VDSL-LINE-EXT-MCM-MIB DEFINITIONS ::= BEGIN

IMPORTS

MODULE-IDENTITY,

OBJECT-TYPE,

transmission,

Unsigned32                      FROM SNMPv2-SMI         -- [RFC2578]

RowStatus                       FROM SNMPv2-TC          -- [RFC2579]

MODULE-COMPLIANCE,

OBJECT-GROUP                    FROM SNMPv2-CONF        -- [RFC2580]

vdslLineConfProfileName         FROM VDSL-LINE-MIB;     -- [RFC3728]

vdslExtMCMMIB MODULE-IDENTITY

   LAST-UPDATED "200504280000Z" --    April 28, 2005

   ORGANIZATION "ADSLMIB Working Group"

   CONTACT-INFO "WG-email:  adslmib@ietf.org

         Info:      https://www1.ietf.org/mailman/listinfo/adslmib

         Chair:     Mike Sneed

                    Sand Channel Systems

         Postal:    P.O. Box 37324

                    Raleigh NC 27627-732

         Email:     sneedmike@hotmail.com

         Phone:     +1 206 600 7022

         Co-Chair/Co-editor:

                    Bob Ray

                    PESA Switching Systems, Inc.

         Postal:    330-A Wynn Drive

                    Huntsville, AL 35805

                    USA

         Email:     rray@pesa.com

         Phone:     +1 256 726 9200 ext.  142

         Co-editor: Menachem Dodge

                    ECI Telecom Ltd.

         Postal:    30 hasivim St.

                    Petach Tikva 49517,

                    Israel.

         Email:     mbdodge@ieee.org

         Phone:     +972 3 926 8421

        "

DESCRIPTION

    "The VDSL-LINE-MIB found in RFC 3728 defines objects for

    the management of a pair of VDSL transceivers at each end of

    the VDSL line.  The VDSL-LINE-MIB configures and monitors the

    line code independent parameters (TC layer) of the VDSL line.

    This MIB module is an optional extension of the VDSL-LINE-MIB

    and defines objects for configuration and monitoring of the

    line code specific (LCS) elements (PMD layer) for VDSL lines

    using MCM coding.  The objects in this extension MIB MUST NOT

    be used for VDSL lines using Single Carrier Modulation (SCM)

    line coding.  If an object in this extension MIB is referenced

    by a line which does not use MCM, it has no effect on the

    operation of that line.

    Naming Conventions:

        Vtuc -- (VTUC) transceiver at near (Central) end of line

        Vtur -- (VTUR) transceiver at Remote end of line

        Vtu  -- One of either Vtuc or Vtur

        Curr -- Current

        LCS  -- Line Code Specific

        Max  -- Maximum

        PSD  -- Power Spectral Density

        Rx   -- Receive

        Tx   -- Transmit

    Copyright (C) The Internet Society (2005).  This version

    of this MIB module is part of RFC 4070: see the RFC

    itself for full legal notices."

        REVISION "200504280000Z" --    April 28, 2005

        DESCRIPTION "Initial version, published as RFC 4070."

    ::= { transmission 229 }

vdslLineExtMCMMib OBJECT IDENTIFIER ::= { vdslExtMCMMIB 1 }

vdslLineExtMCMMibObjects OBJECT IDENTIFIER ::= {vdslLineExtMCMMib 1}

--

-- Multiple carrier modulation (MCM) configuration profile tables

--

vdslLineMCMConfProfileTable OBJECT-TYPE

    SYNTAX       SEQUENCE OF VdslLineMCMConfProfileEntry

    MAX-ACCESS   not-accessible

    STATUS       current

    DESCRIPTION

        "This table contains additional information on multiple

        carrier VDSL lines.  One entry in this table reflects a

        profile defined by a manager which can be used to

        configure the VDSL line.

        If an entry in this table is referenced by a line which

        does not use MCM, it has no effect on the operation of that

        line.

        All read-create-objects defined in this table SHOULD be

        stored persistently."

    ::= { vdslLineExtMCMMibObjects  1 }

vdslLineMCMConfProfileEntry OBJECT-TYPE

    SYNTAX       VdslLineMCMConfProfileEntry

    MAX-ACCESS   not-accessible

    STATUS       current

    DESCRIPTION

        "Each entry consists of a list of parameters that

        represents the configuration of a multiple carrier

        modulation VDSL modem."

    INDEX { vdslLineConfProfileName }

    ::= { vdslLineMCMConfProfileTable 1 }

VdslLineMCMConfProfileEntry ::=

    SEQUENCE

        {

        vdslLineMCMConfProfileTxWindowLength       Unsigned32,

        vdslLineMCMConfProfileRowStatus            RowStatus

        }

vdslLineMCMConfProfileTxWindowLength OBJECT-TYPE

    SYNTAX       Unsigned32 (1..255)

    UNITS        "samples"

    MAX-ACCESS   read-create

    STATUS       current

    DESCRIPTION

        "Specifies the length of the transmit window, counted

        in samples at the sampling rate corresponding to the

        negotiated value of N."

    REFERENCE    "T1E1.4/2000-013R4"    -- Part 3, MCM

    ::= { vdslLineMCMConfProfileEntry 1 }

vdslLineMCMConfProfileRowStatus OBJECT-TYPE

    SYNTAX       RowStatus

    MAX-ACCESS   read-create

    STATUS       current

    DESCRIPTION

        "This object is used to create a new row or modify or

        delete an existing row in this table.

        A profile is activated by setting this object to `active'.

        When `active' is set, the system will validate the profile.

        None of the columns in this row may be modified while the

        row is in the 'active' state.

        Before a profile can be deleted or taken out of

        service, (by setting this object to `destroy' or

        `notInService') it must first be unreferenced

        from all associated lines."

    ::= { vdslLineMCMConfProfileEntry 2 }

vdslLineMCMConfProfileTxBandTable OBJECT-TYPE

    SYNTAX       SEQUENCE OF VdslLineMCMConfProfileTxBandEntry

    MAX-ACCESS   not-accessible

    STATUS       current

    DESCRIPTION

        "This table contains transmit band descriptor configuration

        information for a VDSL line.  Each entry in this table

        reflects the configuration for one of possibly many bands

        with a multiple carrier modulation (MCM) VDSL line.

        These entries are defined by a manager and can be used to

        configure the VDSL line.

        If an entry in this table is referenced by a line which

        does not use MCM, it has no effect on the operation of that

        line.

        All read-create-objects defined in this table SHOULD be

        stored persistently."

    ::= { vdslLineExtMCMMibObjects  2 }

vdslLineMCMConfProfileTxBandEntry OBJECT-TYPE

    SYNTAX       VdslLineMCMConfProfileTxBandEntry

    MAX-ACCESS   not-accessible

    STATUS       current

    DESCRIPTION

        "Each entry consists of a transmit band descriptor, which

        is defined by a start and a stop tone index."

    INDEX { vdslLineConfProfileName,

            vdslLineMCMConfProfileTxBandNumber }

    ::= { vdslLineMCMConfProfileTxBandTable 1 }

VdslLineMCMConfProfileTxBandEntry ::=

    SEQUENCE

        {

        vdslLineMCMConfProfileTxBandNumber           Unsigned32,

        vdslLineMCMConfProfileTxBandStart            Unsigned32,

        vdslLineMCMConfProfileTxBandStop             Unsigned32,

        vdslLineMCMConfProfileTxBandRowStatus        RowStatus

        }

vdslLineMCMConfProfileTxBandNumber OBJECT-TYPE

    SYNTAX       Unsigned32 (1..4096)

    MAX-ACCESS   not-accessible

    STATUS       current

    DESCRIPTION

        "The index for this band descriptor entry."

    ::= { vdslLineMCMConfProfileTxBandEntry 1 }

vdslLineMCMConfProfileTxBandStart OBJECT-TYPE

    SYNTAX       Unsigned32 (1..4096)

    MAX-ACCESS   read-create

    STATUS       current

    DESCRIPTION

        "Start tone index for this band."

    REFERENCE    "T1E1.4/2000-013R4"    -- Part 3, MCM

    ::= { vdslLineMCMConfProfileTxBandEntry 2 }

vdslLineMCMConfProfileTxBandStop OBJECT-TYPE

    SYNTAX       Unsigned32 (1..4096)

    MAX-ACCESS   read-create

    STATUS       current

    DESCRIPTION

        "Stop tone index for this band."

    REFERENCE    "T1E1.4/2000-013R4"    -- Part 3, MCM

    ::= { vdslLineMCMConfProfileTxBandEntry 3 }

vdslLineMCMConfProfileTxBandRowStatus OBJECT-TYPE

    SYNTAX       RowStatus

    MAX-ACCESS   read-create

    STATUS       current

    DESCRIPTION

        "This object is used to create a new row or modify or

        delete an existing row in this table.

        A profile is activated by setting this object to `active'.

        When `active' is set, the system will validate the profile.

        Each entry must be internally consistent, the Stop Tone must

        be greater than the Start Tone.  Each entry must also be

        externally consistent, all entries indexed by a specific

        profile must not overlap.  Validation of the profile will

        check both internal and external consistency.

        None of the columns in this row may be modified while the

        row is in the 'active' state.

        Before a profile can be deleted or taken out of

        service, (by setting this object to `destroy' or

        `notInService') it must be first unreferenced

        from all associated lines."

    ::= { vdslLineMCMConfProfileTxBandEntry 4 }

vdslLineMCMConfProfileRxBandTable OBJECT-TYPE

    SYNTAX       SEQUENCE OF VdslLineMCMConfProfileRxBandEntry

    MAX-ACCESS   not-accessible

    STATUS       current

    DESCRIPTION

        "This table contains receive band descriptor configuration

        information for a VDSL line.  Each entry in this table

        reflects the configuration for one of possibly many bands

        with a multiple carrier modulation (MCM) VDSL line.

        These entries are defined by a manager and can be used to

        configure the VDSL line.

        If an entry in this table is referenced by a line which

        does not use MCM, it has no effect on the operation of that

        line.

        All read-create-objects defined in this table SHOULD be

        stored persistently."

    ::= { vdslLineExtMCMMibObjects 3 }

vdslLineMCMConfProfileRxBandEntry OBJECT-TYPE

    SYNTAX       VdslLineMCMConfProfileRxBandEntry

    MAX-ACCESS   not-accessible

    STATUS       current

    DESCRIPTION

        "Each entry consists of a transmit band descriptor, which

        is defined by a start and a stop tone index."

    INDEX { vdslLineConfProfileName,

            vdslLineMCMConfProfileRxBandNumber }

    ::= { vdslLineMCMConfProfileRxBandTable 1 }

VdslLineMCMConfProfileRxBandEntry ::=

    SEQUENCE

        {

        vdslLineMCMConfProfileRxBandNumber           Unsigned32,

        vdslLineMCMConfProfileRxBandStart            Unsigned32,

        vdslLineMCMConfProfileRxBandStop             Unsigned32,

        vdslLineMCMConfProfileRxBandRowStatus        RowStatus

        }

vdslLineMCMConfProfileRxBandNumber OBJECT-TYPE

    SYNTAX       Unsigned32 (1..4096)

    MAX-ACCESS   not-accessible

    STATUS       current

    DESCRIPTION

        "The index for this band descriptor entry."

    ::= { vdslLineMCMConfProfileRxBandEntry 1 }

vdslLineMCMConfProfileRxBandStart OBJECT-TYPE

    SYNTAX       Unsigned32 (1..4096)

    MAX-ACCESS   read-create

    STATUS       current

    DESCRIPTION

        "Start tone index for this band."

    REFERENCE    "T1E1.4/2000-013R4"    -- Part 3, MCM

    ::= { vdslLineMCMConfProfileRxBandEntry 2 }

vdslLineMCMConfProfileRxBandStop OBJECT-TYPE

    SYNTAX       Unsigned32 (1..4096)

    MAX-ACCESS   read-create

    STATUS       current

    DESCRIPTION

        "Stop tone index for this band."

    REFERENCE    "T1E1.4/2000-013R4"    -- Part 3, MCM

    ::= { vdslLineMCMConfProfileRxBandEntry 3 }

vdslLineMCMConfProfileRxBandRowStatus OBJECT-TYPE

    SYNTAX       RowStatus

    MAX-ACCESS   read-create

    STATUS       current

    DESCRIPTION

        "This object is used to create a new row or modify or

        delete an existing row in this table.

        A profile is activated by setting this object to `active'.

        When `active' is set, the system will validate the profile.

        Each entry must be internally consistent, the Stop Tone must

        be greater than the Start Tone.  Each entry must also be

        externally consistent, all entries indexed by a specific

        profile must not overlap.  Validation of the profile will

        check both internal and external consistency.

        None of the columns in this row may be modified while the

        row is in the 'active' state.

        Before a profile can be deleted or taken out of

        service, (by setting this object to `destroy' or

        `notInService') it must be first unreferenced

        from all associated lines."

    ::= { vdslLineMCMConfProfileRxBandEntry 4 }

vdslLineMCMConfProfileTxPSDTable OBJECT-TYPE

    SYNTAX       SEQUENCE OF VdslLineMCMConfProfileTxPSDEntry

    MAX-ACCESS   not-accessible

    STATUS       current

    DESCRIPTION

        "This table contains transmit PSD mask descriptor

        configuration information for a VDSL line.  Each entry in

        this table reflects the configuration for one tone within

        a multiple carrier modulation (MCM) VDSL line.  These

        entries are defined by a manager and can be used to

        configure the VDSL line.

        If an entry in this table is referenced by a line which

        does not use MCM, it has no effect on the operation of that

        line.

        All read-create-objects defined in this table SHOULD be

        stored persistently."

    ::= { vdslLineExtMCMMibObjects 4 }

vdslLineMCMConfProfileTxPSDEntry OBJECT-TYPE

    SYNTAX       VdslLineMCMConfProfileTxPSDEntry

    MAX-ACCESS   not-accessible

    STATUS       current

    DESCRIPTION

        "Each entry consists of a transmit PSD mask descriptor,

        which defines the power spectral density (PSD) for a tone."

    INDEX { vdslLineConfProfileName,

            vdslLineMCMConfProfileTxPSDNumber }

    ::= { vdslLineMCMConfProfileTxPSDTable 1 }

VdslLineMCMConfProfileTxPSDEntry ::=

    SEQUENCE

        {

        vdslLineMCMConfProfileTxPSDNumber            Unsigned32,

        vdslLineMCMConfProfileTxPSDTone              Unsigned32,

        vdslLineMCMConfProfileTxPSDPSD               Unsigned32,

        vdslLineMCMConfProfileTxPSDRowStatus         RowStatus

        }

vdslLineMCMConfProfileTxPSDNumber OBJECT-TYPE

    SYNTAX       Unsigned32 (1..4096)

    MAX-ACCESS   not-accessible

    STATUS       current

    DESCRIPTION

        "The index for this mask descriptor entry."

    ::= { vdslLineMCMConfProfileTxPSDEntry 1 }

vdslLineMCMConfProfileTxPSDTone OBJECT-TYPE

    SYNTAX       Unsigned32 (1..4096)

    MAX-ACCESS   read-create

    STATUS       current

    DESCRIPTION

        "The tone index for which the PSD is being specified."

    REFERENCE    "T1E1.4/2000-013R4"    -- Part 3, MCM

    ::= { vdslLineMCMConfProfileTxPSDEntry 2 }

vdslLineMCMConfProfileTxPSDPSD OBJECT-TYPE

    SYNTAX       Unsigned32

    UNITS        "0.5dBm/Hz"

    MAX-ACCESS   read-create

    STATUS       current

    DESCRIPTION

        "Power Spectral Density level in steps of 0.5dBm/Hz with

        an offset of -140dBm/Hz."

    REFERENCE    "T1E1.4/2000-013R4"    -- Part 3, MCM

    ::= { vdslLineMCMConfProfileTxPSDEntry 3 }

    vdslLineMCMConfProfileTxPSDRowStatus OBJECT-TYPE

        SYNTAX       RowStatus

        MAX-ACCESS   read-create

        STATUS       current

        DESCRIPTION

            "This object is used to create a new row or modify or

        delete an existing row in this table.

        A profile is activated by setting this object to `active'.

        When `active' is set, the system will validate the profile.

        None of the columns in this row may be modified while the

        row is in the 'active' state.

        Before a profile can be deleted or taken out of

        service, (by setting this object to `destroy' or

        `notInService') it must be first unreferenced

        from all associated lines."

    ::= { vdslLineMCMConfProfileTxPSDEntry 4 }

vdslLineMCMConfProfileMaxTxPSDTable OBJECT-TYPE

    SYNTAX       SEQUENCE OF VdslLineMCMConfProfileMaxTxPSDEntry

    MAX-ACCESS   not-accessible

    STATUS       current

    DESCRIPTION

        "This table contains transmit maximum PSD mask descriptor

        configuration information for a VDSL line.  Each entry in

        this table reflects the configuration for one tone within

        a multiple carrier modulation (MCM) VDSL modem.  These

        entries are defined by a manager and can be used to

        configure the VDSL line.

        If an entry in this table is referenced by a line which

        does not use MCM, it has no effect on the operation of that

        line.

        All read-create-objects defined in this table SHOULD be

        stored persistently."

    ::= { vdslLineExtMCMMibObjects 5 }

vdslLineMCMConfProfileMaxTxPSDEntry OBJECT-TYPE

    SYNTAX       VdslLineMCMConfProfileMaxTxPSDEntry

    MAX-ACCESS   not-accessible

    STATUS       current

    DESCRIPTION

        "Each entry consists of a transmit PSD mask descriptor,

        which defines the maximum power spectral density (PSD)

        for a tone."

    INDEX { vdslLineConfProfileName,

            vdslLineMCMConfProfileMaxTxPSDNumber }

    ::= { vdslLineMCMConfProfileMaxTxPSDTable 1 }

VdslLineMCMConfProfileMaxTxPSDEntry ::=

    SEQUENCE

        {

        vdslLineMCMConfProfileMaxTxPSDNumber            Unsigned32,

        vdslLineMCMConfProfileMaxTxPSDTone              Unsigned32,

        vdslLineMCMConfProfileMaxTxPSDPSD               Unsigned32,

        vdslLineMCMConfProfileMaxTxPSDRowStatus         RowStatus

        }

vdslLineMCMConfProfileMaxTxPSDNumber OBJECT-TYPE

    SYNTAX       Unsigned32 (1..4096)

    MAX-ACCESS   not-accessible

    STATUS       current

    DESCRIPTION

        "The index for this band descriptor entry."

    ::= { vdslLineMCMConfProfileMaxTxPSDEntry 1 }

vdslLineMCMConfProfileMaxTxPSDTone OBJECT-TYPE

    SYNTAX       Unsigned32 (1..4096)

    MAX-ACCESS   read-create

    STATUS       current

    DESCRIPTION

        "The tone index for which the PSD is being specified.

         There must not be multiple rows defined, for a particular

         profile, with the same value for this field."

    REFERENCE    "T1E1.4/2000-013R4"    -- Part 3, MCM

    ::= { vdslLineMCMConfProfileMaxTxPSDEntry 2 }

vdslLineMCMConfProfileMaxTxPSDPSD OBJECT-TYPE

    SYNTAX       Unsigned32

    UNITS        "0.5dBm/Hz"

    MAX-ACCESS   read-create

    STATUS       current

    DESCRIPTION

        "Power Spectral Density level in steps of 0.5dBm/Hz with

        an offset of -140dBm/Hz."

    REFERENCE    "T1E1.4/2000-013R4"    -- Part 3, MCM

    ::= { vdslLineMCMConfProfileMaxTxPSDEntry 3 }

vdslLineMCMConfProfileMaxTxPSDRowStatus OBJECT-TYPE

    SYNTAX       RowStatus

    MAX-ACCESS   read-create

    STATUS       current

    DESCRIPTION

        "This object is used to create a new row or modify or

        delete an existing row in this table.

        A profile is activated by setting this object to `active'.

        When `active' is set, the system will validate the profile.

        There must be only one entry in this table for each tone

        associated with a specific profile.  This will be checked

        during the validation process.

        None of the columns in this row may be modified while the

        row is in the 'active' state.

        Before a profile can be deleted or taken out of

        service, (by setting this object to `destroy' or

        `notInService') it must be first unreferenced

        from all associated lines."

    ::= { vdslLineMCMConfProfileMaxTxPSDEntry 4 }

vdslLineMCMConfProfileMaxRxPSDTable OBJECT-TYPE

    SYNTAX       SEQUENCE OF VdslLineMCMConfProfileMaxRxPSDEntry

    MAX-ACCESS   not-accessible

    STATUS       current

    DESCRIPTION

        "This table contains maximum receive PSD mask descriptor

        configuration information for a VDSL line.  Each entry in

        this table reflects the configuration for one tone within

        a multiple carrier modulation (MCM) VDSL modem.  These

        entries are defined by a manager and can be used to

        configure the VDSL line.

        If an entry in this table is referenced by a line which

        does not use MCM, it has no effect on the operation of that

        line.

        All read-create-objects defined in this table SHOULD be

        stored persistently."

    ::= { vdslLineExtMCMMibObjects 6 }

vdslLineMCMConfProfileMaxRxPSDEntry OBJECT-TYPE

    SYNTAX       VdslLineMCMConfProfileMaxRxPSDEntry

    MAX-ACCESS   not-accessible

    STATUS       current

    DESCRIPTION

        "Each entry consists of a transmit PSD mask descriptor,

        which defines the power spectral density (PSD) for a

        tone."

    INDEX { vdslLineConfProfileName,

            vdslLineMCMConfProfileMaxRxPSDNumber }

    ::= { vdslLineMCMConfProfileMaxRxPSDTable 1 }

VdslLineMCMConfProfileMaxRxPSDEntry ::=

    SEQUENCE

        {

        vdslLineMCMConfProfileMaxRxPSDNumber            Unsigned32,

        vdslLineMCMConfProfileMaxRxPSDTone              Unsigned32,

        vdslLineMCMConfProfileMaxRxPSDPSD               Unsigned32,

        vdslLineMCMConfProfileMaxRxPSDRowStatus         RowStatus

        }

vdslLineMCMConfProfileMaxRxPSDNumber OBJECT-TYPE

    SYNTAX       Unsigned32 (1..4096)

    MAX-ACCESS   not-accessible

    STATUS       current

    DESCRIPTION

        "The index for this band descriptor entry."

    ::= { vdslLineMCMConfProfileMaxRxPSDEntry 1 }

vdslLineMCMConfProfileMaxRxPSDTone OBJECT-TYPE

    SYNTAX       Unsigned32 (1..4096)

    MAX-ACCESS   read-create

    STATUS       current

    DESCRIPTION

        "The tone index for which the PSD is being specified.

         There must not be multiple rows defined, for a particular

         profile, with the same value for this field."

    REFERENCE    "T1E1.4/2000-013R4"    -- Part 3, MCM

    ::= { vdslLineMCMConfProfileMaxRxPSDEntry 2 }

vdslLineMCMConfProfileMaxRxPSDPSD OBJECT-TYPE

    SYNTAX       Unsigned32

    UNITS        "0.5dBm/Hz"

    MAX-ACCESS   read-create

    STATUS       current

    DESCRIPTION

        "Power Spectral Density level in steps of 0.5dBm/Hz with

        an offset of -140dBm/Hz."

    REFERENCE    "T1E1.4/2000-013R4"    -- Part 3, MCM

    ::= { vdslLineMCMConfProfileMaxRxPSDEntry 3 }

vdslLineMCMConfProfileMaxRxPSDRowStatus OBJECT-TYPE

    SYNTAX       RowStatus

    MAX-ACCESS   read-create

    STATUS       current

    DESCRIPTION

        "This object is used to create a new row or modify or

        delete an existing row in this table.

        A profile is activated by setting this object to `active'.

        When `active' is set, the system will validate the profile.

        There must be only one entry in this table for each tone

        associated with a specific profile.  This will be checked

        during the validation process.

        None of the columns in this row may be modified while the

        row is in the 'active' state.

        Before a profile can be deleted or taken out of

        service, (by setting this object to `destroy' or

        `notInService') it must be first unreferenced

        from all associated lines."

    ::= { vdslLineMCMConfProfileMaxRxPSDEntry 4 }

-- conformance information

vdslLineExtMCMConformance OBJECT IDENTIFIER ::=

                 { vdslLineExtMCMMib 2 }

vdslLineExtMCMGroups OBJECT IDENTIFIER ::=

                 { vdslLineExtMCMConformance 1 }

vdslLineExtMCMCompliances OBJECT IDENTIFIER ::=

                 { vdslLineExtMCMConformance 2 }

vdslLineExtMCMMibCompliance MODULE-COMPLIANCE

    STATUS  current

    DESCRIPTION

        "The compliance statement for SNMP entities which

        manage VDSL interfaces."

    MODULE  -- this module

    MANDATORY-GROUPS

    {

        vdslLineExtMCMGroup

    }

    ::= { vdslLineExtMCMCompliances 1 }

-- units of conformance

    vdslLineExtMCMGroup OBJECT-GROUP

        OBJECTS

            {

            vdslLineMCMConfProfileTxWindowLength,

            vdslLineMCMConfProfileRowStatus,

            vdslLineMCMConfProfileTxBandStart,

            vdslLineMCMConfProfileTxBandStop,

            vdslLineMCMConfProfileTxBandRowStatus,

            vdslLineMCMConfProfileRxBandStart,

            vdslLineMCMConfProfileRxBandStop,

            vdslLineMCMConfProfileRxBandRowStatus,

            vdslLineMCMConfProfileTxPSDTone,

            vdslLineMCMConfProfileTxPSDPSD,

            vdslLineMCMConfProfileTxPSDRowStatus,

            vdslLineMCMConfProfileMaxTxPSDTone,

            vdslLineMCMConfProfileMaxTxPSDPSD,

            vdslLineMCMConfProfileMaxTxPSDRowStatus,

            vdslLineMCMConfProfileMaxRxPSDTone,

            vdslLineMCMConfProfileMaxRxPSDPSD,

            vdslLineMCMConfProfileMaxRxPSDRowStatus

            }

         STATUS     current

         DESCRIPTION

             "A collection of objects providing configuration

             information for a VDSL line based upon multiple

             carrier modulation modem."

     ::= { vdslLineExtMCMGroups 1 }

END