.\" Man page generated from reStructuredText.

.

.TH IBPORTSTATE 8 "" "" "Open IB Diagnostics"

.SH NAME

IBPORTSTATE \- handle port (physical) state and link speed of an InfiniBand port

.

.nr rst2man-indent-level 0

.

.de1 rstReportMargin

\\$1 \\n[an-margin]

level \\n[rst2man-indent-level]

level margin: \\n[rst2man-indent\\n[rst2man-indent-level]]

-

\\n[rst2man-indent0]

\\n[rst2man-indent1]

\\n[rst2man-indent2]

..

.de1 INDENT

.\" .rstReportMargin pre:

. RS \\$1

. nr rst2man-indent\\n[rst2man-indent-level] \\n[an-margin]

. nr rst2man-indent-level +1

.\" .rstReportMargin post:

..

.de UNINDENT

. RE

.\" indent \\n[an-margin]

.\" old: \\n[rst2man-indent\\n[rst2man-indent-level]]

.nr rst2man-indent-level -1

.\" new: \\n[rst2man-indent\\n[rst2man-indent-level]]

.in \\n[rst2man-indent\\n[rst2man-indent-level]]u

..

.SH SYNOPSIS

.sp

ibportstate [options] <dest dr_path|lid|guid> <portnum> [<op>]

.SH DESCRIPTION

.sp

ibportstate allows the port state and port physical state of an IB port

to be queried (in addition to link width and speed being validated

relative to the peer port when the port queried is a switch port),

or a switch port to be disabled, enabled, or reset. It

also allows the link speed/width enabled on any IB port to be adjusted.

.SH OPTIONS

.INDENT 0.0

.TP

.B \fB<op>\fP

.INDENT 7.0

.TP

.B Supported ops: enable, disable, reset, speed, espeed, fdr10, width, query,

on, off, down, arm, active, vls, mtu, lid, smlid, lmc,

mkey, mkeylease, mkeyprot

(Default is query)

.UNINDENT

.sp

\fBenable, disable, and reset\fP are only allowed on switch ports (An

error is indicated if attempted on CA or router ports)

.sp

\fBoff\fP change the port state to disable.

.sp

\fBon\fP change the port state to enable(only when the current state is disable).

.sp

\fBspeed and width\fP are allowed on any port

.sp

\fBspeed\fP values are the legal values for PortInfo:LinkSpeedEnabled (An

error is indicated if PortInfo:LinkSpeedSupported does not support this

setting)

.sp

\fBespeed\fP is allowed on any port supporting extended link speeds

.sp

\fBfdr10\fP is allowed on any port supporting fdr10 (An error is

indicated if port\(aqs capability mask indicates extended link speeds are

not supported or if PortInfo:LinkSpeedExtSupported does not support

this setting)

.sp

\fBwidth\fP values are legal values for PortInfo:LinkWidthEnabled (An

error is indicated if PortInfo:LinkWidthSupported does not support this

setting) (NOTE: Speed and width changes are not effected until the port

goes through link renegotiation)

.sp

\fBquery\fP also validates port characteristics (link width, speed,

espeed, and fdr10) based on the peer port. This checking is done when

the port queried is a switch port as it relies on combined routing (an

initial LID route with directed routing to the peer) which can only be

done on a switch. This peer port validation feature of query op

requires LID routing to be functioning in the subnet.

.sp

\fBmkey, mkeylease, and mkeyprot\fP are only allowed on CAs, routers, or

switch port 0 (An error is generated if attempted on external switch

ports).  Hexadecimal and octal mkeys may be specified by prepending the

key with \(aq0x\(aq or \(aq0\(aq, respectively.  If a non\-numeric value (like \(aqx\(aq)

is specified for the mkey, then ibportstate will prompt for a value.

.UNINDENT

.SS Addressing Flags

.\" Define the common option -L

.

.sp

\fB\-L, \-\-Lid\fP   The address specified is a LID

.\" Define the common option -G

.

.sp

\fB\-G, \-\-Guid\fP     The address specified is a Port GUID

.\" Define the common option -D for Directed routes

.

.sp

\fB\-D, \-\-Direct\fP     The address specified is a directed route

.INDENT 0.0

.INDENT 3.5

.sp

.nf

.ft C

Examples:

   [options] \-D [options] "0"          # self port

   [options] \-D [options] "0,1,2,1,4"  # out via port 1, then 2, ...

   (Note the second number in the path specified must match the port being

   used.  This can be specified using the port selection flag \(aq\-P\(aq or the

   port found through the automatic selection process.)

.ft P

.fi

.UNINDENT

.UNINDENT

.\" Define the common option -s

.

.sp

\fB\-s, \-\-sm_port <smlid>\fP     use \(aqsmlid\(aq as the target lid for SA queries.

.SS Port Selection flags

.\" Define the common option -C

.

.sp

\fB\-C, \-\-Ca <ca_name>\fP    use the specified ca_name.

.\" Define the common option -P

.

.sp

\fB\-P, \-\-Port <ca_port>\fP    use the specified ca_port.

.\" Explanation of local port selection

.

.SS Local port Selection

.sp

Multiple port/Multiple CA support: when no IB device or port is specified

(see the "local umad parameters" below), the libibumad library

selects the port to use by the following criteria:

.INDENT 0.0

.INDENT 3.5

.INDENT 0.0

.IP 1. 3

the first port that is ACTIVE.

.IP 2. 3

if not found, the first port that is UP (physical link up).

.UNINDENT

.sp

If a port and/or CA name is specified, the libibumad library attempts

to fulfill the user request, and will fail if it is not possible.

.sp

For example:

.INDENT 0.0

.INDENT 3.5

.sp

.nf

.ft C

ibaddr                 # use the first port (criteria #1 above)

ibaddr \-C mthca1       # pick the best port from "mthca1" only.

ibaddr \-P 2            # use the second (active/up) port from the first available IB device.

ibaddr \-C mthca0 \-P 2  # use the specified port only.

.ft P

.fi

.UNINDENT

.UNINDENT

.UNINDENT

.UNINDENT

.SS Configuration flags

.\" Define the common option -z

.

.sp

\fB\-\-config, \-z  <config_file>\fP Specify alternate config file.

.INDENT 0.0

.INDENT 3.5

Default: /usr/local/etc/infiniband-diags/ibdiag.conf

.UNINDENT

.UNINDENT

.\" Define the common option -t

.

.sp

\fB\-t, \-\-timeout <timeout_ms>\fP override the default timeout for the solicited mads.

.\" Define the common option -y

.

.INDENT 0.0

.TP

.B \fB\-y, \-\-m_key <key>\fP

use the specified M_key for requests. If non\-numeric value (like \(aqx\(aq)

is specified then a value will be prompted for.

.UNINDENT

.SS Debugging flags

.\" Define the common option -h

.

.sp

\fB\-h, \-\-help\fP      show the usage message

.\" Define the common option -d

.

.INDENT 0.0

.TP

.B \-d

raise the IB debugging level.

May be used several times (\-ddd or \-d \-d \-d).

.UNINDENT

.\" Define the common option -e

.

.INDENT 0.0

.TP

.B \-e

show send and receive errors (timeouts and others)

.UNINDENT

.\" Define the common option -K

.

.INDENT 0.0

.TP

.B \fB\-K, \-\-show_keys\fP

show security keys (mkey, smkey, etc.) associated with the request.

.UNINDENT

.\" Define the common option -v

.

.INDENT 0.0

.TP

.B \fB\-v, \-\-verbose\fP

increase the application verbosity level.

May be used several times (\-vv or \-v \-v \-v)

.UNINDENT

.\" Define the common option -V

.

.sp

\fB\-V, \-\-version\fP     show the version info.

.SH FILES

.\" Common text for the config file

.

.SS CONFIG FILE

.sp

/usr/local/etc/infiniband-diags/ibdiag.conf

.sp

A global config file is provided to set some of the common options for all

tools.  See supplied config file for details.

.SH EXAMPLES

.INDENT 0.0

.TP

.B ::

ibportstate 3 1 disable                  # by lid

ibportstate \-G 0x2C9000100D051 1 enable  # by guid

ibportstate \-D 0 1                       # (query) by direct route

ibportstate 3 1 reset                    # by lid

ibportstate 3 1 speed 1                  # by lid

ibportstate 3 1 width 1                  # by lid

ibportstate \-D 0 1 lid 0x1234 arm        # by direct route

.UNINDENT

.SH AUTHOR

.INDENT 0.0

.TP

.B Hal Rosenstock

< \fI\%hal.rosenstock@gmail.com\fP >

.UNINDENT

.\" Generated by docutils manpage writer.

.