MPLS-LDP-ATM-STD-MIB DEFINITIONS ::= BEGIN

IMPORTS

    OBJECT-TYPE, MODULE-IDENTITY,

    Unsigned32

        FROM SNMPv2-SMI                                 --  [RFC2578]

    MODULE-COMPLIANCE, OBJECT-GROUP

        FROM SNMPv2-CONF                                --  [RFC2580]

    RowStatus,

    StorageType

        FROM SNMPv2-TC                                  --  [RFC2579]

    InterfaceIndexOrZero

        FROM IF-MIB                                     --  [RFC2020]

    AtmVpIdentifier

        FROM ATM-TC-MIB                                 --  [RFC2514]

    mplsStdMIB,

    MplsAtmVcIdentifier

        FROM MPLS-TC-STD-MIB                            --  [RFC3811]

    mplsLdpEntityLdpId,

    mplsLdpEntityIndex,

    mplsLdpPeerLdpId

        FROM MPLS-LDP-STD-MIB                           --  [RFC3813]

    ;

mplsLdpAtmStdMIB MODULE-IDENTITY

    LAST-UPDATED "200406030000Z"  -- June 3, 2004

    ORGANIZATION "Multiprotocol Label Switching (mpls)

                  Working Group"

    CONTACT-INFO

        "Joan Cucchiara (jcucchiara@mindspring.com)

         Marconi Communications, Inc.

         Hans Sjostrand (hans@ipunplugged.com)

         ipUnplugged

         James V. Luciani (james_luciani@mindspring.com)

         Marconi Communications, Inc.

         Working Group Chairs:

         George Swallow,   email: swallow@cisco.com

         Loa Andersson,    email: loa@pi.se

         MPLS Working Group, email: mpls@uu.net

    "

    DESCRIPTION

        "Copyright (C) The Internet Society (2004). The

        initial version of this MIB module was published

        in RFC 3815. For full legal notices see the RFC

        itself or see:

        http://www.ietf.org/copyrights/ianamib.html

        This MIB contains managed object definitions for

        configuring and monitoring the Multiprotocol Label

        Switching (MPLS), Label Distribution Protocol (LDP),

        utilizing Asynchronous Transfer Mode (ATM) as the Layer 2

        media."

    REVISION "200406030000Z"  -- June 3, 2004

    DESCRIPTION

        "Initial version published as part of RFC 3815."

    ::= { mplsStdMIB 5 }

--****************************************************************

mplsLdpAtmObjects       OBJECT IDENTIFIER

                            ::= { mplsLdpAtmStdMIB 1 }

mplsLdpAtmConformance   OBJECT IDENTIFIER

                            ::= { mplsLdpAtmStdMIB 2 }

--****************************************************************

-- MPLS LDP ATM Objects

--****************************************************************

--

-- Ldp Entity Objects for ATM

--

mplsLdpEntityAtmObjects  OBJECT IDENTIFIER ::=

                              { mplsLdpAtmObjects 1 }

mplsLdpEntityAtmTable  OBJECT-TYPE

    SYNTAX      SEQUENCE OF MplsLdpEntityAtmEntry

    MAX-ACCESS  not-accessible

    STATUS      current

    DESCRIPTION

        "This table contains ATM specific information

        which could be used in the

        'Optional Parameters' and other ATM specific

        information.

        This table 'sparse augments' the mplsLdpEntityTable

        when ATM is the Layer 2 medium."

    ::= { mplsLdpEntityAtmObjects 1 }

mplsLdpEntityAtmEntry OBJECT-TYPE

    SYNTAX      MplsLdpEntityAtmEntry

    MAX-ACCESS  not-accessible

    STATUS      current

    DESCRIPTION

        "An entry in this table represents the ATM parameters

        and ATM information for this LDP entity."

    INDEX       {  mplsLdpEntityLdpId,

                   mplsLdpEntityIndex

                }

    ::= { mplsLdpEntityAtmTable 1 }

MplsLdpEntityAtmEntry ::= SEQUENCE {

    mplsLdpEntityAtmIfIndexOrZero        InterfaceIndexOrZero,

    mplsLdpEntityAtmMergeCap             INTEGER,

    mplsLdpEntityAtmLRComponents         Unsigned32,

    mplsLdpEntityAtmVcDirectionality     INTEGER,

    mplsLdpEntityAtmLsrConnectivity      INTEGER,

    mplsLdpEntityAtmDefaultControlVpi    AtmVpIdentifier,

    mplsLdpEntityAtmDefaultControlVci    MplsAtmVcIdentifier,

    mplsLdpEntityAtmUnlabTrafVpi         AtmVpIdentifier,

    mplsLdpEntityAtmUnlabTrafVci         MplsAtmVcIdentifier,

    mplsLdpEntityAtmStorageType          StorageType,

    mplsLdpEntityAtmRowStatus            RowStatus

}

mplsLdpEntityAtmIfIndexOrZero  OBJECT-TYPE

    SYNTAX      InterfaceIndexOrZero

    MAX-ACCESS  read-create

    STATUS      current

    DESCRIPTION

       "This value represents either the InterfaceIndex

       or 0 (zero).  The value of zero means that the

       InterfaceIndex is not known.

       However, if the InterfaceIndex is known, then it must

       be represented by this value.

       If an InterfaceIndex becomes known, then the

       network management entity (e.g., SNMP agent) responsible

       for this object MUST change the value from 0 (zero) to the

       value of the InterfaceIndex.  If an ATM Label is

       being used in forwarding data, then the value of this

       object MUST be the InterfaceIndex."

    ::= { mplsLdpEntityAtmEntry 1 }

mplsLdpEntityAtmMergeCap OBJECT-TYPE

    SYNTAX      INTEGER {

                    notSupported(0),

                    vpMerge(1),

                    vcMerge(2),

                    vpAndVcMerge(3)

                }

    MAX-ACCESS  read-create

    STATUS      current

    DESCRIPTION

        "Denotes the Merge Capability of this Entity.

        This is the EXACT value for the ATM Session

        Parameter, field M (for ATM Merge Capabilities).

        The ATM Session Parameter is an optional

        parameter in the Initialization Message.

        The description from rfc3036.txt is:

        'M, ATM Merge Capabilities

           Specifies the merge capabilities of an ATM switch.  The

           following values are supported in this version of the

           specification:

                  Value          Meaning

                    0            Merge not supported

                    1            VP Merge supported

                    2            VC Merge supported

                    3            VP & VC Merge supported

           If the merge capabilities of the LSRs differ, then:

           -  Non-merge and VC-merge LSRs may freely interoperate.

           -  The interoperability of VP-merge-capable switches

              with non-VP-merge-capable switches is a subject

              for future study.  When the LSRs differ on the

              use of VP-merge, the session is established,

              but VP merge is not used.'

           Please refer to the following reference for a

           complete description of this feature."

     REFERENCE

        "RFC3036, LDP Specification, Section 3.5.3

        Initialization Message."

    ::= { mplsLdpEntityAtmEntry 2 }

mplsLdpEntityAtmLRComponents OBJECT-TYPE

    SYNTAX      Unsigned32 (1..65535)

    MAX-ACCESS  read-only

    STATUS      current

    DESCRIPTION

        "Number of Label Range Components in the Initialization

        message.  This also represents the number of entries

        in the mplsLdpEntityAtmLRTable which correspond

        to this entry.

        This is the EXACT value for the ATM Session Parameter,

        field N (for Number of label range components).

        The ATM Session Parameter is an optional parameter

        in the Initialization Message.

        The description from rfc3036.txt is:

        'N, Number of label range components

           Specifies the number of ATM Label Range

           Components included in the TLV.'

         Please refer to the following reference for

         a complete description of this feature."

     REFERENCE

        "RFC3036, LDP Specification, Section 3.5.3

        Initialization Message."

    ::= { mplsLdpEntityAtmEntry 3 }

mplsLdpEntityAtmVcDirectionality OBJECT-TYPE

    SYNTAX      INTEGER {

                           bidirectional(0),

                           unidirectional(1)

                        }

    MAX-ACCESS  read-create

    STATUS      current

    DESCRIPTION

        "If the value of this object is 'bidirectional(0)',

        a given VCI, within a given VPI, is used as a

        label for both directions independently.

        If the value of this object is 'unidirectional(1)',

        a given VCI within a VPI designates one direction.

        This is the EXACT value for the ATM Session Parameter,

        field D (for VC Directionality).  The ATM Session

        Parameter is an optional parameter in the

        Initialization Message.

        The description from rfc3036.txt is:

        'D, VC Directionality

           A value of 0 specifies bidirectional VC capability,

           meaning the LSR can (within a given VPI) support

           the use of a given VCI as a label for both link

           directions independently.  A value of 1

           specifies unidirectional VC capability, meaning

           (within a given VPI) a given VCI may appear in

           a label mapping for one direction on the link

           only.  When either or both of the peers

           specifies unidirectional VC capability, both

           LSRs use unidirectional VC label assignment for

           the link as follows.  The LSRs compare their

           LDP Identifiers as unsigned integers.  The LSR

           with the larger LDP Identifier may assign

           only odd-numbered VCIs in the VPI/VCI

           range as labels.  The system with the smaller

           LDP Identifier may assign only even-numbered

           VCIs in the VPI/VCI range as labels.'

           Please refer to the following reference

           for a complete description of this feature."

     REFERENCE

        "RFC3036, LDP Specification, Section 3.5.3

        Initialization Message."

    ::= { mplsLdpEntityAtmEntry 4 }

mplsLdpEntityAtmLsrConnectivity OBJECT-TYPE

    SYNTAX      INTEGER {

                   direct(1),

                   indirect(2)

                }

    MAX-ACCESS  read-create

    STATUS      current

    DESCRIPTION

        "The peer LSR may be connected indirectly by means

        of an ATM VP so that the VPI values may be different

        on either endpoint so the label MUST be encoded

        entirely within the VCI field."

    DEFVAL { direct }

    ::= { mplsLdpEntityAtmEntry 5 }

mplsLdpEntityAtmDefaultControlVpi OBJECT-TYPE

    SYNTAX      AtmVpIdentifier

    MAX-ACCESS  read-create

    STATUS      current

    DESCRIPTION

        "The default VPI value for the non-MPLS connection.  The

        default value of this is 0 (zero) but other values may

        be configured.  This object allows a different value

        to be configured."

    DEFVAL { 0 }

    ::= { mplsLdpEntityAtmEntry 6 }

mplsLdpEntityAtmDefaultControlVci OBJECT-TYPE

    SYNTAX      MplsAtmVcIdentifier

    MAX-ACCESS  read-create

    STATUS      current

    DESCRIPTION

        "The Default VCI value for a non-MPLS connection.  The

        default value of this is 32 but other values may be

        configured.  This object allows a different value to

        be configured."

    DEFVAL { 32 }

    ::= { mplsLdpEntityAtmEntry 7 }

mplsLdpEntityAtmUnlabTrafVpi OBJECT-TYPE

    SYNTAX      AtmVpIdentifier

    MAX-ACCESS  read-create

    STATUS      current

    DESCRIPTION

        "VPI value of the VCC supporting unlabeled traffic.  This

        non-MPLS connection is used to carry unlabeled (IP)

        packets.  The default value is the same as the default

        value of the 'mplsLdpEntityAtmDefaultControlVpi', however

        another value may be configured."

    DEFVAL  { 0 }

    ::= { mplsLdpEntityAtmEntry 8 }

mplsLdpEntityAtmUnlabTrafVci OBJECT-TYPE

    SYNTAX      MplsAtmVcIdentifier

    MAX-ACCESS  read-create

    STATUS      current

    DESCRIPTION

        "VCI value of the VCC supporting unlabeled traffic.

        This non-MPLS connection is used to carry unlabeled (IP)

        packets. The default value is the same as the default

        value of the 'mplsLdpEntityAtmDefaultControlVci', however

        another value may be configured."

    DEFVAL  { 32 }

    ::= { mplsLdpEntityAtmEntry 9 }

mplsLdpEntityAtmStorageType  OBJECT-TYPE

    SYNTAX      StorageType

    MAX-ACCESS  read-create

    STATUS      current

    DESCRIPTION

        "The storage type for this conceptual row.

        Conceptual rows having the value 'permanent(4)'

        need not allow write-access to any columnar

        objects in the row."

    DEFVAL { nonVolatile }

    ::= { mplsLdpEntityAtmEntry 10 }

mplsLdpEntityAtmRowStatus OBJECT-TYPE

    SYNTAX      RowStatus

    MAX-ACCESS  read-create

    STATUS      current

    DESCRIPTION

        "The status of this conceptual row.  All writable

         objects in this row may be modified at any time,

         however, as described in detail in the section

         entitled, 'Changing Values After Session

         Establishment', and again described in the

         DESCRIPTION clause of the mplsLdpEntityAdminStatus

         object, if a session has been initiated with a Peer,

         changing objects in this table will wreak havoc

         with the session and interrupt traffic.  To repeat again:

         the recommended procedure is to set the

         mplsLdpEntityAdminStatus to down, thereby explicitly

         causing a session to be torn down. Then,

         change objects in this entry, then set the

         mplsLdpEntityAdminStatus to enable

         which enables a new session to be initiated."

    ::= { mplsLdpEntityAtmEntry 11 }

--

-- The MPLS LDP Entity ATM Label Range Table

--

mplsLdpEntityAtmLRTable OBJECT-TYPE

    SYNTAX SEQUENCE OF MplsLdpEntityAtmLREntry

    MAX-ACCESS not-accessible

    STATUS current

    DESCRIPTION

        "The MPLS LDP Entity ATM Label Range (LR) Table.

        The purpose of this table is to provide a mechanism

        for configuring a contiguous range of vpi's

        with a contiguous range of vci's, or a 'label range'

        for LDP Entities.

        LDP Entities which use ATM must have at least one

        entry in this table.

        There must exist at least one entry in this

        table for every LDP Entity that has

        'mplsLdpEntityOptionalParameters' object with

        a value of 'atmSessionParameters'."

    ::= { mplsLdpEntityAtmObjects 2 }

mplsLdpEntityAtmLREntry OBJECT-TYPE

    SYNTAX MplsLdpEntityAtmLREntry

    MAX-ACCESS not-accessible

    STATUS current

    DESCRIPTION

        "A row in the LDP Entity ATM Label

        Range Table.  One entry in this table contains

        information on a single range of labels

        represented by the configured Upper and Lower

        Bounds VPI/VCI pairs.  These are the same

        data used in the Initialization Message.

        NOTE:  The ranges for a specific LDP Entity

        are UNIQUE and non-overlapping.  For example,

        for a specific LDP Entity index, there could

        be one entry having LowerBound vpi/vci == 0/32, and

        UpperBound vpi/vci == 0/100, and a second entry

        for this same interface with LowerBound

        vpi/vci == 0/101 and UpperBound vpi/vci == 0/200.

        However, there could not be a third entry with

        LowerBound vpi/vci == 0/200 and

        UpperBound vpi/vci == 0/300 because this label

        range overlaps with the second entry (i.e., both

        entries now have 0/200).

        A row will not become active unless a unique and

        non-overlapping range is specified.

        At least one label range entry for a

        specific LDP Entity MUST

        include the default VPI/VCI  values denoted

        in the LDP Entity Table.

        A request to create a row with an overlapping

        range should result in an inconsistentValue

        error."

    INDEX       {  mplsLdpEntityLdpId,

                   mplsLdpEntityIndex,

                   mplsLdpEntityAtmLRMinVpi,

                   mplsLdpEntityAtmLRMinVci

                }

    ::= { mplsLdpEntityAtmLRTable 1 }

MplsLdpEntityAtmLREntry ::= SEQUENCE {

    mplsLdpEntityAtmLRMinVpi       AtmVpIdentifier,

    mplsLdpEntityAtmLRMinVci       MplsAtmVcIdentifier,

    mplsLdpEntityAtmLRMaxVpi       AtmVpIdentifier,

    mplsLdpEntityAtmLRMaxVci       MplsAtmVcIdentifier,

    mplsLdpEntityAtmLRStorageType  StorageType,

    mplsLdpEntityAtmLRRowStatus    RowStatus

}

mplsLdpEntityAtmLRMinVpi OBJECT-TYPE

    SYNTAX AtmVpIdentifier

    MAX-ACCESS not-accessible

    STATUS current

    DESCRIPTION

        "The minimum VPI number configured for this range.

        The value of zero is a valid value for the VPI portion

        of the label."

    ::= { mplsLdpEntityAtmLREntry 1 }

mplsLdpEntityAtmLRMinVci OBJECT-TYPE

    SYNTAX MplsAtmVcIdentifier

    MAX-ACCESS not-accessible

    STATUS current

    DESCRIPTION

        "The minimum VCI number configured for this range."

    ::= { mplsLdpEntityAtmLREntry 2 }

mplsLdpEntityAtmLRMaxVpi OBJECT-TYPE

    SYNTAX AtmVpIdentifier

    MAX-ACCESS read-create

    STATUS current

    DESCRIPTION

        "The maximum VPI number configured for this range."

    ::= { mplsLdpEntityAtmLREntry 3 }

mplsLdpEntityAtmLRMaxVci OBJECT-TYPE

    SYNTAX MplsAtmVcIdentifier

    MAX-ACCESS read-create

    STATUS current

    DESCRIPTION

        "The maximum VCI number configured for this range."

   ::= { mplsLdpEntityAtmLREntry 4 }

mplsLdpEntityAtmLRStorageType  OBJECT-TYPE

    SYNTAX      StorageType

    MAX-ACCESS  read-create

    STATUS      current

    DESCRIPTION

        "The storage type for this conceptual row.

        Conceptual rows having the value 'permanent(4)'

        need not allow write-access to any columnar

        objects in the row."

    DEFVAL { nonVolatile }

    ::= { mplsLdpEntityAtmLREntry 5 }

mplsLdpEntityAtmLRRowStatus OBJECT-TYPE

    SYNTAX RowStatus

    MAX-ACCESS read-create

    STATUS current

    DESCRIPTION

        "The status of this conceptual row.  All writable

         objects in this row may be modified at any time,

         however, as described in detail in the section

         entitled, 'Changing Values After Session

         Establishment', and again described in the

         DESCRIPTION clause of the

         mplsLdpEntityAdminStatus object,

         if a session has been initiated with a Peer,

         changing objects in this table will

         wreak havoc with the session and interrupt traffic.

         To repeat again:  the recommended procedure

         is to set the mplsLdpEntityAdminStatus to

         down, thereby explicitly causing a session

         to be torn down. Then, change objects in this

         entry, then set the mplsLdpEntityAdminStatus

         to enable which enables a new session

         to be initiated."

    ::= { mplsLdpEntityAtmLREntry 6 }

--

-- MPLS LDP ATM Session Information

--

mplsLdpAtmSessionObjects OBJECT IDENTIFIER ::=

                               { mplsLdpAtmObjects 2 }

mplsLdpAtmSessionTable OBJECT-TYPE

    SYNTAX      SEQUENCE OF MplsLdpAtmSessionEntry

    MAX-ACCESS  not-accessible

    STATUS      current

    DESCRIPTION

        "A table which relates sessions in the

        'mplsLdpSessionTable' and their label

        range intersections.  There could be one

        or more label range intersections between an

        LDP Entity and LDP Peer using ATM as the

        underlying  media.  Each row represents

        a single label range intersection.

        This table cannot use the 'AUGMENTS'

        clause because there is not necessarily

        a one-to-one mapping between this table

        and the mplsLdpSessionTable."

    ::= { mplsLdpAtmSessionObjects 1 }

mplsLdpAtmSessionEntry OBJECT-TYPE

    SYNTAX      MplsLdpAtmSessionEntry

    MAX-ACCESS  not-accessible

    STATUS      current

    DESCRIPTION

        "An entry in this table represents information on a

        single label range intersection between an LDP Entity

        and LDP Peer.

        The information contained in a row is read-only."

    INDEX       { mplsLdpEntityLdpId,

                  mplsLdpEntityIndex,

                  mplsLdpPeerLdpId,

                  mplsLdpSessionAtmLRLowerBoundVpi,

                  mplsLdpSessionAtmLRLowerBoundVci

                }

    ::= { mplsLdpAtmSessionTable 1 }

MplsLdpAtmSessionEntry ::= SEQUENCE {

    mplsLdpSessionAtmLRLowerBoundVpi     AtmVpIdentifier,

    mplsLdpSessionAtmLRLowerBoundVci     MplsAtmVcIdentifier,

    mplsLdpSessionAtmLRUpperBoundVpi     AtmVpIdentifier,

    mplsLdpSessionAtmLRUpperBoundVci     MplsAtmVcIdentifier

}

mplsLdpSessionAtmLRLowerBoundVpi OBJECT-TYPE

    SYNTAX AtmVpIdentifier

    MAX-ACCESS not-accessible

    STATUS current

    DESCRIPTION

        "The minimum VPI number for this range."

    ::= { mplsLdpAtmSessionEntry 1 }

mplsLdpSessionAtmLRLowerBoundVci OBJECT-TYPE

    SYNTAX MplsAtmVcIdentifier

    MAX-ACCESS not-accessible

    STATUS current

    DESCRIPTION

        "The minimum VCI number for this range."

    ::= { mplsLdpAtmSessionEntry 2 }

mplsLdpSessionAtmLRUpperBoundVpi OBJECT-TYPE

    SYNTAX AtmVpIdentifier

    MAX-ACCESS read-only

    STATUS current

    DESCRIPTION

        "The maximum VPI number for this range."

    ::= { mplsLdpAtmSessionEntry 3 }

mplsLdpSessionAtmLRUpperBoundVci OBJECT-TYPE

    SYNTAX MplsAtmVcIdentifier

    MAX-ACCESS read-only

    STATUS current

    DESCRIPTION

        "The maximum VCI number for this range."

    ::= { mplsLdpAtmSessionEntry 4 }

--**************************************************************

-- Module Conformance Statement

--**************************************************************

mplsLdpAtmGroups

    OBJECT IDENTIFIER ::= { mplsLdpAtmConformance 1 }

mplsLdpAtmCompliances

    OBJECT IDENTIFIER ::= { mplsLdpAtmConformance 2 }

--

-- Full Compliance

--

mplsLdpAtmModuleFullCompliance MODULE-COMPLIANCE

    STATUS current

    DESCRIPTION

        "The Module is implemented with support for

        read-create and read-write.  In other words,

        both monitoring and configuration

        are available when using this MODULE-COMPLIANCE."

    MODULE -- this module

    MANDATORY-GROUPS    {

                           mplsLdpAtmGroup

                        }

    OBJECT       mplsLdpEntityAtmRowStatus

    SYNTAX       RowStatus { active(1) }

    WRITE-SYNTAX RowStatus { createAndGo(4), destroy(6) }

    DESCRIPTION

       "Support for createAndWait and notInService is not required."

    OBJECT       mplsLdpEntityAtmLRRowStatus

    SYNTAX       RowStatus { active(1) }

    WRITE-SYNTAX RowStatus { createAndGo(4), destroy(6) }

    DESCRIPTION

       "Support for createAndWait and notInService is not required."

    ::= { mplsLdpAtmCompliances 1 }

--

-- Read-Only Compliance

--

mplsLdpAtmModuleReadOnlyCompliance MODULE-COMPLIANCE

    STATUS current

    DESCRIPTION

        "The Module is implemented with support for

        read-only.  In other words, only monitoring

        is available by implementing this MODULE-COMPLIANCE."

    MODULE -- this module

    MANDATORY-GROUPS    {

                           mplsLdpAtmGroup

                        }

    OBJECT       mplsLdpEntityAtmIfIndexOrZero

    MIN-ACCESS   read-only

    DESCRIPTION

       "Write access is not required."

    OBJECT       mplsLdpEntityAtmMergeCap

    MIN-ACCESS   read-only

    DESCRIPTION

       "Write access is not required."

    OBJECT       mplsLdpEntityAtmVcDirectionality

    MIN-ACCESS   read-only

    DESCRIPTION

       "Write access is not required."

    OBJECT       mplsLdpEntityAtmLsrConnectivity

    MIN-ACCESS   read-only

    DESCRIPTION

       "Write access is not required."

    OBJECT       mplsLdpEntityAtmDefaultControlVpi

    MIN-ACCESS   read-only

    DESCRIPTION

       "Write access is not required."

    OBJECT       mplsLdpEntityAtmDefaultControlVci

    MIN-ACCESS   read-only

    DESCRIPTION

       "Write access is not required."

    OBJECT       mplsLdpEntityAtmUnlabTrafVpi

    MIN-ACCESS   read-only

    DESCRIPTION

       "Write access is not required."

    OBJECT       mplsLdpEntityAtmUnlabTrafVci

    MIN-ACCESS   read-only

    DESCRIPTION

       "Write access is not required."

    OBJECT       mplsLdpEntityAtmStorageType

    MIN-ACCESS   read-only

    DESCRIPTION

       "Write access is not required."

    OBJECT       mplsLdpEntityAtmRowStatus

    SYNTAX       RowStatus { active(1) }

    MIN-ACCESS   read-only

    DESCRIPTION

       "Write access is not required, and active is the

       only status that needs to be supported."

    OBJECT       mplsLdpEntityAtmLRMaxVpi

    MIN-ACCESS   read-only

    DESCRIPTION

       "Write access is not required."

    OBJECT       mplsLdpEntityAtmLRMaxVci

    MIN-ACCESS   read-only

    DESCRIPTION

       "Write access is not required."

    OBJECT       mplsLdpEntityAtmLRStorageType

    MIN-ACCESS   read-only

    DESCRIPTION

       "Write access is not required."

    OBJECT       mplsLdpEntityAtmLRRowStatus

    SYNTAX       RowStatus { active(1) }

    MIN-ACCESS   read-only

    DESCRIPTION

       "Write access is not required, and active is the

       only status that needs to be supported."

    ::= { mplsLdpAtmCompliances 2 }

--

-- units of conformance

--

mplsLdpAtmGroup OBJECT-GROUP

    OBJECTS {

    mplsLdpEntityAtmIfIndexOrZero,

    mplsLdpEntityAtmMergeCap,

    mplsLdpEntityAtmLRComponents,

    mplsLdpEntityAtmVcDirectionality,

    mplsLdpEntityAtmLsrConnectivity,

    mplsLdpEntityAtmDefaultControlVpi,

    mplsLdpEntityAtmDefaultControlVci,

    mplsLdpEntityAtmUnlabTrafVpi,

    mplsLdpEntityAtmUnlabTrafVci,

    mplsLdpEntityAtmStorageType,

    mplsLdpEntityAtmRowStatus,

    mplsLdpEntityAtmLRMaxVpi,

    mplsLdpEntityAtmLRMaxVci,

    mplsLdpEntityAtmLRStorageType,

    mplsLdpEntityAtmLRRowStatus,

    mplsLdpSessionAtmLRUpperBoundVpi,

    mplsLdpSessionAtmLRUpperBoundVci

    }

    STATUS    current

    DESCRIPTION

        "Objects that apply to all MPLS LDP implementations

        using ATM as the Layer 2."

    ::= { mplsLdpAtmGroups 1 }

END