compliance statement based on
initial version of this MIB module.
If an implementation can be both a target and an
initiator, all groups are mandatory."
MODULE -- this module
MANDATORY-GROUPS {
iscsiInstanceAttributesGroup,
iscsiInstanceSsnErrorStatsGroup,
iscsiPortalAttributesGroup,
iscsiNodeAttributesGroup,
iscsiSessionAttributesGroup,
iscsiSessionPDUStatsGroup,
iscsiSessionCxnErrorStatsGroup,
iscsiConnectionAttributesGroup,
iscsiSsnFlrNotificationsGroup
}
-- Conditionally mandatory groups depending on the ability
-- to support Counter64 data types and/or to provide counter
-- information to SNMPv1 applications.
GROUP iscsiSessionOctetStatsGroup
DESCRIPTION
"This group is mandatory for all iSCSI implementations
that can support Counter64 data types."
GROUP iscsiSessionLCOctetStatsGroup
DESCRIPTION
"This group is mandatory for all iSCSI implementations
that provide information to SNMPv1-only applications;
this includes agents that cannot support Counter64
data types."
-- Conditionally mandatory groups to be included with
-- the mandatory groups when the implementation has
-- iSCSI target facilities.
GROUP iscsiTgtPortalAttributesGroup
DESCRIPTION
"This group is mandatory for all iSCSI implementations
that have iSCSI target facilities."
OBJECT iscsiPortalMaxRecvDataSegLength
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT iscsiNodeStorageType
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required; an implementation may
choose to allow this object to be set to 'volatile'
or 'nonVolatile'."
GROUP iscsiTargetAttributesGroup
DESCRIPTION
"This group is mandatory for all iSCSI implementations
that have iSCSI target facilities."
GROUP iscsiTargetLoginStatsGroup
DESCRIPTION
"This group is mandatory for all iSCSI implementations
that have iSCSI target facilities."
GROUP iscsiTargetLogoutStatsGroup
DESCRIPTION
"This group is mandatory for all iSCSI implementations
that have iSCSI target facilities."
GROUP iscsiTgtLgnNotificationsGroup
DESCRIPTION
"This group is mandatory for all iSCSI implementations
that have iSCSI target facilities."
GROUP iscsiTargetAuthGroup
DESCRIPTION
"This group is mandatory for all iSCSI implementations
that have iSCSI target facilities."
-- Conditionally mandatory groups to be included with
-- the mandatory groups when the implementation has
-- iSCSI initiator facilities.
GROUP iscsiIntrPortalAttributesGroup
DESCRIPTION
"This group is mandatory for all iSCSI implementations
that have iSCSI initiator facilities."
GROUP iscsiInitiatorAttributesGroup
DESCRIPTION
"This group is mandatory for all iSCSI implementations
that have iSCSI initiator facilities."
GROUP iscsiInitiatorLoginStatsGroup
DESCRIPTION
"This group is mandatory for all iSCSI implementations
that have iSCSI initiator facilities."
GROUP iscsiInitiatorLogoutStatsGroup
DESCRIPTION
"This group is mandatory for all iSCSI implementations
that have iSCSI initiator facilities."
GROUP iscsiIntrLgnNotificationsGroup
DESCRIPTION
"This group is mandatory for all iSCSI implementations
that have iSCSI initiator facilities."
GROUP iscsiInitiatorAuthGroup
DESCRIPTION
"This group is mandatory for all iSCSI implementations
that have iSCSI initiator facilities."
OBJECT iscsiNodeErrorRecoveryLevel
SYNTAX Unsigned32 (0..2)
DESCRIPTION
"Only values 0-2 are defined at present."
::= { iscsiCompliances 1 }
END